CODESYS Forge - CODESYS Forge / Talk / Engineering 🇬🇧: Codesys EoE help.

Welcome to our new forum
All users of the legacy CODESYS Forums, please create a new account at account.codesys.com. But make sure to use the same E-Mail address as in the old Forum. Then your posts will be matched. Close

Codesys EoE help.

Forum: Engineering 🇬🇧

Creator: chiali

Created: 2022-04-15

Updated: 2022-06-23

chiali - 2022-04-15

Hi,
I would like to connect to a servo-drive through EoE protocol using it Software tool
and Codesys; but I don't see how to do it and I didn't find it in the Codesys help.

NB:The drive is Digitax_HD and the software is CONNECT.

Regards.
Chiali

If you would like to refer to this comment somewhere else in this project, copy and paste the following link:

wollvieh - 2022-04-15

https://store.codesys.com/en/ethercat-example.html

If you would like to refer to this comment somewhere else in this project, copy and paste the following link:

chiali - 2022-04-15

Thanks for the reply. But I'm using the CONNECT software to parametrize the M753 servo-drive using the Ethernet over Ethercat EoE tab of Codesys (without any code).

Screenshot (2).png

If you would like to refer to this comment somewhere else in this project, copy and paste the following link:

eschwellinger - 2022-04-16

which version of CODESYS and which versions of the EtherCAT libraries?

If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
- chiali - 2022-04-16
  
  Versions of CODESYS and Ethercat Lib: V3.5.17.0.
  
  If you would like to refer to this comment somewhere else in this project, copy and paste the following link:

eschwellinger - 2022-04-17

should work, depending on your plc (Control Win or Linux based device)
you need to setup tap device (for Linux) for Windows Loopback adapter need to be installed

If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
- chiali - 2022-04-17
  
  I'm using Control win.
  How to use Loopback adapter: I tried to use it but in vain I mean no connection with The CONNECT software.
  
  If you would like to refer to this comment somewhere else in this project, copy and paste the following link:

eschwellinger - 2022-04-17

I think you should update all to SP18, there was a bugfix for Windows 10 and Control Win on EOE as I remember.

If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
- chiali - 2022-04-17
  
  Ok I will try it and hope this will work.
  
  Is there a way to update from SP17 to SP18 not to have two installed versions ?
  Thanks.
  
  If you would like to refer to this comment somewhere else in this project, copy and paste the following link:

eschwellinger - 2022-04-18

I would use the CODESYS installer if you need to remove it.

Last edit: eschwellinger 2022-04-18

If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
- chiali - 2022-04-18
  
  Great it works perfectly.
  Thannnnnnks.
  
  If you would like to refer to this comment somewhere else in this project, copy and paste the following link:

spiritcore - 2022-06-23

Hi,
I have the same servo drive but can't find the EoE tab.
Using Codesys V3.5 SP18 Patch 2.
What have I missed?

AnyDesk_50e9i2lEKJ.png

If you would like to refer to this comment somewhere else in this project, copy and paste the following link:

chiali - 2022-06-23

Hi,
In the General Tab "Check in" the Expert settings.

Screenshot (6)_LI.jpg

If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
- spiritcore - 2022-06-23
  
  Found, Thank you!
  
  If you would like to refer to this comment somewhere else in this project, copy and paste the following link:

Log in to post a comment.