Post by elsmart on Sequential read and triggering of Modbs RTU channels in application ^{CODESYS Forge talk (Post)}
Hello I need some help understanding how to use Modbus RTU (COM port) in Codesys enviroment. I defined a Modbus Server device (slave) in device tree and added some channels to read from (function 3). Also I set trigering mode to Application. I have a POU in which I want to trigger each channel one after the other something like this (C code for better visualisation): for (int i = 0; i < channelsCount; i++) { triggerChannel(channelsArray[i]); // Start transmission while(channel.xBusy); // Wait for transmission to complete } I have found ModbusChannel function block documentation but examples are scarce. I don't understand how rising edge triggering works. What would be the best solution for achieving sequntial channel triggering? What is the common way to read multiple Modbus channels once every time a specified POU is executed?
Last updated: 2025-05-16

Post by abuckie on Getting raw value as full resolution for ADS1115 ^{CODESYS Forge talk (Post)}
I just found this and I am getting a value larger than 16 bit, around 81000 something. I am reading a 5 volt value and I am using level shifters for the i2c bus. This is how I have the channel configured: ADS1115.usiAddress := 16#48; ADS1115.ChannelConfigs[0].Active := TRUE; ADS1115.ChannelConfigs[0].PGA := FSR_6144mV; ADS1115.ChannelConfigs[0].InputMux := Single_0; RawAnalogValue := ADS1115.Channels[0].Value; It looks like every value is a multiple of 3. Any idea where to look to fix this? I think i found what I want to change in UpdateChannels Channels[FChannelNo].Value := INT_TO_REAL(WORD_TO_INT(LValue) * GetFullScaleRange(ChannelConfigs[FChannelNo].PGA)) / 2048.0; I try to edit it but I can't, sorry if this is a basic question, I am new to CODESYS.
Last updated: 2025-05-22

Post by buczekj on About CPU Loading ^{CODESYS Forge talk (Post)}
This is a phenomenon that I have seen myself and with others. Texas instruments wrote an application note with this same issue. They noted with Codesys 3.5.19.10, that selecting CPU 1 as the EtherCAT task showed CPU spiking improvements over the performance of cores 0, 2, and 3. It appears to be linked to EtherCAT, are you configuring for use with distributed clocks? If so, I recommend choosing the 'Based on Input Reference' option. I have found it to reduce the CPU usage spike maximum slightly (see attached). See link to TI (also attached in case link breaks) https://www.ti.com/lit/an/spradh0/spradh0.pdf?ts=1723546111357
Last updated: 2025-07-01

Post by rer-code on Codesys 3.5.18.60 – Application Loss and Persistent Data Corruption ^{CODESYS Forge talk (Post)}
Hi, I’m currently managing over 50 PLCs running Codesys version 3.5.18.60. At seemingly random intervals, some of these devices experience a failure where: All persistent variables are lost. Attempting to log in results in the message: “The application does not exist on device. Do you want to create it and proceed with download?” The log shows: “Loading retain-data/bootproject failed.” From what I’ve gathered, this may be due to a corrupted persistent data file, but I’m not entirely sure how to confirm or resolve this issue. If anyone has encountered something similar or has suggestions for troubleshooting or preventing this, I would greatly appreciate your input. Best regards
Last updated: 2025-08-19

Post by sumit on Remote Ethernet/ip Adapter communication with scanner running on codesys ^{CODESYS Forge talk (Post)}
Hello there, I have my ethernet/ip adapter (from Texas Instrument) running on Texas Instrument Board and I have configured the scanner on codesys. I have mapped the I/Os and I can see (on wireshark) the frames coming from adapter but I don't see my input variables in scanner get updated, they just stay at 0. I wanted to see the real data that has been sent from adapter to scanner on codesys. I am not sure if the problem is in I/O mapping or there is a step/s that I have missed. I have attached the screenshot of my project for your ref. Thank you, Sumit
Last updated: 2023-12-15

Post by sumit on Remote Ethernet/ip Adapter communication with scanner running on codesys ^{CODESYS Forge talk (Post)}
Hello there, I have my ethernet/ip adapter (from Texas Instrument) running on Texas Instrument Board and I have configured the scanner on codesys. I have mapped the I/Os and I can see (on wireshark) the frames coming from adapter but I don't see my input variables in scanner get updated, they just stay at 0. I wanted to see the real data that has been sent from adapter to scanner on codesys. I am not sure if the problem is in I/O mapping or there is a step/s that I have missed. I have attached the screenshot of my project for your ref. Thank you, Sumit
Last updated: 2023-12-15

Post by royw on Profinet library for C# ^{CODESYS Forge talk (Post)}
Hi, I don't know if I'm in the right place or if it's even possible... I'm looking for a way to address a Profinet device with Record Read and Write from my own PC. I actually only need very few commands to configure our device. This means setting the MAC address and a serial number. We would like to do this from a C# program. Now we are looking for a library or something similar. Since you can do it from Codesys, I thought there might be a DLL or something similar that you could use for this. As I said, we don't want real-time queries of the cyclic data but only record read/write. Does anyone have any helpful hint? Thanks in advance
Last updated: 2023-12-22

