Raspberry Pi MC SL with MCP23017

2023-04-04T09:21:16.418000Z

Nice job, What am I doing wrong here? I added the device and library. When adding the module it says the following.

Raspberry Pi MC SL with MCP23017

2023-01-13T13:46:50.496000Z

Because there is something wrong with the initalization andthe preconfigured values (inputs) from the library are used.

I found solutions for the issue "not being able to change the outputs, before a dump via linux shell":

quick and dirty: change the preconfigured value in the library for your needs. Use 16#FF for Inputs and 16#00 for outputs:

IO_A : BYTE := 16#FF;
IO_B : BYTE := 16#FF;

more usually one: reinitialize the port configuration on request. Add this code in the library to the case structure in the FB:

10:
    IF REINIT THEN
        _iState := 0;
    END_IF

Additionally you have to trigger/request the reinitialization of the configuration after the device is "operational". And if you want to you can change the polarity and wether the Port A/B is configured as input or output during runtime. Add this code or parts of it to your project:
Declaration:

RTRIG_operational: R_TRIG;
xInitialized: BOOL;
xReinitialze: BOOL;
xSwitchIO: BOOL;
xSwitchIO_old: BOOL;
xInputPolarity: BOOL;
xInputPolarity_old: BOOL;

Button_1: BOOL;
Button_2: BOOL;
Button_3: BOOL;
Button_4: BOOL;
Button_5: BOOL;
Button_6: BOOL;
Button_7: BOOL;
Button_8: BOOL;

Rele_1: BOOL;
Rele_2: BOOL;
Rele_3: BOOL;
Rele_4: BOOL;
Rele_5: BOOL;
Rele_6: BOOL;
Rele_7: BOOL;
Rele_8: BOOL;

Code:

RTRIG_operational(CLK:=MCP23017.Operational);

IF NOT xInitialized AND RTRIG_operational.Q THEN
    xReinitialze := TRUE;
    xInitialized := TRUE;
END_IF

IF xSwitchIO <> xSwitchIO_old THEN
    xReinitialze := TRUE;
    xSwitchIO_old := xSwitchIO;
END_IF

IF xInputPolarity <> xInputPolarity_old THEN
    xReinitialze := TRUE;
    xInputPolarity_old := xInputPolarity;
END_IF

IF xReinitialze THEN
    IF NOT xSwitchIO THEN
        MCP23017.IO_A := 16#FF; // Input
        MCP23017.IO_B := 16#00; // Output
    ELSE
        MCP23017.IO_A := 16#00; // Output
        MCP23017.IO_B := 16#FF; // Input
    END_IF
    IF NOT xInputPolarity THEN
        MCP23017.IPOL_A := 16#00;   // Same
        MCP23017.IPOL_B := 16#00;   // Same
    ELSE
        MCP23017.IPOL_A := 16#FF;   // Opposite
        MCP23017.IPOL_B := 16#FF;   // Opposite
    END_IF
    MCP23017.REINIT := TRUE;
    xReinitialze := FALSE;
END_IF

IF NOT MCP23017.REINIT THEN
    IF NOT xSwitchIO THEN
        Button_1 := MCP23017.IN_A.0;
        Button_2 := MCP23017.IN_A.1;
        Button_3 := MCP23017.IN_A.2;
        Button_4 := MCP23017.IN_A.3;
        Button_5 := MCP23017.IN_A.4;
        Button_6 := MCP23017.IN_A.5;
        Button_7 := MCP23017.IN_A.6;
        Button_8 := MCP23017.IN_A.7;

        MCP23017.OUT_B.0 := Rele_1;
        MCP23017.OUT_B.1 := Rele_2;
        MCP23017.OUT_B.2 := Rele_3;
        MCP23017.OUT_B.3 := Rele_4;
        MCP23017.OUT_B.4 := Rele_5;
        MCP23017.OUT_B.5 := Rele_6;
        MCP23017.OUT_B.6 := Rele_7;
        MCP23017.OUT_B.7 := Rele_8;
    ELSE
        MCP23017.OUT_A.0 := Rele_1;
        MCP23017.OUT_A.1 := Rele_2;
        MCP23017.OUT_A.2 := Rele_3;
        MCP23017.OUT_A.3 := Rele_4;
        MCP23017.OUT_A.4 := Rele_5;
        MCP23017.OUT_A.5 := Rele_6;
        MCP23017.OUT_A.6 := Rele_7;
        MCP23017.OUT_A.7 := Rele_8;

        Button_1 := MCP23017.IN_B.0;
        Button_2 := MCP23017.IN_B.1;
        Button_3 := MCP23017.IN_B.2;
        Button_4 := MCP23017.IN_B.3;
        Button_5 := MCP23017.IN_B.4;
        Button_6 := MCP23017.IN_B.5;
        Button_7 := MCP23017.IN_B.6;
        Button_8 := MCP23017.IN_B.7;
    END_IF
END_IF

I tested this positively with the old library (posted from eschwellinger at 2021-11-27 https://forge.codesys.com/forge/talk/Runtime/thread/8981ce928a/?page=1&limit=25#1cc1) and with the new library (posted from elconfa at 2019-01-10 https://forge.codesys.com/forge/talk/Runtime/thread/a2dd4dd45f/#774c). Finally, I extended the new library so that the polarity switching of the inputs can be controlled with a variable:
Declaration:

