Post by mosayeb on Power off ^{CODESYS Forge talk (Post)}
Hello. It is interesting that almost everyone has faced this problem. Run the program as shown in the attached photo. Give True to the Enable input and change the status of the drive to on and off with Servo-On
Last updated: 2024-04-08

Post by flavinhofh on Beaglebone Black OPC-UA Server ^{CODESYS Forge talk (Post)}
ah ok, I will keep trying, I already removed all security from the Server side. I'm new on codesys and I don't know yet how to implement the certificates, but I will find out and also try. thanks for your reply.
Last updated: 2024-04-11

Post by joschi2804 on Licensing info not available. ^{CODESYS Forge talk (Post)}
Hello, I've added some additional log output. Maybe this helps in figuring out the root cause. I've turned logging and verbose mode on for the CodeMeterLin application and I get the error, that some entry is not found.
Last updated: 2024-04-11

Post by ademarvribeiro on warning message ^{CODESYS Forge talk (Post)}
this mean your project dont have compile information. try to upload code from PLC and them go online. To know the differences between online program and your project clica in Details, when the message pop-up.
Last updated: 2024-04-14

Post by damian177 on Raspbery Pi and Calendar ^{CODESYS Forge talk (Post)}
Hi, In my visualisation I have a "Calendar" control. I would like save day and month which will be clicket by operator on this control . forexample save in string array. How do this ?
Last updated: 2024-04-23

Post by cpoi on Safety EL6900 com Error ^{CODESYS Forge talk (Post)}
Hello, I using the EL6900 module with EL 1904 and EL2904 on Ethercat, and I have a ComErr on the EL6900. The FSoE Adresse : EL6900 = 1 EL1904 = 11 EL2904 = 15 Any suggestion? Thanks a lot in advance.
Last updated: 2024-04-26

Post by radekkoza on How to use GPIO (and IOT2000 IO-Module) with CODESYS Control for IOT2000 SL ? ^{CODESYS Forge talk (Post)}
Hi I have this question I can't find anywhere what pins Di3 and Di4 have all the rest work . I have a 10 input iot2000 card
Last updated: 2024-05-05

Post by radekkoza on How to use GPIO (and IOT2000 IO-Module) with CODESYS Control for IOT2000 SL ? ^{CODESYS Forge talk (Post)}
Hi I have this question I can't find anywhere what pins Di3 and Di4 have all the rest work . I have a 10 input iot2000 card
Last updated: 2024-05-05

Post by radekkoza on How to use GPIO (and IOT2000 IO-Module) with CODESYS Control for IOT2000 SL ? ^{CODESYS Forge talk (Post)}
Hi I have this question I can't find anywhere what pins Di3 and Di4 have all the rest work . I have a 10 input iot2000 card
Last updated: 2024-05-05

Post by pasillalej on No gateway with the given settings could be found ^{CODESYS Forge talk (Post)}
Go to Online>Communication Parameters...>Gateway>TCP/IP> Click on "New..." and reestablish your connections with whatever IP address and set up information you have. Bypass whatever is necessary as you may have to redownload to the PLC.
Last updated: 2024-05-09

Post by davidbo on What is the prerequisites for a Raspberry Pi to work with SysSockSetIpAddressAndNetMask() ^{CODESYS Forge talk (Post)}
I have now and it works. I had the idea that it had something to do with codesyscontrol.cfg, but where can I find a description of all the things you can set in codesyscontrol.cfg and its syntax?
Last updated: 2025-11-12

Post by micik on Error, visualisation property handling, VISU_USEPROPERTYINFO ^{CODESYS Forge talk (Post)}
@davidking, can you be more specific about where exactly "Compiler Defines" is located. I'm using Codesys v3.5 SP21 Patch2 and cannot find this Compiler Defines option. In the menu Project -> Project Settings there are Compiler options and Compiler warnings, but that is not it.
Last updated: 2025-11-26

Post by davidbo on License problem with Raspberry Pi ^{CODESYS Forge talk (Post)}
To simplify your problem you shall not select dongle and get dongle errors. Do as shown In some cases you need 2 different licenses depending on the metrics. And yes the system gives not always give proper error messages when you try to reinstall a license
Last updated: 2025-12-01

