Post by sigurdrb on Codesys and error messages, warnings exceptions etc. ^{CODESYS Forge talk (Post)}
Hi, I tried some different libraries (CmpApp etc.) to find some global variables that I could read out as a variable in the codesys environment. Do any one of you know which libraries are best suited for this, and how I can read it out? My goal is to send messages, warnings etc. to the system that communicates to the PLC. Currently if something goes wrong I need to see the logfiles, or go online with the controller. I think I could save a lot of time if I could read the errors from our user interface that is connected to the PLC by TCP/IP.
Last updated: 2024-11-06

Post by xabier on BUG CODESYS-NO WORK AUTOMATICALLY RESTARSLAVES ^{CODESYS Forge talk (Post)}
I detect a Bug of Codesys....NO WORK AUTOMATICALLY RESTARSLAVES. I explain the secuence: I have click in my project the option AUTOMATICALLY RESTARSLAVES In the moment start my Ipc, the network ethercat start correctly I disconnect the wire of my first slave and later connect again the wire..(see the screen Bug Codesys restart slave1) NO work the restart automatic slaves...and is not possible execute of FB MC_REset beacuause appear this error (see the screen Bug Codesys restart slave2) The only way for resolver this problem is execute the FB SMC3ReinitDrive I replay the same with PLC BECKHOFF in Twincat3 and I havent this problem...In the moment connect the wire again in the slave the comunication of ehterCat restart and the slave comunication again with out problem
Last updated: 2024-11-07

Post by andrax on CodeSys Raspberry pi I2C driver not found ^{CODESYS Forge talk (Post)}
Ok, here are the libraries I use. First of all, try to get the ADS1115 to run completely on its own. Without MUX or other sensors. As muxboard I use this one: https://www.digikey.de/de/products/detail/sparkfun-electronics/BOB-16784/12714950?utm_adgroup=&utm_source=google&utm_medium=cpc&utm_campaign=PMax:%20Smart%20Shopping_Product_Zombie%20SKUs&utm_term=&productid=12714950&utm_content=&utm_id=go_cmp-18521752285_adg-_ad-__dev-c_ext-_prd-12714950_sig-Cj0KCQiA88a5BhDPARIsAFj595gkPXWPT8aa-EixL97BDWjO988WDhcx-iHOVbqb_H8CLpHBcwLuJW0aAu1JEALw_wcB&gad_source=1&gclid=Cj0KCQiA88a5BhDPARIsAFj595gkPXWPT8aa-EixL97BDWjO988WDhcx-iHOVbqb_H8CLpHBcwLuJW0aAu1JEALw_wcB All other boards don't work for me either. The terminating resistor is missing Important: Before you install the drivers, remove all other device drivers. My drivers are all located in ‘Raspberry I2C MUX_11_2023’
Last updated: 2024-11-11

Post by garrian on How to write multiple coils (Modbus FC15) ^{CODESYS Forge talk (Post)}
Hi there! I'm testing out modbus TCP/IP for my home brewery, using Wago PFC200 as both slave and master. I'm using Wago library WagoAppPlcModbus. Holding registers, input registers' and discrete inputs works fine, but when trying to write multiple coils, it doesn't work. Any idea what I'm doing wrong here? Attached is a screenshot of my code. I tried both using bit mapping and without. If I change to FC05, and write only 1 coil at the time, it works fine. But I want to write all at the same time.. Any help is very appreciated :)
Last updated: 2024-11-16

Post by ben1 on How to write multiple coils (Modbus FC15) ^{CODESYS Forge talk (Post)}
If I am understanding what you are saying, then yes that would be your problem. I would create an array of bools on the client side for the transfer and try that. Or if client can't be changed then use words on server and unpack. But I am not sure if you or I are mis interpreting but it sounds a bit jumbled. I don't know what you have control of, but, if you are turning on BITS in the server, you should write to BITS in the client with a Function 15. If you are writing to WORDS in the server, you should write to WORDS in the client with a Function 16.
Last updated: 2024-11-17

