https://forge.codesys.com/forge/talk/Motion/thread/832ecd1468/2024-01-10T20:59:46.907000ZRecent posts to SM Drive license error2024-01-10T20:59:46.907000Z2024-01-10T20:59:46.907000Zeschwellingerhttps://forge.codesys.com/u/eschwellinger/https://forge.codesys.com206dce797dd5eb5a04ec34eea09abca4a69b062d

<div class="markdown_content"><p>goto the licensing metrix tab in CODESYS an check which license ...or send us a screenshot of it here</p></div>

2024-01-10T20:03:37.218000Z2024-01-10T20:03:37.218000Zforesthttps://forge.codesys.com/u/forest/https://forge.codesys.comb1c6708c69f9d998bbac0023638466d7349f512c

<div class="markdown_content"><p>Hi, when it comes about license, I used INVTmatic Studio, which uses Codesys, for programming INVT plc. I bought Codesys Modbus license, it was not expensive, and then realised that INVT didn't have License Manager option (greyed out in program) which is needed for using of Codesys License. <br/> I contacted support from INVT, but developers told me that option is still not available. So depending on environment for programming Codesys, you can or not use Modbus license.</p> <p>Good thing about this version of Modbus TCP it works both direction. I could send commands and receive feedbacks from drive. But communication stops after 30 mins.</p> <p>So I used simple version of ethernet modbus which is somewhere in INVT or Condesys library (I can check tomorrow) which works only one way. I could send cmd to drive, and control it, but didn't have any feedback, like some readings back in PLC. which is bad, but at least I could start it and it didn't fail after 30 mins.</p></div>

2024-01-10T19:29:59.692000Z2024-01-10T19:29:59.692000Ztobyhttps://forge.codesys.com/u/toby/https://forge.codesys.com37d683f6f4ffd561acd202f40f53efc0d4bd9c5b

<div class="markdown_content"><p>Hi albert1999 and forest, I hope you are well.</p> <p>I too am wondering if you have found any solutions? Im working with a RPi and a Omron R88D-ETH servo amplifier. The SoftMotion is timing out after 30min without the license, but I cant figure out how to license it, and I seem to have some compatibility issues between my RPi license and any SoftMotion licenses. Did you guys have any luck?</p> <p>Thank you very much for any assistance offered.</p> <ul> <li>Toby</li> </ul></div>

2022-08-29T13:22:08.776000Z2022-08-29T13:22:08.776000Zforesthttps://forge.codesys.com/u/forest/https://forge.codesys.combd49372886f4af1b663d3de01a4542f860d5fb88

<div class="markdown_content"><p>Hi, did you solve this thing with license? I have similar issue with modbus tcp slave... I installed license for library but same again.</p></div>

2022-04-17T09:18:21.473000Z2022-04-17T09:18:21.473000Zeschwellingerhttps://forge.codesys.com/u/eschwellinger/https://forge.codesys.com35c502e6230a162849a1cda2f18c30416dc8a42b

<div class="markdown_content"><ul> <li>do not execute PLC_PRG from two tasks (only Ethercat if the motion fb's are called in PLC_PRG</li> <li>license is needed otherwise it will run for 30minutes</li> <li>check the plclog for the error</li> </ul></div>

2022-04-10T18:28:23.876000Z2022-04-10T18:28:23.876000Zalbert1999https://forge.codesys.com/u/albert1999/https://forge.codesys.com1252dc1defe2e71d973acdd236f5ee2852ed04bf

<div class="markdown_content"><p>Hello.<br/> I am trying to use my servo and servo amplifier from raspberry PI. I use Codesys for raspberry and Ethercat as my communication fieldbus. Servo amplifier is Estun Pronet and servo drive is Estun EMJ-02-ASA22. It applies CiA402 profile.<br/> I have made device configuration in my project, Ethercat communication is running, but I get error in the status of drive saying "There is a configuration error" and sometimes after a few seconds "The license is missing or invalid. The PLC runs in demo mode". What should I do with it? I also need to say that it's my first time work with SoftMotion so I dont know much about it.</p></div>