Post by mkintegration on Reading Absolute Encoder Position From Yasakawa Drive ^{CODESYS Forge talk (Post)}
I am looking to read in the absolute position of a yaskawa servo drive Sigma 7 that is using absolute encoder. It looks like yaskawa outputs this across there CN1 I/O connecter and during operation just outputs encoder pulses. But at boot up transmits the Multiturn data position and the Position within one rotation (pulse train) on two different wires. Once the drives are enabled it just uses incremental pulses. Does any one have experience with what IEC blocks to use to read this information in. I attached the Yaskawa Manual section that talks about the format.
Last updated: 2025-02-26

Post by mkintegration on Reading Absolute Encoder Position From Yasakawa Drive ^{CODESYS Forge talk (Post)}
I am looking to read in the absolute position of a yaskawa servo drive Sigma 7 that is using absolute encoder. It looks like yaskawa outputs this across there CN1 I/O connecter and during operation just outputs encoder pulses. But at boot up transmits the Multiturn data position and the Position within one rotation (pulse train) on two different wires. Once the drives are enabled it just uses incremental pulses. Does any one have experience with what IEC blocks to use to read this information in. I attached the Yaskawa Manual section that talks about the format.
Last updated: 2025-02-26

Post by tyleretn on Codesys 3.5 SP18 P4 Freezing on Library Update ^{CODESYS Forge talk (Post)}
I have created a library with both code and visualizations to be used in multiple other projects. After I update the library version into the library repository, I have much difficulty updating the version into the main project. I can always update the library version in the Library Manager just fine. My issue, is sometimes Codesys will freeze when opening the visualization that uses the library visualizations. Sometimes it opens, but freezes when I try to access the library visualizations from the Visualization Toolbox. I try letting Codesys run for upwards of 4+ hours and it is stuck in this state. On very rare cases I have no issues and can continue with my work. I haven't found a consistent reason or work around. Has anyone else had this happen?
Last updated: 2025-02-27

Post by timvh on Problem Reading Registers via Modbus from non Codesys device ^{CODESYS Forge talk (Post)}
According to the documentation: https://wiki.teltonika-networks.com/view/RUT956_Modbus You need to create a Channel to read 2 registers from address 143 to get the lattitude. It doesn't specify if you need to read it as a Holding Register or as an Input Register. You could try both. So in the Teltonika router, you need to enable it as being a Modbus Server. Then in CODESYS add an Ethernet Adapter, then a Modbus Client (Master) and to the Client (Master) add the Modbus Server (Slave). Set the IP address and add the Channel. The please consider that CODESYS doesn't update any variables when they are not used in the application. In the I/O mapping tab of your I/O configuration, you can set the "Always update" to enabled.
Last updated: 2025-03-08

Post by struccc on Problem Reading Registers via Modbus from non Codesys device ^{CODESYS Forge talk (Post)}
Hi, Might be a good idea first to try out the connection and the device with some handy software, like Modbus Poll. There you can see better, what's really going on... - Is it really connected? - What error code does it return? - Can it read from the register address? - Maybe try Input registers and Holding Registers - can make a difference - Sometimes register addresses are messed up: shifted +-1 (mixing of 2 standards) - Sometimes register addresses start with offset 30000, 40000 ... - Are you using the right protocol? - Is it RTU or TCP? Maybe ASCII? - Can even have a look at the data packets, etc... All this is easier to figure out first with some modbus utility... and then to set it up in CODESYS should not be an issue. P.
Last updated: 2025-03-09

Post by hemuv on Dialog Open ^{CODESYS Forge talk (Post)}
I'm programming an HMI for a machine. I want to log all the parameter's changes (used text field for displaying and changing) for particular User levels. Created a Numpad and want to log oldvalue and Newvalue on 'ok' Button press. To retrieve the oldvalue, i check if the dialogue opened is my Numpad, Then I retrieve the dialogue interface via GetDialogInterface(ADR(myNumpad)) --> numpadData.stVariableValue which contain my oldvalue and save it locally. Problem is sometimes i retrieve the data and sometimes not. Also observed when Numpad Dialogue is Opened, VisuDlgUtil_IsDialogOpen returns False in some cycles.Attached you will find my Project. please let me know what went wrong or if there is a better approach to collect old and New Value of a textfield. Thank you.
Last updated: 2025-03-26