Post by sebastianrapi on Bibliothek: floatingpointutils ^{CODESYS Forge talk (Post)}
@Strucc.c: thanks very mutch. Yes, I think that was the problem. I tried yesterday a similar function, i have found: IEEE32 in REAL FUNCTION IEEE32_TO_REAL : REAL VAR_INPUT IN:DWORD; END_VAR VAR PTREAL:POINTER TO REAL; END_VAR PTREAL:=ADR(IN); IEEE32_TO_REAL:=PTREAL^; END_FUNCTION REAL in IEEE32 FUNCTION REAL_TO_IEEE32 : DWORD VAR_INPUT IN:REAL; END_VAR VAR PTDWORD:POINTER TO DWORD; END_VAR PTDWORD:=ADR(IN); REAL_TO_IEEE32:=PTDWORD^; END_FUNCTION http://www.oscat.de/community/index.php/topic,357.0.html And this works perfect. Now, the only thing that isn't clear is the libary "FloatingPointUtils, 3.5.17.0 (System)"... For me, the libary doesn't work. But the problem is now solved. Thanks a lot.
Last updated: 2024-11-21

Post by dsa28 on OPC UA subscriber not operational ^{CODESYS Forge talk (Post)}
Hi, Thanks for the reply. Please note that the information and links provided are related to OPC UA Client/Server. My problem was related to OPC UA Pub/Sub. In the end I have managed to establish OPC UA Pub/Sub communication between Codesys and TwinCAT systems. Keep in mind that OPC UA Pub/Sub example is not provided in the latest library version 1.1.0.0. The user needs to download the previous version to get the example. During the configuration I ended up with some doubts regarding the usage of IEC_ARRAY type in the dataset definition (see attachment). Can you please give more information on how to use this type? Many thanks.
Last updated: 2024-11-29

Post by hardcoder on EtherCAT Mailbox Gateway ^{CODESYS Forge talk (Post)}
Hi all I found that in the last Ethercat master release (4.8.0.0) the Mailbox Gateway feature has been added. This would be useful for me to connect to a specific slave in my system, since its configuration software supports this type of gateway communication. Anyway I don't find usage information or examples. At the moment I tried to enable it in the ethercat master device settings and I configured with an IP address on the subnet of the ethercat adapter (i.e. ethercat nic configured with static ip 192.168.10.100 subnet 255.255.255.0, mailbox gateway configured to 192.168.10.30). I expected it would have responded to ping commands on the address but nothing happens. I am missing something?
Last updated: 2024-12-11

Post by cihangur on OpC UA server on Raspberry Pi 64 SL runtime ^{CODESYS Forge talk (Post)}
After my tests, I noticed two issues. 1- WinCC disconnects the connection after receiving the GetEndPointResponse message from CoDeSys. (I found it with UAExpert and Wireshark.) 2- It establishes a connection despite waiting for a while on the network with DNS. As a result of this information: I solved the problem by adding the line "193.193.193.150 t9pac" to the C:\Windows\System32\Drivers\etc\hosts file and making Windows accept messages coming from the IP number 193.193.193.150 as coming from t9pac. (t9pac is the name of my PLC running CoDeSys.) If there is a setting that will allow CoDeSys OPC UA to respond to GetEndPointRequest with its IP address, this problem will not occur.
Last updated: 2024-12-12

Post by gseidel on Beckhoff AS1060 and EL7041 configuration ^{CODESYS Forge talk (Post)}
Hi pmanuele, while I don't have firsthand experience with the EL7041 and the step motor AS1060, there are two things you can check: If you use an external encoder, please make sure you use the alternative device description calles "EL7041 1Ch. Stepper motor output stage (50V, 5A) Rev24 with external Encoder". The SoftMotion driver will set the feedback type automatically, and use the correct object for the actual position (16#6010:21 instead of 16#6010:20) If you have problems with changing the controller mode, I assume to velocity, please make sure you change the PDO mapping so that the actual velocity (16#6020:33) and set velocity (16#7010:33) are mapped by PDO. Hope this helps, Georg
Last updated: 2024-12-23

