File reading or writing error

2020-10-10T13:53:17.340000Z

Found the problem.

Had to add

 fileopen(xExecute:=FALSE);
 fileread(xExecute:=FALSE);

in state 2 when file read is complete.

Thanks

File reading or writing error

2020-10-09T20:06:51.137000Z

Hi Thomas
I rewrote the sequential reading and writing code of the 3 files, implementing a simple CASE state machine and it seems that the problem is in the write and read file function block.
It seems that the error always appear during state 3 when file that was read must be closed as it is shown in the attached picture.
Below is the code of read file function block.

IF xReadStart THEN
    CASE uiReadStatus OF

    0:  (* Start *)
        fileopen(xExecute:=FALSE);
        fileread(xExecute:=FALSE);
        fileclose(xExecute:=FALSE);
        uiReadStatus:=uiReadStatus+1;

    1: (* open a test.txt file *)
        fileopen.sFileName:=sFileName;                               
        fileopen.eFileMode:=1;                 
        fileopen.xExclusive:=TRUE;
        fileopen(xExecute:=TRUE);
        IF fileopen.xDone THEN
            hFile:=fileopen.hFile;
            uiReadStatus:=uiReadStatus+1;
        END_IF
        IF fileopen.xError THEN
            (* error handling*)
            eError := fileopen.eError;
        END_IF     

    2:  (* read file*)
        fileread.hFile:=hFile;
        fileread.udiTimeOut:=1000000;                      (* 100ms Timeout *)
        fileread.pBuffer:=ADR(sFileString);
        sFileString := sFileString;
        fileread.szBuffer:=SIZEOF(sFileString);
        fileread(xExecute:=TRUE);
        IF fileread.xDone THEN
            uiReadStatus:=uiReadStatus+1;
        END_IF
        IF fileread.xError THEN
           (* error handling*)
           eError := fileread.eError;
        END_IF

    3:  (* close file*)
        fileclose.hFile:=hFile;
        fileclose(xExecute:=TRUE);
        IF fileclose.xDone THEN
            uiReadStatus:=uiReadStatus+1;
            xExtractParams:=TRUE;
        END_IF
        IF fileclose.xError THEN
            (* error handling*)
            eError := fileclose.eError;
        END_IF

    4:  //Loop through string until there is no string left or array has hit its limits
            WHILE StrLenA(pstData:= ADR(sFileString)) > 0 DO
                //Find location of first break point
                iSplitLocation := StrFindA(pst1:= ADR(sFileString), pst2:= ADR(sSplitChars), uiSearchStart:= 1) - 1;

                //If there is no break point found then set location to size of string
                IF iSplitLocation = -1 THEN
                    iSplitLocation := DINT_TO_INT(StrLenA(pstData:= ADR(sFileString)));
                END_IF

                //Copy the part of the string that is needed for the parameter.
                StrMidA(
                        pst:= ADR(sFileString), 
                        uiInputBufferSize:= SIZEOF(sFileString), 
                        iLength:= iSplitLocation, 
                        iPosition:= 1, 
                        pstResult:= ADR(sShortString), 
                        uiResultBufferSize:= SIZEOF(sShortString));

                //Make sure string is not empty before using up an array spot.
                IF StrLenA(pstData:= ADR(sShortString)) > 0 THEN
                    arParameters[iCount] := STRING_TO_INT(sShortString);
                    iCount := iCount + 1;
                END_IF

                //Remove copied components from long string
                StrDeleteA(pby:= ADR(sFileString), iLength:= (iSplitLocation + 2), iPosition:= 1);

                //Check to see if more parameters can fit in array. If not exit loop
                IF iCount > MAX_PARAMETERS THEN
                    iCount := 0;
                    EXIT;
                END_IF 
            END_WHILE
            //xExtractParams := FALSE;
            uiReadStatus := uiReadStatus+1;

    5: (* end of procedure *)
        xExtractionComplete := TRUE;    

    END_CASE
ELSE
    eError := FILE.ERROR.NO_ERROR;
    xExtractionComplete := FALSE;
    uiReadStatus:=0;    
END_IF

File reading or writing error

2020-10-09T12:44:07.946000Z

Sorry, I haven't read that you start a new job after finished the old one. Are other libraries in your project, which use the AsyncManger. F. e. CAA NetBaseSrv

File reading or writing error

2020-10-09T12:40:09.116000Z

Dear Kallileo,
The number of jobs is limited in the Runtime. This limit applies to all libraries together!!!!

Do you have several jobs (reading/writting) at the same time?
== >> Make sure that a new job is not started until the other one is finished.

Regards Thomas

File reading or writing error

2020-10-09T12:16:54.541000Z

I'm using Codesys 3.5.12 and File Access library 3.5.7 to read and write 3 user configuration files and 3 to read default configuration files. The files are not big with around 100 parameters each.

Usually it works but many times it's randomly throwing the following error:
ASM_CREATEJOB_FAILED
5113 Job creation of AsyncManager failed

I read and write the files sequentially. As soon reading/writing of the first files is complete it goes to the next one. I have also tried to put time delay in between but the error is still there and it's driving me crazy.

Recent posts to File reading or writing error

File reading or writing error

File reading or writing error

File reading or writing error

File reading or writing error

File reading or writing error