Post by kenth1973 on MC_Phasing state explenation ^{CODESYS Forge talk (Post)}
Hi George. Thx for the info and recommendation - the robot is running production at customer. But - would you have any information about the states numbers and their different explenations?
Last updated: 2025-12-11

Post by mariusz997 on Visualisation - internal error ^{CODESYS Forge talk (Post)}
Hi - problem solved. I had 3 version of codesys on system and they didn't like each other. After uninstall all and install again only one version now everything is OK
Last updated: 2025-11-12

Post by tristan on Textfield display problem ^{CODESYS Forge talk (Post)}
Hello Tim, I am using CODESYS Visu V4.8.1.0. It works when I turn off the "Support client animation and overlay of native elements". But if I do that, dialog box moving and other options are also disabled so it is a bit problematic. Thank you for helping.
Last updated: 2025-11-27

Post by martinlithlith on Device User Logon and No device is responding.. Pi4b codesys 3.5 SP19 2 + (64-bit) ^{CODESYS Forge talk (Post)}
Hi! Im slowly starting to loose it and i need som help! After a few night of reading up and testing i´m still stuck as a rock and you guys and girls are my last resort for this project. Basic facts; Win 11 Codesys 3.5 SP19 2 + (64-bit) Raspberry pi 4 model b 2 gb Raspian release 11 aarch64 What keeps me up late at night; Username and Password when trying to connect to device and device only beeing connectable for a few seconds. Some of the things I have tried; Username and passord; Credientials from the raspberry Administrator Administrator admin admin Admin Admin administrator administrator Usernames and passwords that I sometimes use (this was a longshot i know, but i was running out of ideas and energy). :) Epand filesystem, activating i2c, spi, 1-wire I can start the gateway and start the runtime. I cant install the edgearm64, arm64 runtime package eventhough I guess i should, i get code [ERROR] Error output: dpkg: error processing archive /tmp/codesysedge_edgearm64_4.8.0.0_arm64.deb (--install): [ERROR] Error output: package architecture (arm64) does not match system (armhf) [ERROR] Error output: Errors were encountered while processing: [ERROR] Error output: /tmp/codesysedge_edgearm64_4.8.0.0_arm64.deb code as a respons. I have tried to Reset Origin Device - no change. I have tried to remove the /etc/CODESYSControl_User.cfg [CmpUserMgr] but i could not find it and i was not sure if i should add it instead but i did not want to mess somthing up. I have tried to create a second gateway with the specific ip if the pi, that did not help. Could it be that i´m currently connected to the pi through WIFI? I can ping the pi and I can connect and control it through VNC. When i scan to select gateway target (scan edge gateway) i find 17-21 devices but can find the pi throug the mac adress. I started of trying to use the "CODESYS Control for Raspberry Pi SL" (I have a license sience earlier) as i read somewhere that this could be used on a Pi4 as well but now i´m trying with the MC SL, no changes, same problem. Right now - gateway version 4.8.0.0 (edgearmHF, armhf), Runtime Package 4.5.0.0 (raspberry, armhf). Any sugestions are very welcome! As mentioned above, theese are some of the things that i have tried/done - but i have been going at this for a while. Best, Martin
Last updated: 2023-09-10

Post by cfam on Codesys Control for PLCnext SL, Bus not running ^{CODESYS Forge talk (Post)}
Good day I would appreciate it if you can give me some advice on how to fix my "Bus Not Running Error". I am Using Codesys 3.5 SP20 and Codesys Control PLCnext SL V4.12.0.0. Codesys control was installed on the device and I can log into it but it seems that it does not pick up the PLC or the IO attached (Please see attached Image). The Bus Cycle Task of the AXL F 2152 is set to Main Task and the "Always update Variable" is Enabled on each IO Module. My Main Task interval is set to 100ms and Priority is set to 0. I have tried other options and none seem to work. Your response to this issue will be highly appreciated.
Last updated: 2024-08-12

Post by cfam on Codesys Control for PLCnext SL, Bus not running ^{CODESYS Forge talk (Post)}
Good day I would appreciate it if you can give me some advice on how to fix my "Bus Not Running Error". I am Using Codesys 3.5 SP20 and Codesys Control PLCnext SL V4.12.0.0. Codesys control was installed on the device and I can log into it but it seems that it does not pick up the PLC or the IO attached (Please see attached Image). The Bus Cycle Task of the AXL F 2152 is set to Main Task and the "Always update Variable" is Enabled on each IO Module. My Main Task interval is set to 100ms and Priority is set to 0. I have tried other options and none seem to work. Your response to this issue will be highly appreciated.
Last updated: 2024-08-12