Post by hboertz on CamBuilder and first boundary position not zero ^{CODESYS Forge talk (Post)}
Hi @niallel, it is currently not possible to create periodic cams using SMCB.BoundImplicit(). If you want to create a periodic cam which does not start/end with all slaves values equal to zero, then you must specify the boundary conditions explicitly using SMCB.Bound(). When you finished your cam, you can check via CamBuilder.CheckContinuity(), if the cam fulfills the continuity requirements for a periodic cam (see input isPeriodic). But you are right, it should be possible to create periodic cams using implicit boundary conditions. I have added the following Jira issue, so that this feature might be included in a future SoftMotion version: SM-5537: CamBuilder: It should be possible to create periodic cams using implicit boundaries I hope this answers your question. Best regards, Hendrik
Last updated: 2025-01-08

Post by trusty-squire on Read "Homed" status from EtherCAT drive ^{CODESYS Forge talk (Post)}
@imdatatas, thanks for the info, I increased DSP402.uiHomingMinCycles to 10 and have a good feeling that will solve the issue of "false" homings. It's an intermittent issue so I'll report back once it's confirmed. @bruno-roth, also good info. According to my documentation, bit 14 is used to indicate the homed status. I did a test and the bit always stays true after it's been homed once (eg. even if I initiate a new homing procedure then hit the the e-stop mid homing), so I need to take that into consideration, but I can work with that. Thanks!
Last updated: 2025-01-09

Post by srouse on Adding a Softmotion License to a Weintek HMI ^{CODESYS Forge talk (Post)}
I am trying to add a Softmotion license to my Weintek HMI. The HMI is already licensed for Codesys and I have already purchased a Softmotion license as well. When using the License Manager I get an error saying the licensing info is not available. I am fairly new to working with Codesys so I am at a bit of a loss and there seems very little information online about troubleshooting this specific issue. I have attached the error message below. If there are any ideas of how to troubleshoot this better I would be happy to hear them.
Last updated: 2025-01-09

Post by trusty-squire on Strange problem with the ‘MC_SetPosition’ function ^{CODESYS Forge talk (Post)}
How are the servo drives controlled? EtherCAT, step/dir pulses, other? Another thought is that - if it's step/dir pulse based control - the pulses from the PLC to the drive are getting missed/lost at high frequencies? If that's the case then there would be multiple troubleshooting steps/corrections that could be investigated. You could try to create a simplified program, with all the same parameters, that only has an MC_SetPosition FB you manually trigger and see if you are still getting the same results? When you manually control the motor directly from the servo drive software at the speeds you are calling for, does it move precisely to the target position?
Last updated: 2025-01-18

Post by ton on String nach erlaubten/unerlaubten Zeichen durchsuchen ^{CODESYS Forge talk (Post)}
Hi Timo, FUNCTION Sonderzeichen_Check : bool VAR_INPUT sInputString : STRING; // Zu prüfender String END_VAR VAR i: INT; iAsc: INT; END_VAR Sonderzeichen_Check:= TRUE; FOR i:= 0 TO len(sInputString) - 1 DO iAscii:= sInputString[i]; //Get ASCII value //Check value between 48('0') and 65('9') or between 65('A') and 90('Z') or between 97('a') and 122('z') or IF iAscii >= 48 AND iAscii <= 57 OR iAscii >= 65 AND iAscii <= 90 OR iAscii >= 97 AND iAscii <= 122 THEN //iAscii valit ELSE Sonderzeichen_Check:= FALSE; END_IF END_FOR Diese FUNCTION anrufen: VAR xTest1: BOOL; xTest2: BOOL; sCheck: STRING; END_VAR xTest1:= Sonderzeichen_Check(sInputString:= 'abcuharoahse89347KEWDL'); //=TRUE xTest2:= Sonderzeichen_Check(sInputString:= 'abcuharoahse89347KEWDL?'); //=FALSE IF Sonderzeichen_Check(sInputString:= 'CheckThisSting,') THEN sCheck:= 'OK'; ELSE sCheck:= 'NOT OK'; END_IF
Last updated: 2025-01-20

