Activity for omiidlahttps://forge.codesys.com/u/omiidla/activity/2022-02-21T18:46:06.285000ZRecent activity for omiidlaomiidla posted a comment on discussion Runtime 🇬🇧2022-02-21T18:46:06.285000Z2022-02-21T18:46:06.285000Zomiidlahttps://forge.codesys.com/u/omiidla/profile/https://forge.codesys.com/forge/talk/Runtime/thread/7bd10254af/?limit=25#3a6eI've been using various versions of these IFM AL modules, to varying levels of success. A few notes. Before SP17P2 the Profinet overhead was rather greedy and caused all sorts of problems in the soft controllers we used. I highly recommend using the 4.2.0.0 or 4.2.1.0 version if you're planning on using the Profinet master stack. Profinet_CommunicationTask can be slowed down - it's acyclic less important stuff. Profinet_IOTask running on recommended interval 1ms pre-4.2.0 ate all my resources. After...omiidla modified a comment on discussion Engineering 🇬🇧2021-09-03T15:12:20.759000Z2021-09-03T15:12:20.759000Zomiidlahttps://forge.codesys.com/u/omiidla/profile/https://forge.codesys.com/forge/talk/Engineering/thread/2ac5a50967/?limit=25#ce84Before you build your project again, in Device window open the PLC Settings tab. Select Enabled 1 or Enabled 2 under Always update variables. You now should be able to see your I/O when going online.omiidla posted a comment on discussion Engineering 🇬🇧2021-09-03T15:11:28.635000Z2021-09-03T15:11:28.635000Zomiidlahttps://forge.codesys.com/u/omiidla/profile/https://forge.codesys.com/forge/talk/Engineering/thread/2ac5a50967/?limit=25#ce84Before you build your project again, in Device window open the PLC Settings tab. Select Enabled 1 or Enabled 2 under Always update variables. You now should be able to see your I/O when going online.omiidla posted a comment on discussion Engineering 🇬🇧2021-09-02T16:11:38.104000Z2021-09-02T16:11:38.104000Zomiidlahttps://forge.codesys.com/u/omiidla/profile/https://forge.codesys.com/forge/talk/Engineering/thread/93bc9ccba9/?limit=25#9114That seems to have worked, thanks!omiidla modified a comment on discussion Engineering 🇬🇧2021-09-01T16:57:13.630000Z2021-09-01T16:57:13.630000Zomiidlahttps://forge.codesys.com/u/omiidla/profile/https://forge.codesys.com/forge/talk/Engineering/thread/93bc9ccba9/?limit=25#cd49Hi, I'm running a (v 3.5.17.0) compiler on Phoenix-Contact PLCNext 2152/2404267 (Codesys control for PLCNext v4.1.0.0, using 2021.0 LTS firmware) as an ETHERCAT master. The system also uses an extension module for the additional network interface (AXC F XT ETH 1TX/2403115, Intel I210 based). If i use eth0 or the primary network interface as the Ethercat master, everything is running fine, my existing Ethercat devices are found and accessible. If i switch the master to use enp1s0 - the network interface...omiidla posted a comment on discussion Engineering 🇬🇧2021-09-01T16:14:12.801000Z2021-09-01T16:14:12.801000Zomiidlahttps://forge.codesys.com/u/omiidla/profile/https://forge.codesys.com/forge/talk/Engineering/thread/93bc9ccba9/?limit=25#cd49Hi, I'm running a (v 3.5.17.0) compiler on Phoenix-Contact PLCNext 2152/2404267 (Codesys control for PLCNext v4.1.0.0, using 2021.0 LTS firmware) as an ETHERCAT master. The system also uses an extension module for the additional network interface (AXC F XT ETH 1TX/2403115, Intel I210 based). If i use eth0 or the primary network interface as the Ethercat master, everything is running fine, my existing Ethercat devices are found and accessible. If i switch the master to use enp1s0 - the network interface...