Post by ivanmaltar on Update Raspberry Pi error ^{CODESYS Forge talk (Post)}
Hello, from today, I got an error when I try to open 'Tools/Update Raspberry Pi' and I got this error: There is no value with the specified name associated with this subkey. This feature worked before. I did not do any changes to Codesys installation. Codesys version is SP19.1, and CODESYS Control For Raspberry Pi 4.8.0.0
Last updated: 2023-11-30

Post by chirag on About byte swap and convert into 16 bits ^{CODESYS Forge talk (Post)}
Hello, I have %QB0 8 high bits and %QB1 8 low bits . How can i swap bits %QB0 and %QB1 for requirment positions in a 16-bit value ? after that i need %QB0 and %QB1 in to 16bits . For that, i need help. Please see attached pictures for your reference. Thanks in advance.
Last updated: 2023-12-04

Post by stiller on OPC UA RPI 4.8.0.0 Status Code / "out of range" ^{CODESYS Forge talk (Post)}
Hello, I have an OPC-UA server with an information model. For many values, there is a defined range (e.g., 0 to 100). If a client enters a value outside this range (e.g., 120), the StatusCode should change to Bad. How can I accomplish this? Any help is appreciated! Thank you in advance. Best regards, Christian Stiller
Last updated: 2024-07-10

Post by mmpl on Array to String ^{CODESYS Forge talk (Post)}
I would like to create one large JSON string from an array of objects, where each object contains a value. My current approach involves using a for loop and string concatenation, but with 20,000 elements in the array, this method takes almost 7 seconds and negatively affects the PLC scan time. Is there a more efficient way to accomplish this?
Last updated: 2024-07-18

Post by mmpl on Array to String ^{CODESYS Forge talk (Post)}
I would like to create one large JSON string from an array of objects, where each object contains a value. My current approach involves using a for loop and string concatenation, but with 20,000 elements in the array, this method takes almost 7 seconds and negatively affects the PLC scan time. Is there a more efficient way to accomplish this?
Last updated: 2024-07-18

Post by timvh on RAMP_REAL FB is retaining my output value when i try to re use the FB ^{CODESYS Forge talk (Post)}
I think, that if you set the timebase to T#0s, that it will be reset. But you can also make your own ramp down with a Timer (make sure the PT time is not T#0s):
Last updated: 2024-07-29

Post by durallymax on Help understanding analog in-/outputs ^{CODESYS Forge talk (Post)}
WAGO will use 0-32767 as the raw units. Note a value of 3 means over/under range. Map that IO however you please, then scale in your program using any of the available libraries or with your own simple y=mx+b scaling formula to get to the engineering units you desire. Inverse for the AO to get back to 0-32767.
Last updated: 2024-12-15

Post by timvh on Colors look different when logged in and running ^{CODESYS Forge talk (Post)}
At the top of the Visualisation Properties View, you can enable the "Advanced" options. This will give you access to more properties than what you currently see. There might be a variable linked to the "advanced" colour property where the fill colour is determined by the value of this variable (dword).
Last updated: 2025-01-09

Post by trusty-squire on Help with __SYSTEM.VAR_INFO ^{CODESYS Forge talk (Post)}
Not knowing exactly what you want to accomplish, you can try to use VAR_INPUT MyVar: POINTER TO BOOL; END_VAR MyVar contains the address of your referenced variable, and MyVar^ dereferences it allowing you to access the value. If this doesn't meet your needs, could you add more detail on what you are trying to accomplish?
Last updated: 2025-01-26

Post by smic on put the Port number 80808 in Instance Setting of Deploy Control SL ^{CODESYS Forge talk (Post)}
I am using CODESYS V3.5 SP20 Patch 5. I am trying to use the Webvisu function on a PLC running on Docker. When I enter the port value 8080:8080 in the Instance Setting in Deploy Control SL, it is not saved. Can you please help me?
Last updated: 2025-02-21

Post by kevinm on Programmatically change Tappet on a cam ^{CODESYS Forge talk (Post)}
I am considering using a SoftMotion cam and tappets to activate functions on a machine - for example, triggering a pneumatic valve. I need the ability to change the actuation point (tappet "X" location) from the HMI during machine commissioning. Is there a way to change the "X" value of a tappet programmatically?
Last updated: 2025-04-01