Post by spiessli on Objects in OPC UA Information Model ^{CODESYS Forge talk (Post)}
Hi, I have an OPC UA information model with objects defined in it. I can import the model and use the data types defined in it and create instances of these types. These instances are accessible at Root > Objects > DeviceSet > CODE[...] > Resources > Application > GlobalVars > OPC_UA_Symbols for created instances and at [...] > Programs > PLC_PRG for mapped instances. The object defined in the information model is accessible in UA Expert by the name I have defined in the information model (Manipulator) at Root > Objects > Manipulator. How can I assign values to the Variables defined in the object "Manipulator"? Cheers, spiessli
Last updated: 2025-03-27

Post by elsmart on Sequential read and triggering of Modbs RTU channels in application ^{CODESYS Forge talk (Post)}
Hello I need some help understanding how to use Modbus RTU (COM port) in Codesys enviroment. I defined a Modbus Server device (slave) in device tree and added some channels to read from (function 3). Also I set trigering mode to Application. I have a POU in which I want to trigger each channel one after the other something like this (C code for better visualisation): for (int i = 0; i < channelsCount; i++) { triggerChannel(channelsArray[i]); // Start transmission while(channel.xBusy); // Wait for transmission to complete } I have found ModbusChannel function block documentation but examples are scarce. I don't understand how rising edge triggering works. What would be the best solution for achieving sequntial channel triggering? What is the common way to read multiple Modbus channels once every time a specified POU is executed?
Last updated: 2025-05-16

Post by kut69 on Retain / Persistent Variables in Codesys for Raspberry Pi ^{CODESYS Forge talk (Post)}
Hi, I am interested in details about the .ret file in the filesystem. I have already a project where the file is used (write on demand, read by start) and I want to share it as 'default input' for test devices using the identical application. Opening the .ret file content in a hex editor (I only use a single string retain var) I asked myself what the meaning of the first 24 bytes is. It neither contains a handle to the application nor a reference to the variable. Is this maybe a timestamp? Or a CRC/checksum? Regards, Thomas
Last updated: 2025-05-19

Post by abuckie on Getting raw value as full resolution for ADS1115 ^{CODESYS Forge talk (Post)}
I just found this and I am getting a value larger than 16 bit, around 81000 something. I am reading a 5 volt value and I am using level shifters for the i2c bus. This is how I have the channel configured: ADS1115.usiAddress := 16#48; ADS1115.ChannelConfigs[0].Active := TRUE; ADS1115.ChannelConfigs[0].PGA := FSR_6144mV; ADS1115.ChannelConfigs[0].InputMux := Single_0; RawAnalogValue := ADS1115.Channels[0].Value; It looks like every value is a multiple of 3. Any idea where to look to fix this? I think i found what I want to change in UpdateChannels Channels[FChannelNo].Value := INT_TO_REAL(WORD_TO_INT(LValue) * GetFullScaleRange(ChannelConfigs[FChannelNo].PGA)) / 2048.0; I try to edit it but I can't, sorry if this is a basic question, I am new to CODESYS.
Last updated: 2025-05-22

Post by milan-svarny on ModbusFB.ClientSerial Problem with Reply Timeout ^{CODESYS Forge talk (Post)}
Hi All, I have problem with ModbusFB.ClientSerial. I'm using 4 different port for Modbus communication. After some time of running program ClientSerial stops to receive data to reply buffer and all request finish with Reply Timeout. The Device sent reply correctly,that it is visible on oscilloscope and it is possible to see that data( reply )are in the device. If the usbtty device is read over external app. then it is possible to see all data which were not taken by ModbusFB.ClientSerial. The stack does not overflow or something , program runs correctly forward and no exceptions or something. The main problem it is that when the error occur than it is not possible to reset port or something or maybe i'm doing it wrong way. please help me with this issue. Thank you for any help in advice Milan
Last updated: 2025-05-23

Post by kareem-pt on Velocity is too low even though correct value is reported ^{CODESYS Forge talk (Post)}
Hello, I'm playing around with a single axis. I've setup scaling and set the drive to move 360 degrees in the commissioning tab. The axis does move 360 degrees, but it moves much slower than the 360 degrees per second that I set for the velocity. It seems to be about 3 times slower (taking about 3 seconds instead of 1). This is despite the set and actual velocity both being displayed as 360. The acceleration, deceleration and jerk are all set to very high values. I'm just running this on my PC, using demo mode (no license purchased yet). I've attached a video showing the problem. Does anyone know what the problem could be? Thanks
Last updated: 2025-06-06