Post by andrebrandt on FB string and naming ^{CODESYS Forge talk (Post)}
Thank you so much. This worked. Waht im trying to do here is to automatically tag each sensors, valves and so on. There is a preatty nasty tag system i working on. "_320" is not alloved. I can have a tag "+4f=320.004-RT001V" In codesys I want to build the FB in folders. -4f | --320 | --001 This is the system structure. Inside here is all of the sensors and so on. But with Codesys, I cannot tag this like this. So what I'm trying to do now is to Make a folder for the building "4f" and one for the system "320", and a POU _001. Is there a way in init to get folder names?
Last updated: 2024-10-01

Post by andrax on CodeSys Raspberry pi I2C driver not found ^{CODESYS Forge talk (Post)}
Ok, with debug you suppress the errors, but that doesn't help you any further. You can find information about the missing drivers here https://forge.codesys.com/forge/talk/Runtime/thread/8981ce928a/ and here https://github.com/stefandreyer/I2C-Multiplex I'll have to have another look at which library you need. But you can easily find out. Create a completely empty project and insert the TCA9548. You don't need the board. Then look in the library and resolve all conflicts If you can compile the project without errors, delete the TCA9548 and insert the ADS1115. The driver should then also run. Small bonus: with the TCA9548 you can expand your network as you wish and use identical sensors multiple times
Last updated: 2024-11-08

Post by imdatatas on MC_CamIn did not work properly with SMC_FreeEncoder on SoftMotion 4.17.0.0 ^{CODESYS Forge talk (Post)}
Hi @tk096, Thank you for your response. Here is example project file and some screenshot for your analysis regarding this matter. In order to reproduce the problem on your side and make it independent of the hardware, I simulated the encoder counter incrementally for the master in this example. I configured a virtual axis as the slave motion axis. The problem occurs in the same way in the real hardware configuration (servo drive connected to Ethercat and hardware incremental encoder) in MC_CamIn. I hope this example helps you see the problem on your side and understand and find the source of the problem with FreeEncoderAxis for Softmotion 4.17.0.0. Best Regards, Imdat
Last updated: 2024-12-19

Post by matthew on High resolution displays with 150% scaling causes CodeSys IDE to be blurry ^{CODESYS Forge talk (Post)}
I have just upgraded my laptop which has a high res display 2560x1600 and I have to have scaling switch on at 150% but everything looks blurry and not crisp, It seems CodeSys IDE is the only software on my system to look this bad, if I switch to 100% it's crisp but way to small. From a bit of research this could be due to the use of old windows forms or something? I have found a temp workaround that sort of works but not great. You have to run CodeSys in compatibility mode and adjust the DPI settings, this works ok and the editor is clear and crisp again but the actual tool bars are small like running at 100% Anyone got any tips for running CodeSys on high res displays with scaling?
Last updated: 2025-03-03

Post by eaglealex on Length of string and Array of bytes ^{CODESYS Forge talk (Post)}
Hello! I have tried read a file to the string variable. But I faced a problem - there is about 2800 bytes of information in file, but string have a limit 2393 bytes. I made two variables with same address (for automatic convertion) - string[3000] and array of bytes[1..3000]. And I noticed that array of bytes contains all information from file, but string shows only first 2393 bytes. So I have lost information. Is there really such a limitation? Or I have an error in my program and Codesys 2.3 have no limit for such kind of conversation between string and array of bytes? Thank you very much!
Last updated: 2025-04-01

Post by yang123 on EtherCAT Can't reconnect to servo drive ^{CODESYS Forge talk (Post)}
I am using Ethercat Master 4.6.0.0 and have use the automatic restart slaves feature. But we found of after the Ethercat communication normal and slave drive power-off and power-on the slave can't reconnect sucess. The PLC Log show the drive was al status "6#34 : Invalid DC Timeout Error" and its was reconnection sucess first but seconced later the drive will show the "16#2C : Fatal Sync error" and then drive will can't reconnection. Other slave are reconnect sucess which was link after the can't reconnect's drive the drive was OMRON R88D-1SN
Last updated: 2024-01-23

Sort by relevance or date