IPOL_A: BYTE := 16#00;  // Port A configuration: 0=same/1=opposite (INPUT POLARITY PORT REGISTER)
IPOL_B: BYTE := 16#00;  // Port B configuration: 0=same/1=opposite (INPUT POLARITY PORT REGISTER)

Code:

STATE := STATE AND write8(16#02,IPOL_A);    //  IPOL: INPUT POLARITY PORT REGISTER
                        //      1=GPIO register bit reflects the opposite logic state of the input pin.
                        //      0=GPIO register bit reflects the same logic state of the input pin.
STATE := STATE AND write8(16#03,IPOL_B);    //  IPOL: INPUT POLARITY PORT REGISTER
                        //      1=GPIO register bit reflects the opposite logic state of the input pin.
                        //      0=GPIO register bit reflects the same logic state of the input pin.

Raspberry Pi MC SL with MCP23017

2020-09-17T06:19:44.368000Z

Hello,

I have used this library and this example to use the MCP23017 as digital outputs, but there is no change on IO pins when I change the state (always 5V on pins).

Why is there no change on pins?

Regards

Raspberry Pi MC SL with MCP23017

2020-02-27T15:31:53.933000Z

Sorry I forgot my Codesys code:
MCP23017_0x24.OUT_A:=16#00; //Porta --> Output
MCP23017_0x24.OUT_B:=16#FF; //PortB --> Input
GVL.xPB:=MCP23017_0x24.IN_B.0;

IF NOT GVL.xPB THEN
MCP23017_0x24.OUT_A.0:=TRUE;
MCP23017_0x24.OUT_A.1:=TRUE;
MCP23017_0x24.OUT_A.2:=TRUE;
MCP23017_0x24.OUT_A.3:=TRUE;
MCP23017_0x24.OUT_A.4:=TRUE;
MCP23017_0x24.OUT_A.5:=TRUE;
MCP23017_0x24.OUT_A.6:=TRUE;
MCP23017_0x24.OUT_A.7:=TRUE;
END_IF

IF GVL.xPB THEN
MCP23017_0x24.OUT_A.0:=FALSE;
MCP23017_0x24.OUT_A.1:=FALSE;
MCP23017_0x24.OUT_A.2:=FALSE;
MCP23017_0x24.OUT_A.3:=FALSE;
MCP23017_0x24.OUT_A.4:=FALSE;
MCP23017_0x24.OUT_A.5:=FALSE;
MCP23017_0x24.OUT_A.6:=FALSE;
MCP23017_0x24.OUT_A.7:=FALSE;
END_IF

Raspberry Pi MC SL with MCP23017

2020-02-27T15:31:53.236000Z

Hello
from time to time I trying to work with the MCP23017. I have no problem to use the MCP ports as inputs but until now I was not able to use the MCP ports as outputs (e.g. to control a LED).
Regards
JJoe

Raspberry Pi MC SL with MCP23017

2020-02-27T15:31:52.541000Z

Hi,
no mapping is needed for I2C on the GPIO's.
Did you enable I2C by using CLI?

sudo raspi-config
That's basically the only thing which is needed.

You could check your device by:
i2cdetect -y 1
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
If this works CODESYS should work with the I2C too.

BR
Edwin

Raspberry Pi MC SL with MCP23017

2020-02-27T15:31:50.458000Z

Hello everyone,

Sorry for my late response - hope you all had a lovely Christmas.

Yes I downloaded that driver, library and sample code from that thread Edwin but I was not able to get any response. I think I am missing something trivial but such as setting the GPIO to an input/output but I am not able to see the i2c gpio in codesys. Is this correct?

If anyone has 30 minutes (or any time at all) to have a quick run through of what I have already done and give some advice I would greatly appreciate it.

I look forward to hearing from you

Raspberry Pi MC SL with MCP23017

2020-02-27T15:31:49.614000Z

Hi,
you could give the driver from the section here a try:
l viewtopic.php?f=23&t=5872 l
or is it what you have already done?

This section will move to forge too...next
BR
Edwin

Raspberry Pi MC SL with MCP23017

2020-02-27T15:31:48.816000Z

Hello, in my brief search I couldn't find your exact Codesys driver.

You can make your own though, here is the documentation.
https://forge.codesys.com/drv/io-drivers/doc/I2C/

If you decide to develop your driver on forge.codesys.com, there is a wonderful community to help when you are stuck.

Let me know if there are any specific questions about the process, or of course you can ask there.

Raspberry Pi MC SL with MCP23017

2020-02-27T15:31:46.865000Z

Originally created by: phenixrb

hello oliver,
Codesys does not manage MCP23017 in I2C, but MCP23S17 in SPI.

l viewtopic.php?f=23&t=6247 l

Recent posts to Raspberry Pi MC SL with MCP23017

Raspberry Pi MC SL with MCP23017

Raspberry Pi MC SL with MCP23017

Raspberry Pi MC SL with MCP23017

Raspberry Pi MC SL with MCP23017

Raspberry Pi MC SL with MCP23017

Raspberry Pi MC SL with MCP23017

Raspberry Pi MC SL with MCP23017

Raspberry Pi MC SL with MCP23017

Raspberry Pi MC SL with MCP23017

Raspberry Pi MC SL with MCP23017