Error when opening CAN handle with library

2020-02-27T16:31:14.891000Z

Today I installed the Codesys package V3.5.9.40 en now the CAN bus isfunctioning when 2 CAN overlays are loaded.

Error when opening CAN handle with library

2020-02-27T16:31:14.033000Z

I tried several settings in the config.txt and interfaces files but cannot find a solution. The strange phenomena is that ifconfig can0 shows that messages are coming in and that Codesys is not seeing any messages with 2 CAN overlays loaded. With 1 CAN overlay loaded everything is fine.

It looks that the problem is inside the Codesys run-time.

Error when opening CAN handle with library

2020-02-27T16:31:13.186000Z

In my setup I have two Raspberry Pi 3, both with CanberryDual. I could not get CANopen working from CODESYS, but after trying your tip of only adding the first CAN overlay it now works! If anyone has some clue or directions how to get it working with both CAN ports, it would be very welcome!

Error when opening CAN handle with library

2020-02-27T16:31:10.750000Z

Thanks for the tip. We already tried to add that setting to the config.txt maar it does not help anything. We get messages in Linux when we look with ifconfig. We only do NOT get the CAN messages in Codesys. When we use 1 can layer it is functioning. It does not function with two layers loaded.

Error when opening CAN handle with library

2020-02-27T16:31:09.892000Z

in config .txt put
dtparam=spi=on
dtoverlay=mcp2515-can0,oscillator=16000000,interrupt=23
dtoverlay=mcp2515-can1,oscillator=16000000,interrupt=24

i must to verified the oscillator fervency
this setting is for last Linux kernel

Error when opening CAN handle with library

2020-02-27T16:31:07.461000Z

I found the reason of the problem. When I load both can0 and can1 overlays in de config.txt than it will not function anymore. With only the can0 overlay loaded everything works fine.

I have two mcp2515 chips added to the system, on interrupt 23 and 24. With the Pi B+ I had no problem. Now I have the Pi 3 and it does not work anymore for 2 can busses.

Error when opening CAN handle with library

2020-02-27T16:31:06.606000Z

!/bin/sh

BITRATE=expr $2 \\* 1000
ifconfig $1 down
echo ip link set $1 type can bitrate $BITRATE
ip link set $1 type can bitrate $BITRATE
ifconfig $1 up

Error when opening CAN handle with library

2020-02-27T16:31:05.754000Z

Have you test baudrate=16#1400 (1 MHz). The codes which expects by sja1000.

Error when opening CAN handle with library

2020-02-27T16:31:03.317000Z

I found in the Codesyscontrol.log an error about the rts_set_baud.sh:

1474024643: Cmp=CM, Class=1, Error=0, Info=10, pszInfo= System: <cmp>SysMem</cmp>, <id>0x00000108</id> <ver>3.5.8.10</ver>
1474024643: Cmp=CM, Class=1, Error=0, Info=10, pszInfo= System: <cmp>SysOut</cmp>, <id>0x0000010b</id> <ver>3.5.8.10</ver>
1474024643: Cmp=CM, Class=1, Error=0, Info=10, pszInfo= System: <cmp>SysModule</cmp>, <id>0x000001.//rts_set_baud.sh: 3: .//rts_set_baud.sh: ./pcan: not found
09</id> <ver>3.5.8.10</ver>
1474024643: Cmp=CM, Class=1, Error=0, Info=10, pszInfo= System: <cmp>SysCom</cmp>, <id>0x00000100</id> <ver>3.5.8.10</ver>
1474024643: Cmp=CM, Class=1, Error=0, Info=10, pszInfo= System: <cmp>SysDir</cmp>, <id>0x0000011b</id> <ver>3.5.8.10</ver>
1474024643: Cmp=CM, Class=1, Error=0, Info=10, pszInfo= System: <cmp>SysEvent</cmp>, <id>0x00000102</id> <ver>3.5.8.10</ver>
1474024643: Cmp=CM, Class=1, Error=0, Info=10, pszInfo= System: <cmp>SysInternalLib</cmp>, <id>0x00000107</id> <ver>3.5.8.10</ver>
1474024

We use the MCp2515 cjip connected via the SPI interface. I think we need to change this file.

#!/bin/sh
CAN_NUM=$(echo $1 | sed 's,^can([0-9]).,\1,')
./pcan /dev/pcanusb$CAN_NUM $2

Any help will be highly appreciated!

Error when opening CAN handle with library

2020-02-27T16:31:02.425000Z

With The B+ model I could use this code for opening a CAN handle with the CL2 library. Since I migrated for our test system to model 3B it is not functioning anymore. When opening the handle there is an error. I am using the lastest versions 3.5.9.30. On the Pi is the package 3.5.9.20.

IF (hDriver = CAA.gc_hINVALID) THEN
    hDriver := CL2.DriverOpenH( usiNetId        := usiNetwork, 
                        uiBaudrate      := uiBaudrate, 
                        xSupport29Bits  := xSupport29Bits, 
                        ctMessages      := ctMessages, 
                        peError     := ADR(eErrorInternal));

I always get eErrorInternal = 1. This number is not in te list of errors. The errors list is starting from 10xxx.

I hope someone has a clue to fix this problem.

Recent posts to Error when opening CAN handle with library

Error when opening CAN handle with library

Error when opening CAN handle with library

Error when opening CAN handle with library

Error when opening CAN handle with library

Error when opening CAN handle with library

Error when opening CAN handle with library

Error when opening CAN handle with library

!/bin/sh

Error when opening CAN handle with library

Error when opening CAN handle with library

Error when opening CAN handle with library