Welcome to our new forum
All users of the legacy CODESYS Forums, please create a new account at account.codesys.com. But make sure to use the same E-Mail address as in the old Forum. Then your posts will be matched.
Close
Hi,
I using CODESYS Control for PFC200 SL Version: 3.5.16.20
In Wago PFC200 internal bus I try find 750-623 Wago module (Power Supply; 24 V/5 … 15 VDC) and I can't find it.
Why ?
Thanks in advance.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Hi,
i think there is no need to add anything for this, other user report they using
750-602 which is probably similar?
No processdata for this slices...
BR
Edwin
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
let me check.. I even do not find module to attach this in eCOCKPIT. ( Maybe I'm wrong - do now know it very well)
Do you have this in our hands?
Just plug it an give it a try, expect as I told, if it does not have process data so no need to add anything there probably.
Last edit: eschwellinger 2020-09-28
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Hi Edwin,
is the recent 3.5.16.20 runtime compatible with the Wago firmware V030510 (17) on a pfc200 like 750-8212 ?
In the release notes I can only find firmware 16 with 3.5.16.10
Thanks a lot.
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Hi,
basically might work, but I would recommend to update to FW17 (tested and even sucurity updates included) -
you just need to request it on the Wago homepage
- write the image to an SD card
- boot from it
- use the wbm - copy the image to the internal flash
If you would like to refer to this comment somewhere else in this project, copy and paste the following link:
Hi,
I using CODESYS Control for PFC200 SL Version: 3.5.16.20
In Wago PFC200 internal bus I try find 750-623 Wago module (Power Supply; 24 V/5 … 15 VDC) and I can't find it.
Why ?
Thanks in advance.
Hi,
i think there is no need to add anything for this, other user report they using
750-602 which is probably similar?
No processdata for this slices...
BR
Edwin
I don't have 750-602. Please find in attachment.
let me check.. I even do not find module to attach this in eCOCKPIT. ( Maybe I'm wrong - do now know it very well)
Do you have this in our hands?
Just plug it an give it a try, expect as I told, if it does not have process data so no need to add anything there probably.
Last edit: eschwellinger 2020-09-28
verified... no need to add as module in the device tree!
Hi Edwin,
is the recent 3.5.16.20 runtime compatible with the Wago firmware V030510 (17) on a pfc200 like 750-8212 ?
In the release notes I can only find firmware 16 with 3.5.16.10
Thanks a lot.
yes,FW17 have been tested with 3.5.16.20 should work.
Last edit: eschwellinger 2020-09-29
Additional question. I can use Runtime PFC200 3.5.16.20 with Firmware Revision 03.01.07(13) in my PFC200 ?
Hi,
basically might work, but I would recommend to update to FW17 (tested and even sucurity updates included) -
you just need to request it on the Wago homepage
- write the image to an SD card
- boot from it
- use the wbm - copy the image to the internal flash
Ok, in FW17 is the same procedure like in FW13 to run serial COM (Modbus Master) on port 1 and run SMS Communiaction on port 4, by:
add in /etc/CODESYSControl.cfg
[SysCom]
Linux.Devicefile.1=/dev/serial
Linux.Devicefile.4=/dev/ttyRUNTIME66
?