Post by viksym on How to get the motor scaling value from code ^{CODESYS Forge talk (Post)}
Is there a way to see what value is set as the "Work travel distance per motor rotation" that is set in the Scaling menu of the axis ? I am working on my own homing function block for sensorless (hardstop) homing and I want to make it be universal between different axes with different motor's scaling for distance per rev so I need to know this value from the axis itself. I know I could do it by just creating an input variable for the function block but I'm leaving that option as a last resort.
Last updated: 2025-06-12

Post by hclai on Maximum Array Index Issue ^{CODESYS Forge talk (Post)}
I was trying to use a table object in visualization. I want to dynamically show the valid rows in the table. However, it does not work when there is 1 row. i put the maximum array index to 1. it does not show the 1st row. when i change to 2, it show the second row only. my project with older visualization profile version is working perfectly fine. I did some test and realized that i must use a Row Selection variable to change from 0 to 1. With this change of Row selection, then the row 1 will show up.
Last updated: 2025-06-19

Post by andrej on Signing of Boot Application for Raspberry Pi ^{CODESYS Forge talk (Post)}
Hello all, I would like to sign my boot application for my Raspberry PI. I generated the X509 Certificate and loaded it to the raspberry. It is successfully displayed as trusted certificate. However, I cannot download and start the Application to the Rasperry, due to a signature mismatch.The error message is rather clear, but I still don’t see how I can fix the issue, since the certificates on the Controller seem to mach the certificate in the user profile. Could you tell me where the error is or which step I am missing. Many thanks and kind regards Andreas
Last updated: 2025-07-17

Post by andrej on Signing of Boot Application for Raspberry Pi ^{CODESYS Forge talk (Post)}
Hello all, I would like to sign my boot application for my Raspberry PI. I generated the X509 Certificate and loaded it to the raspberry. It is successfully displayed as trusted certificate. However, I cannot download and start the Application to the Rasperry, due to a signature mismatch.The error message is rather clear, but I still don’t see how I can fix the issue, since the certificates on the Controller seem to mach the certificate in the user profile. Could you tell me where the error is or which step I am missing. Many thanks and kind regards Andreas
Last updated: 2025-07-17

Post by andrej on Signing of Boot Application for Raspberry Pi ^{CODESYS Forge talk (Post)}
Hello all, I would like to sign my boot application for my Raspberry PI. I generated the X509 Certificate and loaded it to the raspberry. It is successfully displayed as trusted certificate. However, I cannot download and start the Application to the Rasperry, due to a signature mismatch.The error message is rather clear, but I still don’t see how I can fix the issue, since the certificates on the Controller seem to mach the certificate in the user profile. Could you tell me where the error is or which step I am missing. Many thanks and kind regards Andreas
Last updated: 2025-07-17

Post by rer-code on Codesys 3.5.18.60 – Application Loss and Persistent Data Corruption ^{CODESYS Forge talk (Post)}
Hi, I’m currently managing over 50 PLCs running Codesys version 3.5.18.60. At seemingly random intervals, some of these devices experience a failure where: All persistent variables are lost. Attempting to log in results in the message: “The application does not exist on device. Do you want to create it and proceed with download?” The log shows: “Loading retain-data/bootproject failed.” From what I’ve gathered, this may be due to a corrupted persistent data file, but I’m not entirely sure how to confirm or resolve this issue. If anyone has encountered something similar or has suggestions for troubleshooting or preventing this, I would greatly appreciate your input. Best regards
Last updated: 2025-08-19

Post by kporter on High-resolution drive with SoftMotion ^{CODESYS Forge talk (Post)}
I'm beta-testing a new EtherCAT drive for a rotary (modulo) axis in a system where the encoder resolution is 81920000 counts per rotation. If I enter this in the SoftMotion Scaling/Mapping tab for "increments <=> motor turns", I get the error below on the Commissioning tab. Is SM unable to handle a high-resolution encoder? The bus cycle is currently set to the default of 4 msec (Control Win V3 x64), although I plan to reduce that to reduce latency, possibly by switching to the realtime (RT) master. Is SoftMotion incompatible with high-resolution encoders? SMC_CGR_INVALID_POSPERIOD Invalid modulo period (<= 0 or greater than half the bus bandwidth)
Last updated: 2025-08-25