Post by fdmartello on Unable to compare projects containing alarm manager 4.5.0.0 ^{CODESYS Forge talk (Post)}
Hello. In Codesys version 3.5.19.50 when comparing two projects that have an "Alarm Configuration" obj from the Alarm Manager library vers. 4.5.0.0 the attached error pops up. This originally happened with two projects that I converted from vers. 3.5.17.30 so, thinking it was some conversion issue, I created two clean projects directly in 3.5.19.50 using the Standard Project template and only added the Alarm Configuration objects in them. The result is the same and the only way I found that allowed me to compare them is by deleting the incriminated object in one of the two projects. Has anyone else encountered this issue? Best regards
Last updated: 2024-01-19

Post by alexgooi on Is it possible in the log to see previous shutdown ^{CODESYS Forge talk (Post)}
Hi DavidBo, In general Codesys is used to control equipment and an exception is the worst thing that can happen in your installation. If you cannot prevent the exception from triggering, you could implement a Try catch statement, with this solution your controller keeps on running and you are able to handle the exception. __TRY //This statement will trigger an exception Result := 4/0; __CATCH(exc) //Handle the exception HandleException(exc, strExceptionText => strExceptionText); // From the Codesys help file //Create a log file //-------------------------------------------------------- __ENDTRY What you also could do is implement implicit checks, these functions cover most of the exceptions (like dividing by zero) See picture But in general avoid a complete controller shutdown!
Last updated: 2024-02-09

Post by nilesh on Request for Assistance with Online Logic Changes in PLC System using Codesys ^{CODESYS Forge talk (Post)}
Dear Sir, We are writing to seek guidance regarding our current situation with the Opto 22 Groov EPIC PR1 PLC system. Over the past year, we have successfully downloaded and implemented logic using Codesys, and the PLC has been operational without issues. However, we now require minor modifications to the logic. Despite attempting to upload the modified logic, we are unable to see the "online change" option, prompting us to consider a direct logic download. Our concern is that during this process, certain digital outputs or analog outputs might momentarily disrupt operations, which is unacceptable given the system's continuous 24x7 operation. We have explored online changes in other PLC systems, but due to the absence of the last downloaded backup, we are unable to proceed confidently.
Last updated: 2024-03-01

Post by ph0010421 on Stepper Drive with Ethercat ^{CODESYS Forge talk (Post)}
Hello That's certainly CiA402. I'll attach a part of the manual for my servos, but the state diagram should be the same at yours. To be sure, get one from your manufacturer. Look at the bits in the StatusWord to see where you are in the diagram, then twiddle the bits in the ControlWord to get you to the next step. Then there are other bits in the StatusWord to tell you 'InPosition' and things like that. From the screenshot, as it mentions only 'PositionProfile' the driver will create the motion profile. So you need to put a target position in here - there should be profile velocity somewhere? Possibly, you need to write these with SDO's? At the minimum, you need to write a value to 0x6081, 0x6083 and 0x6084 (velocity, accel, decel)
Last updated: 2024-03-22

Post by esave on Softmotion Light Problem: The license is missing or invalid ^{CODESYS Forge talk (Post)}
Hello everybody I want to controll a stepper driver from Leadshine (EM3E-556E). The EtherCat slave is CiA 402 compatible. Because of this I bought the Softmotion Light Package from Codesys and implemented it in my project. I rightclicked the EtherCat slave and added the Softmotion Light axis. But now the error message shows: "The license is missing or invalid. The PLC runs in demo mode." What have i done wrong? I use Codesys 3.5.17. Is it possible that the stepper driver is not compatible with the Softmotion license? Thanks for all your help
Last updated: 2024-05-02

Post by robpqs on Program from one PLC to other WAGO 750-8204 ^{CODESYS Forge talk (Post)}
Hello, You use the WAGOUpload tool. You can download it on the download center of WAGO. Make a backup and restore it on the new device. (if can check the remanent data to copy the persistent variables if necessary) You can also use a SD card, go to the WBM copy it the image to the SD card and restart the other controller on the SD card. In the WBM, copy it back to the internal flash. If you contact your local Wago office, they will more than probably help you. There is also a WAGO forum. RP,
Last updated: 2024-05-27

Post by damian177 on CM4S GPIO's in Codesys ^{CODESYS Forge talk (Post)}
Hi, I am running my application on device based on Compute Module 4S (Cortex-A72 (ARMv8) 64-bit ). On this device I installed RPi Runtime in 4.11.0.0 version. In my project I use device: Codesys Control for Raspberry Pi 64SL and my project works, but I actually do not have acces to all GPIO's , because GPIOs Compute Module is available only in 3.5.16.0 version and it doesn't work. Properly work GPIOs B+/Pi2 but using this device I do not have acces to all GPIO's in CM4S. Anyone of can tell me how add GPIOs Compute Module 4.11.0.0 to my project ?
Last updated: 2024-05-28