Post by wbj0t on one variable signed to modbus tcp server device and modbus serial device ^{CODESYS Forge talk (Post)}
Hi. Raspberry pi 4 runtime. Runtime version 4.16, IDE version 3.5.21. Is it possible write new value for variable via modbus tcp or serial devices when both enabled? As I see - not. What can I do? It is terrible restriction.
Last updated: 2025-07-17

Post by rkohser on Python Script for Finding "Last saved with" Value ^{CODESYS Forge talk (Post)}
Hi jkilburn, I have the exact same issue and thought I would search a solution on this forum. I see you did not get any answer, did you find a solution on how to extract the last saved version of codesys from the project file ? Roland
Last updated: 2024-01-29

Post by alexgooi on Init Array input on a method ^{CODESYS Forge talk (Post)}
Dear Forum, I would like to initialize an array input on a method. When I do this, I get the following error: "The type of ARRAY [1..2] OF BOOL cannot have a default value in this context." I attached a picture for more clarity. Is this simply not possible or is there a different way of tackling this problem? Thank you in advance
Last updated: 2024-02-26

Post by stuartjr on Disabling forcing of specific variables ^{CODESYS Forge talk (Post)}
I also thought that if I had logic writing a value to this variable, then it would override the force anyway, since I thought that the force request was only applied at the beginning and end of the PLC scan. But this doesn't seem to be the case, the force persists throughout the logic regardless of what I write to the variable with logic
Last updated: 2024-03-15

Post by installwhat on raspistepper error after install ^{CODESYS Forge talk (Post)}
from another post on this forum .... In your library project select Project -> Project Information. On the Properties table remove the "LanguageModelAttribute" Value "Qualified Access Only". This will allow you to access the object without qualifying the access. ...... I guess they've compiled it the library with that setting and now I need to mess around with versions.
Last updated: 2024-04-20

Post by rajesh008 on i can't declear the address in GVL - codesys SP19 Patch5 ^{CODESYS Forge talk (Post)}
The “_AB AT %IW0:word; ” if i called the value then im getting this error. like below "the declartion of the variable with an address assignment cannot be used in a PRG or GVL with the attribute 'subsequent'" This is happening when the GVL is selected in Redundancy Configuration. if i un-select the address declaration is working fine
Last updated: 2024-05-13

Post by talhaali on Active alarm access in ST ^{CODESYS Forge talk (Post)}
Hi, I am trying to access active alarms in code(As alarm count variable updates only when we go to to alarm table frame in visualization). I wrote following code but it is not working: VAR iCountActiveAlarms : INT; parritfActiveAlarms : POINTER TO ARRAY[0..0] OF IAlarm; itfAlarmManagerClientAll : IAlarmManagerClient; END_VAR AlarmManager.g_AlarmHandler.GetActiveAlarms( itfAlarmManagerClient :=itfAlarmManagerClientAll, iCountActiveAlarms => iCountActiveAlarms, parritfActiveAlarms => parritfActiveAlarms); The Value is always 0. Please help.
Last updated: 2024-06-06

Post by talhaali on Can't read Alarm Class from Alarm Storage ^{CODESYS Forge talk (Post)}
Hi, I am trying to access active alarms in code(As alarm count variable updates only when we go to to alarm table frame in visualization). I wrote following code but it is not working: VAR iCountActiveAlarms : INT; parritfActiveAlarms : POINTER TO ARRAY[0..0] OF IAlarm; itfAlarmManagerClientAll : IAlarmManagerClient; END_VAR AlarmManager.g_AlarmHandler.GetActiveAlarms( itfAlarmManagerClient :=itfAlarmManagerClientAll, iCountActiveAlarms => iCountActiveAlarms, parritfActiveAlarms => parritfActiveAlarms); The Value is always 0. Please help.
Last updated: 2024-06-06

