Welcome to our new forum
All users of the legacy CODESYS Forums, please create a new account at account.codesys.com. But make sure to use the same E-Mail address as in the old Forum. Then your posts will be matched.
Close
Hi,
I had installed the new version of RTE 3.5.16 x64 and try to run the project attached. I had compiled the code without error but once login. The error happen.
I will attach the project later.
Hi,
please check the plclogger for more information,
guess you need to add the CODESYS network driver on Windows and add the component in the RTE configuration if you want to use Ethercat in your project.
BR
Edwin
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Hi Edwin,
Thanks for the fast response. I am able to compile and login now. The control RTE can only access 'CmpEt1000Drv' right?
After download and run, the Ethercat master is not able to communicate with my robot through the EL6695.
I had tested with control win 3.5.16 x64 with Intel Ethercat driver (SysEthernet) and it is working.
How should I proceed from here?
you need to remove SysEthernet this is not needed on Control RTE,
only the CmpEt1000Drv ... and a reset cold of the pc is needed after changing the driver under windows ( means switch off an on again - after reboot windows)
Then it will work.
BR
Edwin
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Hi Edwin,
I believe it got to do with the driver for the ethernet port. i had shutdown and power back and it is not able to install the driver anymore.
I successfully update the driver, but it has '!' on the Codesys driver after cycle power.
I will put this aside first as i had test with another PC and it all works fine.
I may revert back my window OS to default and test again.
Thank you for your support.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Hi,
I had installed the new version of RTE 3.5.16 x64 and try to run the project attached. I had compiled the code without error but once login. The error happen.
I will attach the project later.
more posts ...
Hi,
This is the attached project.
Hi,
please check the plclogger for more information,
guess you need to add the CODESYS network driver on Windows and add the component in the RTE configuration if you want to use Ethercat in your project.
BR
Edwin
Hi Edwin,
Thanks for the fast response. I am able to compile and login now. The control RTE can only access 'CmpEt1000Drv' right?
After download and run, the Ethercat master is not able to communicate with my robot through the EL6695.
I had tested with control win 3.5.16 x64 with Intel Ethercat driver (SysEthernet) and it is working.
How should I proceed from here?
Hi,
after I run, there is an error on the Ethercat Master stated in the picture attached.
Hi Edwin,
On top of that, I cannot browse the ethernet card once i had connected to the soft PLC.
Please refer to the picture attached.
Hi Edwin,
After a long wait, I got the following as shown in the picture attached
you need to remove SysEthernet this is not needed on Control RTE,
only the CmpEt1000Drv ... and a reset cold of the pc is needed after changing the driver under windows ( means switch off an on again - after reboot windows)
Then it will work.
BR
Edwin
Hi Edwin,
May I request a Teamviewer support? I had done all the trials and everything seems fine but i cannot browse and select the ethernet port.
Only possible If you write to 'my question' in the CODEDSYS Store..
Hi Edwin,
I had raised a ticket in 'My Question'. Hope to hear from you soon.
ThanksHi Edwin,
You may log in to the teamviewer anytime from now.
ThanksHi Edwin,
I believe it got to do with the driver for the ethernet port. i had shutdown and power back and it is not able to install the driver anymore.
I successfully update the driver, but it has '!' on the Codesys driver after cycle power.
I will put this aside first as i had test with another PC and it all works fine.
I may revert back my window OS to default and test again.
Thank you for your support.