https://forge.codesys.com/forge/talk/Engineering/thread/a1e9339a2a/2020-02-27T14:07:14.335000ZRecent posts to Not displaying the full names2020-02-27T14:07:14.335000Z2020-02-27T14:07:14.335000ZJeffreyThijssenhttps://forge.codesys.com/u/jeffreythijssen/https://forge.codesys.com3f245c34638f48b8f33dee0eb01d7880d43d12f7

<div class="markdown_content"><p>Hello,</p> <p>When I put a function into a ladder element. Some of the inputs are shortened.<br/> For example I_Reco...</p> <div class="codehilite"><pre><span></span><span class="nv">VAR_INPUT</span> <span class="nv">i_CommonSetting</span> : <span class="nv">UDT_SettCommon</span><span class="c1">; //Default settings</span> <span class="nv">i_Setting</span> : <span class="nv">UDT_SettTrs01</span><span class="c1">; //Settings of the transport section</span> <span class="nv">i_CFG</span> : <span class="nv">UDT_CfgTrs01</span><span class="c1">; //Configuration parameters</span> <span class="nv">i_General</span> : <span class="nv">UDT_General</span><span class="c1">; //Previous cycle time [us]</span> <span class="nv">i_Record</span> : <span class="nv">DINT</span><span class="c1">; //Record within Position DataBlock Downstream section</span> <span class="nv">i_RecordDownstream</span>: <span class="nv">DINT</span> <span class="c1">; //Record of the downstream section</span> <span class="nv">i_CmdEnable</span> : <span class="nv">BOOL</span><span class="c1">; //CMD: Enable command</span> <span class="nv">i_CmdStart</span> : <span class="nv">BOOL</span><span class="c1">; //CMD: Start command</span> <span class="nv">i_CmdReset</span> : <span class="nv">BOOL</span><span class="c1">; //CMD: Reset command</span> <span class="nv">i_CmdStop</span> : <span class="nv">BOOL</span><span class="c1">; //CMD: Controlled stop</span> <span class="nv">i_CmdIoAvailable</span> : <span class="nv">BOOL</span><span class="c1">; //CMD: Signal for indication IO is OK (no Fieldbus or IO error)</span> <span class="nv">i_CmdSafetyOk</span> : <span class="nv">BOOL</span><span class="c1">; //CMD: Safety is OK signal</span> <span class="nv">i_CmdReverse</span> : <span class="nv">BOOL</span><span class="c1">; //CMD: Running reverse</span> <span class="nv">i_CmdSelectSpeed</span> : <span class="nv">INT</span> :<span class="o">=</span> <span class="mi">0</span><span class="c1">; //CMD: [1,2,3,4] Select which speed for the Motor to run</span> <span class="nv">i_External</span> : <span class="nv">UDT_External</span><span class="c1">; //External input interface</span> <span class="nv">i_SendStatistics</span> : <span class="nv">BOOL</span><span class="c1">; //CMD: Trigger Send and clear statisticals</span> <span class="nv">i_IoNotPecEos</span> : <span class="nv">BOOL</span><span class="c1">; //HW: Fail safe signal of Photo Electric Cell (TRUE=No product detected)</span> <span class="nv">i_IoPpi</span> : <span class="nv">BOOL</span><span class="c1">; //HW: The PPI signal</span> <span class="nv">i_IoEncoder</span> : <span class="nv">DINT</span>:<span class="o">=</span> <span class="mi">0</span><span class="c1">; //HW: [mm/sec] encoder displacement</span> <span class="nv">i_LmsBusError</span> : <span class="nv">BOOL</span><span class="c1">; //LMS has an bus error</span> <span class="nv">i_LmsBusNotPresent</span> : <span class="nv">BOOL</span><span class="c1">; //LMS is not accesable on the bus</span> <span class="nv">i_IoLmsAuto</span> : <span class="nv">BOOL</span> :<span class="o">=</span> <span class="nv">TRUE</span><span class="c1">; //HW: switch of the motor equipment is in 'Automatic' position</span> <span class="nv">i_IoLmsHealthy</span> : <span class="nv">BOOL</span> :<span class="o">=</span> <span class="nv">TRUE</span><span class="c1">; //HW: Healthy signal from motor equipment</span> <span class="nv">END_VAR</span> <span class="nv">VAR_OUTPUT</span> <span class="nv">o_TrsStatus</span> : <span class="nv">UDT_StatusTrs01</span><span class="c1">; //Status of transport section</span> <span class="nv">o_IoMtrFwd</span> : <span class="nv">BOOL</span><span class="c1">; //HW: Forward run signal to motor of conveyor</span> <span class="nv">o_IoMtrRev</span> : <span class="nv">BOOL</span><span class="c1">; //HW: Reverse run signal to motor of conveyor</span> <span class="nv">o_IoSpeedSelect1</span> : <span class="nv">BOOL</span><span class="c1">; //HW: Speed combination bit-1</span> <span class="nv">o_IoSpeedSelect2</span> : <span class="nv">BOOL</span><span class="c1">; //HW: Speed combination bit-2</span> <span class="nv">o_ReadyToRestart</span> : <span class="nv">BOOL</span><span class="c1">; //Ready To Restart from system control</span> <span class="nv">o_TrackMonitor</span> : <span class="nv">UDT_TrackStatistical</span><span class="c1">; //ST: Monitor tracking data</span> <span class="nv">END_VAR</span> </pre></div> <p><img alt="IMG: HalveNamen.PNG" rel="nofollow" src="https://forum.codesys.com//download/file.php?id=4135"/></p></div>