Post by talhaali on Can't read Alarm Class from Alarm Storage ^{CODESYS Forge talk (Post)}
Hi, I am trying to access active alarms in code(As alarm count variable updates only when we go to to alarm table frame in visualization). I wrote following code but it is not working: VAR iCountActiveAlarms : INT; parritfActiveAlarms : POINTER TO ARRAY[0..0] OF IAlarm; itfAlarmManagerClientAll : IAlarmManagerClient; END_VAR AlarmManager.g_AlarmHandler.GetActiveAlarms( itfAlarmManagerClient :=itfAlarmManagerClientAll, iCountActiveAlarms => iCountActiveAlarms, parritfActiveAlarms => parritfActiveAlarms); The Value is always 0. Please help.
Last updated: 2024-06-06

Post by talhaali on Can't read Alarm Class from Alarm Storage ^{CODESYS Forge talk (Post)}
Hi, I am trying to access active alarms in code(As alarm count variable updates only when we go to to alarm table frame in visualization). I wrote following code but it is not working: VAR iCountActiveAlarms : INT; parritfActiveAlarms : POINTER TO ARRAY[0..0] OF IAlarm; itfAlarmManagerClientAll : IAlarmManagerClient; END_VAR AlarmManager.g_AlarmHandler.GetActiveAlarms( itfAlarmManagerClient :=itfAlarmManagerClientAll, iCountActiveAlarms => iCountActiveAlarms, parritfActiveAlarms => parritfActiveAlarms); The Value is always 0. Please help.
Last updated: 2024-06-06

Post by talhaali on Active alarm access in ST ^{CODESYS Forge talk (Post)}
Hi, I am trying to access active alarms in code(As alarm count variable updates only when we go to to alarm table frame in visualization). I wrote following code but it is not working: VAR iCountActiveAlarms : INT; parritfActiveAlarms : POINTER TO ARRAY[0..0] OF IAlarm; itfAlarmManagerClientAll : IAlarmManagerClient; END_VAR AlarmManager.g_AlarmHandler.GetActiveAlarms( itfAlarmManagerClient :=itfAlarmManagerClientAll, iCountActiveAlarms => iCountActiveAlarms, parritfActiveAlarms => parritfActiveAlarms); The Value is always 0. Please help.
Last updated: 2024-06-06

Post by talhaali on Alarm Manager: ^{CODESYS Forge talk (Post)}
Hi, I am trying to access active alarms in code(As alarm count variable updates only when we go to to alarm table frame in visualization). I wrote following code but it is not working: VAR iCountActiveAlarms : INT; parritfActiveAlarms : POINTER TO ARRAY[0..0] OF IAlarm; itfAlarmManagerClientAll : IAlarmManagerClient; END_VAR AlarmManager.g_AlarmHandler.GetActiveAlarms( itfAlarmManagerClient :=itfAlarmManagerClientAll, iCountActiveAlarms => iCountActiveAlarms, parritfActiveAlarms => parritfActiveAlarms); The Value is always 0. Please help.
Last updated: 2024-06-06

Post by talhaali on Alarm Table Issues ^{CODESYS Forge talk (Post)}
Hi, I am trying to access active alarms in code(As alarm count variable updates only when we go to to alarm table frame in visualization). I wrote following code but it is not working: VAR iCountActiveAlarms : INT; parritfActiveAlarms : POINTER TO ARRAY[0..0] OF IAlarm; itfAlarmManagerClientAll : IAlarmManagerClient; END_VAR AlarmManager.g_AlarmHandler.GetActiveAlarms( itfAlarmManagerClient :=itfAlarmManagerClientAll, iCountActiveAlarms => iCountActiveAlarms, parritfActiveAlarms => parritfActiveAlarms); The Value is always 0. Please help.
Last updated: 2024-06-06

Post by talhaali on Alarm status in logic ^{CODESYS Forge talk (Post)}
Hi, I am trying to access active alarms in code(As alarm count variable updates only when we go to to alarm table frame in visualization). I wrote following code but it is not working: VAR iCountActiveAlarms : INT; parritfActiveAlarms : POINTER TO ARRAY[0..0] OF IAlarm; itfAlarmManagerClientAll : IAlarmManagerClient; END_VAR AlarmManager.g_AlarmHandler.GetActiveAlarms( itfAlarmManagerClient :=itfAlarmManagerClientAll, iCountActiveAlarms => iCountActiveAlarms, parritfActiveAlarms => parritfActiveAlarms); The Value is always 0. Please help.
Last updated: 2024-06-06

Sort by relevance or date