Post by imdatatas on String length issue in GetRecipeNames method ^{CODESYS Forge talk (Post)}
Hi, If the string length in the GetRecipeNames method is lower than the default value, there will be a problem with the resulting Recipe file names. For example; When the method in the link is called, let's say the defined string length is 19. In this case, the string content is corrupted as in the image. strArr: ARRAY[0..9] OF STRING(19); https://content.helpme-codesys.com/de/libs/Recipe%20Management/Current/pou-RecipeManCommands/GetRecipeNames.html The same problem does not occur when the string definition is made in the default size. strArr: ARRAY[0..9] OF STRING; FYI Regards, Imdat
Last updated: 2025-02-19

Post by imdatatas on String length issue in GetRecipeNames method ^{CODESYS Forge talk (Post)}
Hi, If the string length in the GetRecipeNames method is lower than the default value, there will be a problem with the resulting Recipe file names. For example; When the method in the link is called, let's say the defined string length is 19. In this case, the string content is corrupted as in the image. strArr: ARRAY[0..9] OF STRING(19); https://content.helpme-codesys.com/de/libs/Recipe%20Management/Current/pou-RecipeManCommands/GetRecipeNames.html The same problem does not occur when the string definition is made in the default size. strArr: ARRAY[0..9] OF STRING; FYI Regards, Imdat
Last updated: 2025-02-19

Post by janber0206 on Adding PLC to the List view resolves in Unknown Error ^{CODESYS Forge talk (Post)}
Hello, I try to add one of my PLC from the Gateways to the List view. The Gateway is shown me as online, also i have other remote tools to verify the Internet connection is working. I do the Network Scan and the Gateway shows up, i select it and click on "Add to Server". Then I type in Username and password and click on confirm. There it shows me the "Unkown Error", see screenshot. If I use the wrong credentials it gives me the error message for this. Other Devices work fine it's just this one. Greetings Jannis
Last updated: 2025-02-21

Post by janber0206 on Adding PLC to the List view resolves in Unknown Error ^{CODESYS Forge talk (Post)}
Problem Solved The Problem was within the Usermanagment. There should be 6 files for the Usermanagment in /var/opt/codesys/ .UserMgmtDB.csv .UserMgmRightstDB.csv .GroupDatabase.csv .UserDatabase.csv_ .GroupDatabase.csv_ .UserDatabase.csv The file .UserMgmtDB.csv was missing. I moved the other files in a savefolder. Full Step by step instructions stop the runtime with sudo /etc/init.d/codesyscontrol stop rename the following files on the PI: (or save them and then delete them) in this directory: /var/opt/codesys/ .UserMgmtDB.csv .UserMgmRightstDB.csv .GroupDatabase.csv .UserDatabase.csv_ .GroupDatabase.csv_ .UserDatabase.csv then restart the Runtime: sudo /etc/init.d/codesyscontrol start now reconnect the PLC via the Automation Server - here you will be asked to create a new CODESYS user password, The user management files deleted above are then created again (in /var/opt/codesys/ on the PI).
Last updated: 2025-02-24

Post by tyleretn on Codesys 3.5 SP18 P4 Freezing on Library Update ^{CODESYS Forge talk (Post)}
I have created a library with both code and visualizations to be used in multiple other projects. After I update the library version into the library repository, I have much difficulty updating the version into the main project. I can always update the library version in the Library Manager just fine. My issue, is sometimes Codesys will freeze when opening the visualization that uses the library visualizations. Sometimes it opens, but freezes when I try to access the library visualizations from the Visualization Toolbox. I try letting Codesys run for upwards of 4+ hours and it is stuck in this state. On very rare cases I have no issues and can continue with my work. I haven't found a consistent reason or work around. Has anyone else had this happen?
Last updated: 2025-02-27