Post by timothyzalusky on Strange Behavior on Raspberry Pi ^{CODESYS Forge talk (Post)}
Hello, I am seeing some weird runtime behavior related to the EQ function on a rapsberry pi based system. I have attached a screenshot showing the strange latching I am seeing on the EQ function, and I have not seen this behavior before. I tried freshly restarting the runtime and it has this same behavior. Anyone seen this? I am on 3.5.20 with the latest runtime installed. Basically, as soon as it hits one of those EQ's in the program, it latches effectively locking the output on. Any input from the Codesys team would be appreciated as well as anyone that might know what I am seeing.
Last updated: 2024-06-18

Post by etalp on Eaton XC303 firmware update via USB ^{CODESYS Forge talk (Post)}
Hi, I'm struggling with updating my xc303 to firmware 3.5.17. It is possible only via USB port. I've installed proper update files on the USB then plug it into the PLC's USB port and restarted the device. Shortly after LED's on the PLC started to blink, so updating process has started. But after 10 minutes the PLC LED turned off and after all I could't serach for this PLC in Codesys, but could ping it. Could someone eplain to me proper procedure of updating the fimrware in XC303 via USB? Is it neccesary to STOP the PLC switch after pluging the USB?
Last updated: 2025-10-15

Post by damian177 on RPi, Codesys , RS232 ^{CODESYS Forge talk (Post)}
Hi, so far I have only used one com port - built-in interface in RPi - RS232 (dev/serial0) as COM1 in Codesys, and my CODESYControl_User.cfg have congiuration like below: [SysCom] Linux.Devicefile=/dev/serial portnum := COM.SysCom.SYS_COMPORT1 Actually I added to my Rpi Hat with 2xRS232 (SPI). - /dev/spidev0.0 and /dev/spidev0.1 How I should change my CODESYControl_User.cfg file to use added porta as COM2 and COM3 in Codesys ?
Last updated: 2023-10-05

Post by anhkdv on Data storage and Export in Codesys ^{CODESYS Forge talk (Post)}
I am doing a SCADA project on temperature and humidity monitoring system. The customer requested that we store the database through codesys without the need for intermediary software such as MySQL, MSSQL,... and be able to export reports at selected times, reports exported to csv files. , xslm,... Can anyone help me?
Last updated: 2023-10-29

Post by davidbo on How to switch between dynamic IP address and dynamic? ^{CODESYS Forge talk (Post)}
I want to make an application with a UI for CODESYS Control for Raspberry Pi MC SL which make it possible to switch between dynamin and fixed IP address and to set the IP address. However I do not know whether that is possible?
Last updated: 2023-11-06

Post by rmaas on Responsive Design Example ^{CODESYS Forge talk (Post)}
Hi, I just tried the example project with control WIN x64 and for me this is working correct. The only difference is that it is showing 'TabletPortrait' when i hold my smartphone in portrait mode and 'Monitor' when i hold my smartphone in landscape mode. This is because smartphone resolutions have increased i guess... You could check what resoution is detected and change accordingly in IsSmartphone method.
Last updated: 2024-07-04

Post by mucleus on What is the solution for "Application stopped on recovery switch request"? ^{CODESYS Forge talk (Post)}
Hi, everyone. I am using CODESYS RTE and Profinet I/O or EtherCAT I/O. Occasionally (once every 1-2 months) the attached image occurs and the program stops. I want to know why this phenomenon occurs and how to solve it. I attached log. Please help me. Thanks.
Last updated: 2024-07-05

Post by elerensx on Uninstall Codesys2.3 got RUNDLL There was a Problem Starting error ^{CODESYS Forge talk (Post)}
Try to repair Codesys2.3 and need to uninstall and reinstall it. Got this RUNDLL message when uninstall Codesys 2.3: There was a problem starting, the specificed module could not be found. Please refer to attached file. Followed suggestions from Microsoft website and didn't work out. I am using Codesys2.3.9.16. Any help is appreciated.
Last updated: 2024-07-15

Post by flappyman on licenses question ^{CODESYS Forge talk (Post)}
I hope this tread will be able to help me. I got your new licenses and it was working perfectly fine. Unfortunately, my PLC got severely damaged and it can not run anymore. Is it possible to somehow release the license so I could use it again. I have all information for the device and can provide it.
Last updated: 2024-08-05

Post by gepert on parker servo and position ^{CODESYS Forge talk (Post)}
Gentleman OMG, I made a huge mistake when i tried and moved shaft by hand i hold cover(as on photo) in my fingers. I was convinced that shaft has key but it there is not key. So when i turn cover it slide on shaft. When i take off cover and drive is in standstill, shaft does not move. So everything works perfectly
Last updated: 2024-08-07

Post by david3278 on Advice on OOP hardware I/O code structure ^{CODESYS Forge talk (Post)}
For anyone struggling with electrical engineering assignment help, I highly recommend seeking professional assignment help. These services offer expert guidance on complex topics like circuit analysis, power systems, and electronics. They can save you time, improve your understanding, and help you meet tight deadlines. Great option for ensuring high-quality work and better grades.
Last updated: 2024-09-30

Sort by relevance or date