Using the Wago 750-658 CAN Gateway

2024-07-23T15:11:00.253000Z

I would ask the Wago Support - they have a CODESYS V3 runtime (not eCOCKPIT) which probably support this?

Using the Wago 750-658 CAN Gateway

2024-07-23T12:31:11.526000Z

Is there any solution for this ? or do you need to use wago runtime and use the function blocks for the CanOpen ?

Using the Wago 750-658 CAN Gateway

2024-07-23T12:31:09.678000Z

Is there any solution for this ? or do you need to use wago runtime and use the function blocks for the CanOpen ?

Using the Wago 750-658 CAN Gateway

2024-07-23T12:31:05.297000Z

Is there any solution for this ? or do you need to use wago runtime and use the function blocks for the CanOpen ?

Using the Wago 750-658 CAN Gateway

2023-02-03T18:05:54.924000Z

Hello, 4 years later, is it still the same status for the support of the Wago CAN gateway 750-658? Still no plan to implement this?

Using the Wago 750-658 CAN Gateway

2020-02-27T15:13:01.574000Z

Hi,
well apreciated if you share your solutions or at least code snipets of it.
BR
Edwin

Using the Wago 750-658 CAN Gateway

2020-02-27T15:12:59.768000Z

Hello Edwin

Thank your for your reply, I'll try to order a cable from Wago and run a few tests.

I may order a 750-650 RS-232 module as well and try to get it to work.
I managed to get the 750-651 TTY module to work, and it seems that the 750-650 follows the exact same method of manipulating the control byte to transmit data.

I'll try to follow-up when I'm done, but it will be some time before I've finished testing.

Thank you again Edwin.

Using the Wago 750-658 CAN Gateway

2020-02-27T15:12:59.042000Z

Hi,

sure if you use WAGO 750-8204 and the local CAN it works... only the additional slide is not implemented.
(thought you need a second CAN port/interface)

I just need one CAN connector to send some CAN layer 2 messages to an IFM RTC module
yes should work check the example in the CODESYS Store:
https://store.codesys.com/can-bus-examp ... escription

Zitat:
Also a completely different question:
If I assign the service port to the runtime would I then be able to use this cable for RS-232 communication from CoDeSys 3 https://www.wago.com/us/controllers-bus ... /p/750-920 ?
and in addition use the serial port on the base of the CPU for RS-485 Modbus RTU communication?

Think this might work ( never used it that way) See screenshot
You need to change the setting in the service Interface - then figure out which com port is assigned... maybe a symbolic link is needed

/dev/ttyO is the regular interface you need to add the service interface then to /dev/ttyO +1

assignment:

COM1 – (/dev/ttyO0) Onboard-Sub-D(X3)
COM2 – (/dev/ttyO2) Konfigurations- und Programmierschnittstelle

so you need to change the link /dev/ttyO1 should point to /dev/ttyO2 that in CODESYS the devices are accesible by Com1 and Com2

BR
Edwin

Using the Wago 750-658 CAN Gateway

2020-02-27T15:12:57.185000Z

Hello Edwin

Thank you for your reply, this is unfortunate news.

Would it be different if I selected a CPU with CAN on the CPU module instead of a add-on slide?
for example WAGO 750-8204?

I just need one CAN connector to send some CAN layer 2 messages to an IFM RTC module

Also a completely different question:
If I assign the service port to the runtime would I then be able to use this cable for RS-232 communication from CoDeSys 3 https://www.wago.com/us/controllers-bus ... /p/750-920 ?
and in addition use the serial port on the base of the CPU for RS-485 Modbus RTU communication?

Thanks

Using the Wago 750-658 CAN Gateway

2020-02-27T15:12:56.542000Z

Hi,
no this does not work there is no driver for this available, all these devices which have 'configuration by registers' are hard to use.
Sure with an huge application effort maybe this is possible, but I think it is not easy possible.
There are no plans at the moment to implement this.
The only option to have a second CAN on the PFC's it to use EK1100 and EL6751 Gateway via Ethercat (Beckhoff)
CANopen or J1939
(for 3.5SP14 release this Gateway will even support J1939)

BR
Edwin

Recent posts to Using the Wago 750-658 CAN Gateway

Using the Wago 750-658 CAN Gateway

Using the Wago 750-658 CAN Gateway

Using the Wago 750-658 CAN Gateway

Using the Wago 750-658 CAN Gateway

Using the Wago 750-658 CAN Gateway

Using the Wago 750-658 CAN Gateway

Using the Wago 750-658 CAN Gateway

Using the Wago 750-658 CAN Gateway

Using the Wago 750-658 CAN Gateway

Using the Wago 750-658 CAN Gateway