https://forge.codesys.com/u/rpiautomation12/activity/2020-10-22T03:20:16.182000ZRecent activity for rpiautomation122020-10-22T03:20:16.182000Z2020-10-22T03:20:16.182000Zrpiautomation12https://forge.codesys.com/u/rpiautomation12/profile/https://forge.codesys.com/forge/talk/Engineering/thread/a45c28372c/?limit=25#7ff7

Hi. I tested your recommendation (to use GPIO B+/Pi2) but still all the GPIO pins are initially in TRUE value after running the program. See attached picture. Thanks :))

2020-10-22T01:13:14.901000Z2020-10-22T01:13:14.901000Zrpiautomation12https://forge.codesys.com/u/rpiautomation12/profile/https://forge.codesys.com/forge/talk/Engineering/thread/a45c28372c/?limit=25#315e

ok.. this will help me a lot. thank you very much sir!!. will delete the other thread.

2020-10-21T02:01:42.612000Z2020-10-21T02:01:42.612000Zrpiautomation12https://forge.codesys.com/u/rpiautomation12/profile/https://forge.codesys.com/forge/talk/Engineering/thread/4d9d5df095/?limit=25#a6db

i was wondering if my new raspberry pi 4 is supported by codesys rpi control. i've seen many videos on youtube with codesys using raspberry pi as PLC.

2020-10-21T01:46:08.165000Z2020-10-21T01:46:08.165000Zrpiautomation12https://forge.codesys.com/u/rpiautomation12/profile/https://forge.codesys.com/forge/talk/Runtime/thread/622bd04f6e/?limit=25#03ac

what do you mean by project archive sir? i recently uploaded my files on the same thread under engineering forum, here's the link : https://forge.codesys.com/forge/talk/Engineering/thread/a45c28372c/

2020-10-20T00:41:57.657000Z2020-10-20T00:41:57.657000Zrpiautomation12https://forge.codesys.com/u/rpiautomation12/profile/https://forge.codesys.com/forge/talk/Engineering/thread/a45c28372c/?limit=25#2170/1ec2

Is this the files you needed sir? thanks in advance for your help sir

2020-10-19T02:27:49.163000Z2020-10-19T02:27:49.163000Zrpiautomation12https://forge.codesys.com/u/rpiautomation12/profile/https://forge.codesys.com/forge/talk/Engineering/thread/a45c28372c/?limit=25#87b7

Hi, i have a problem. All my GPIO pins of my raspberry pi 4 model B are always TRUE when the ladder program i created is running. See picture attached. I created a simple normally open contact in series with a coil but it turns out that my normaly open contact is having TRUE value all the time when i run the program.. Please i need help :(

2020-10-19T01:37:22.632000Z2020-10-19T01:37:22.632000Zrpiautomation12https://forge.codesys.com/u/rpiautomation12/profile/https://forge.codesys.com/forge/talk/Runtime/thread/622bd04f6e/?limit=25#1bf4

Hi, i have a problem. All my GPIO pins of my raspberry pi 4 model B are always TRUE when the ladder program i created is running. See picture attached. I created a simple normally open contact in series with a coil but it turns out that my normaly open contact is having TRUE value all the time when i run the program.. Please i need help :(