https://forge.codesys.com/forge/talk/CODESYS-V2/thread/ec14f31f2d/2020-02-27T22:10:41.116000ZRecent posts to Connecting to Rexroth RC6_9_202020-02-27T22:10:41.116000Z2020-02-27T22:10:41.116000Zbjornashttps://forge.codesys.com/u/bjornas/https://forge.codesys.comc62a32a28e95096d47b4d35034d598903bf0b32c

<div class="markdown_content"><p>Thanks, I will try!</p></div>

2020-02-27T22:10:39.591000Z2020-02-27T22:10:39.591000Zshooterhttps://forge.codesys.com/u/shooter/https://forge.codesys.com685d43f364f8408ea931d24e559dba3640ba9a1d

<div class="markdown_content"><p>this is outside the scope of codesys, <br/> however have a look at settings if the compiler makes a correct hex file and obvious where it is stored.<br/> check the project directory.</p></div>

2020-02-27T22:10:35.328000Z2020-02-27T22:10:35.328000Zbjornashttps://forge.codesys.com/u/bjornas/https://forge.codesys.com808c630e5857b8caba1643671b83d266f6208e09

<div class="markdown_content"><p>Ok, so I`ve been able to connect to the RC.<br/> Used Bodas Service 3.5 to flash an existing HEX. file into the RC, and then downloaded a test program.<br/> When opening Bodas design after doing a "rebuild all" I got a message "Not found HEX-File:C:\ xxx\xxxx"<br/> Have I done something wrong here?<br/> I could go online without problems.....</p></div>

2020-02-27T22:10:33.802000Z2020-02-27T22:10:33.802000Zbjornashttps://forge.codesys.com/u/bjornas/https://forge.codesys.com1f8fd85c845e324f45b678c3a22da45c2e71a13f

<div class="markdown_content"><p>Thanks for information!</p></div>

2020-02-27T22:10:29.573000Z2020-02-27T22:10:29.573000Zshooterhttps://forge.codesys.com/u/shooter/https://forge.codesys.com3a2a96d3a9ea4904b0857eb6054fcde23a1f4c0f

<div class="markdown_content"><p>The project must be saved on the device, otherwise it is impossible to open it.<br/> a program is compiled in the PC and send to the PLC as a machinelanguage, so you can not download from the device as a compiled file is unreadable (for the most people)</p></div>

2020-02-27T22:10:28.041000Z2020-02-27T22:10:28.041000Zbjornashttps://forge.codesys.com/u/bjornas/https://forge.codesys.coma09afb300ca398dd819572c37fd702fc32599b91

<div class="markdown_content"><p>Hello!<br/> I am trying to etablish a connection to a Rexroth RC6_9_20 with Bodas Design 3.0.17.<br/> I want to read out the program from the RC, and save it on my Computer<br/> Could someone please tell me if there is a kind of tutorial here at this forum how to set this up?<br/> Here is what I do:<br/> File - Open - Open project from PLC - PLC - Target Setting _ RC6-9 20 Standard V1.9 - Interface - Peak PCAN-USB - Devicetype RC4-6/22 - Scan</p> <p>I cannot connect, any ideas what`s wrong?</p> <p>Thanks in advance !<br/> Newbe</p></div>