Post by antonz on CoDeSys v3.5: creating libraries for both 32-bit and 64-bit controllers ^{CODESYS Forge talk (Post)}
Follow up question: in the Project Settings, under Library Development, there is an option related to this: Check all Pool Objects -> Pointer size to use Options are: * 32 Bit * 64 Bit * 32 and 64 Bit The descriptions and online help suggest to me this is only relevant for checking and showing any incorrect pointer types as an error in the IDE. E.g. using a DWORD to store a pointer value on a 64-bit controller. It would not control the creation of either 32-bit or 64-bit compiled libraries. Is that correct?
Last updated: 2025-09-01

Post by pernockham on AC Persistence - values are not read from file during start? ^{CODESYS Forge talk (Post)}
I swear I tested this like 20 times yesterday without success. Repeated it today and it works. Maybe the system needed a "real" power reboot? To note. To make a manual edit of a variable I tried some different approaches this is what worked for me. "system/online edited" gvl_var.example_variable REAL:F16#2FFB334H-4 767.7 "manually edited" (with runtime stopped followed by a "cold start" to read from file) gvl_var.example_variable REAL:790.1 (the system will use the manual value but will not set an equivalent "hex" value until next online edit/write cycle)
Last updated: 2025-09-03

Post by davidbo on All the things needed for anonymous login to OPC UA ^{CODESYS Forge talk (Post)}
I thought I knew what I am doing, but something is missing what? From Device-Communication Settings select from drop down menu "Device" Select entry "Change Runtime Security Policy" Check the "Allow anonymous login" Select "Symbol Configuration" in your application In settings check "Support for OPC UA features" Check some of the values you want in your set Press the build button in the "Symbol Configuration" Press the button "Configure Symbol Rights" Make sure that Anonymous_OPCUAServer has access right to your "default set" From Device-Communication Settings select "Access Rights" in RemoteConnections-OPCUAServer Anonymous_OPCUAServer should be given modify and view rights I suppose. I can connect with UaExpert but I cannot see my Application or browse my values. What is missing?
Last updated: 2025-09-10

Post by monteta on Automation without UI ^{CODESYS Forge talk (Post)}
Hello all, there is my problem. i have a project on a PC A who work properly, I aim to take this project and place it on a Pc B with a blank Codesys installed. All seemd to work, the project is created on the PC B, i create my with with online.create_online_application(project.project.active_application) recover my onlineDevice and try onlinedevice.connect() so that i can use create_live_user_management() but then a problem occure on my connect() saying gateway not configured properly. I have setted my set_credentials_for_initial_user(). when i use the Ui, there is absolutely no problem. an other question, is it possible to use the Start and Stop PLC of codesys Control Systray directly in my python script? So that if it detect that it's stopped, then he automatically start it?
Last updated: 2025-09-25

Post by pernockham on *Exception* Async service: ServiceGroup=17, IP=0x5fa45617, Component=CmpSrv ^{CODESYS Forge talk (Post)}
*** The system may be in an inconsistent state, please reboot *** *Exception* Async service: ServiceGroup=17, IP=0x5fa45617, Component=CmpSrv Every time at the instant that I Login to the system a message that the "system may be in an inconsistent state, please reboot" is written in the log. If I logout and repeat login a new entry is set. My system is a "Control for linux SL" running on a debian linux host. Im running it on my desk without any IO attached so message might be caused from that, but I doubt i have seen it before. Rebooting makes no difference. Anyone that have a clue of how I should interpret this error message?
Last updated: 2025-09-26

Post by alexgooi on Licensing info not available. ^{CODESYS Forge talk (Post)}
Dear Forum I have the following config: Codesys_IDE 3.5.20 Codesys_Virtual_Control 4.13 Codesys_License_Server 4.13 I know these are not the newest versions, but in my mind these should work. I have the same problem here. I have the license server installed on the host, and in the docker container(Codesys virtual control) I'm able to ping the license server. In the /conf/codesyscontrol/CODESYSControl_User.cfg I have added the following config: [CmpCodeMeter] EnableNetLicenses=1 LicenseServer.1="ip address of the host" I have tried it via the wbm web-page. I can create new license containers over there, but still no luck. I also have tried to run the docker container with the -s "server_IP" command. I have searched for some tutorial's but I couldn't find it. If anyone has some clue or can give me a push in the right direction it would be very very welcome!
Last updated: 2025-09-29

Sort by relevance or date