Post by matthew on High resolution displays with 150% scaling causes CodeSys IDE to be blurry ^{CODESYS Forge talk (Post)}
I have just upgraded my laptop which has a high res display 2560x1600 and I have to have scaling switch on at 150% but everything looks blurry and not crisp, It seems CodeSys IDE is the only software on my system to look this bad, if I switch to 100% it's crisp but way to small. From a bit of research this could be due to the use of old windows forms or something? I have found a temp workaround that sort of works but not great. You have to run CodeSys in compatibility mode and adjust the DPI settings, this works ok and the editor is clear and crisp again but the actual tool bars are small like running at 100% Anyone got any tips for running CodeSys on high res displays with scaling?
Last updated: 2025-03-03

Post by clarenced on Multiple applications on one device sharing variables. ^{CODESYS Forge talk (Post)}
I got this working using OPC UA. In the logic application I just added a Symbol Configuration. In the HMI application I added a Data Sources Manager and OPC UA Data Source. The one thing I don't like is the way the tags end up being named in the HMI application. In the logic application I have a program named PLC_PRG. It has a variable named testDINT. In the logic application the name I get for this variable is DeviceSet.CODESYS_Control_Win_V3_x64.Resources.Logic.Programs.PLC_PRG.testDINT. This is very long and looks like it could change if I used this on a different device type. Any ideas how I could get this name shortened down to just PLC_PRG.testDINT like it is on the Logic application?
Last updated: 2025-03-06

Post by clarenced on Multiple applications on one device sharing variables. ^{CODESYS Forge talk (Post)}
I got this working using OPC UA. In the logic application I just added a Symbol Configuration. In the HMI application I added a Data Sources Manager and OPC UA Data Source. The one thing I don't like is the way the tags end up being named in the HMI application. In the logic application I have a program named PLC_PRG. It has a variable named testDINT. In the HMI application the name I get for this variable is DeviceSet.CODESYS_Control_Win_V3_x64.Resources.Logic.Programs.PLC_PRG.testDINT. This is very long and looks like it could change if I used this on a different device type. Any ideas how I could get this name shortened down to just PLC_PRG.testDINT like it is on the Logic application?
Last updated: 2025-03-06

Post by felipemsgarcia on Axis EtherCAT address ^{CODESYS Forge talk (Post)}
Hello, Thank you for your answer. I'm afraid I was not clear on what I was trying to achieve. I'm trying to change parameters and command axes from inside a function block and the first thing that came to my mind was pass both the EtherCAT slave and axis to the function block (as image attached). But, I believe it's worse than just pass directly the EtherCAT slave address to the function block (is it???). However I was wondering if there was a way to get the EtherCAT address directly from the axis, so I don't need to pass the EtherCAT slave nor the EtherCAT address to the function block. Thank you again!
Last updated: 2025-03-07

Post by mehakfatima on Need Help Configuring Energy Analyzers via Modbus TCP & RTU (RS-485) in CODESYS 3.5 ^{CODESYS Forge talk (Post)}
Hello everyone, I am currently working on reading data from energy analyzers using Modbus TCP and RTU (RS-485). In my previous software, I used the following method to add slave devices (i have attached the image) and configure registers: Add the Modbus slave device. Configure the communication parameters (baud rate, parity, etc.). Define the registers and their addresses for data retrieval. Now, I am trying to achieve the same in CODESYS 3.5, but I am not sure how to configure the Modbus master, add slave devices, and set up the registers properly. If anyone has experience with Modbus TCP/RTU setup in CODESYS 3.5, I would really appreciate your guidance! A step-by-step explanation or any references/tutorials would be extremely helpful.
Last updated: 2025-03-13

Sort by relevance or date