Post by dosnova on *exception* [processorloadwatchdog] occurred in: app=[all], task=[all] ^{CODESYS Forge talk (Post)}
I've the same problem. I'm not able to solve..
Last updated: 2026-02-10

Post by as1984 on Codesys Control log "eventbuffer full" ^{CODESYS Forge talk (Post)}
Have you found a solution for this? Id be thankful for every hint. I have a controller with the same events in log and sometimes it crashes. Memory of the codesys3 task rises until the linux system kills the task because the controller runs out of memory.
Last updated: 2024-01-17

Post by tk096 on High Cycle Times for SoftMotion_PlanningTask when using AxisGroup ^{CODESYS Forge talk (Post)}
Hi, under this circumstances the performance of a Raspberry Pi 4 should be sufficient to run a Softmotion robotics application. A closer look at the project would be required. Maybe you could contact the codesys support? Usually it is recommended to run the planning task cyclically every 2ms with task priority of 0 on a dedicated core. In the task configuration you can have a look at the average and maximum execution time of the planning task. You could use the function block SMC_TuneCPKernel (https://content.helpme-codesys.com/en/libs/SM3_Robotics/Current/SM3_Robotics/POUs/AdministrativeConfiguration/Computation/SMC_TuneCPKernel.html) to define suitable values for the parameters 'fSyncBufferDuration' and 'fPlanningInterval'. However, as previously mentioned, the performance of a Raspberry Pi 4 with realtime patch should be sufficient. The 'fPlanningInterval' parameter specifies the maximum planning step width in seconds. The cycle time of the planning task should not permanently exceed this value. A higher value reduces the computational effort, but can lead to a violation or no full utilization of the set limit values for velocity, acceleration and jerk. From a starting value of 0.016 seconds, the value should be increased gradually until the performance is acceptable. The parameter 'fSyncBufferDuration' specifies the size (in seconds) of the buffer between the planning and fieldbus task. The cycle time of the planning task must not exceed this value at peak times (this will lead to the error SMC_CP_QUEUE_UNDERRUN). A higher value can compensate for peaks in the cycle time of the planning task. At the same time, however, this also increases the latency for executing interrupts and aborting movements.
Last updated: 2024-03-22

Post by s1mon on Two OneWireMaster on one Raspberry PI 5 ^{CODESYS Forge talk (Post)}
Took me a while to work on this again. I testes today with a fresh setup and it works now. My OneWireCycle tasks runs for around 10seconds. I guess my mistake was that I put the cycle task for the OneWire Task to a too small number. Thx for the support!
Last updated: 2025-11-22

Post by gatto on EXCEPTION [watchdog] how to find position cause ^{CODESYS Forge talk (Post)}
hi. My plc is weidmuller UC20-WL200-AC, IDE CODESYS 3.5.20.40, see picture for task settings. sometime i've got the plc stop. Reading the log, I find: EXCEPTIONPOSITION : IP=0x(nil) (no IECcontext could be retrieved) component CmpIecTask EXCEPTION [Watchdog] occurred: App=[Application], Task=[TASK_O_MAIN] component CmpIecTask How to find the position of problem?
Last updated: 2026-02-06

Post by fedex03 on Read Global Variable from an IoT Device ^{CODESYS Forge talk (Post)}
Hello everyone, I am new to the forum, and to programming with CodeSys. I am dealing with IoT device for industry and I should check if a device is able to read/write global variables in an EtherNet/IP Master. Since I do not have an EtherNet/IP PLC, I thought of using CodeSys as a softPLC. I created a program with a set of global variables (GVL) and a task that increments them. I would like to know if I need to enable any options so that the global variables can be read by IoT devices. My device supports Class 2 Class (Explicit Messaging Connection) communication. Thank you in advance for your help.
Last updated: 2025-07-22

Post by vformanek on irq-set piority is not working in plc-shell ^{CODESYS Forge talk (Post)}
Hello, I am currently having issues on CODESYS Control for linux SL with DTH expiring. I have followed several tutorials of creating a proper RT linux. Then I further configured the linux based on this tutorial: https://content.helpme-codesys.com/en/CODESYS%20Control/_rtsl_performance_optimization.html Currently I am getting DHT expires in the communication and I am trying to increase of the priority of the network task which manages the PROFINET network adapter. I am following this tutorial: https://content.helpme-codesys.com/en/CODESYS%20PROFINET/_pnio_trouble_connection_failure.html But the irq-set is not changing the priority. See the image bellow....
Last updated: 2024-01-05

Post by mystx on Timeout Error in Modbus Communication with WAGO PFC200 and iEM2050 Meter using 750-652 Module ^{CODESYS Forge talk (Post)}
Hello I have the same problem, anyone have some idea?? Regards
Last updated: 2024-07-30

Post by mystx on Timeout Error in Modbus Communication with WAGO PFC200 and iEM2050 Meter using 750-652 Module ^{CODESYS Forge talk (Post)}
Hello I have the same problem, anyone have some idea?? Regards
Last updated: 2024-07-30

Post by mystx on Timeout Error in Modbus Communication with WAGO PFC200 and iEM2050 Meter using 750-652 Module ^{CODESYS Forge talk (Post)}
Hello I have the same problem, anyone have some idea?? Regards
Last updated: 2024-07-30

Post by andreiot40 on Step motor ECT60 Ethercat in codesys 3.5 ^{CODESYS Forge talk (Post)}
Thank you so much ! It works, I have communication.
Last updated: 2024-08-17

Post by gatto on Undertanding Application Based Licenses ^{CODESYS Forge talk (Post)}
Hi, i think you are right. Did you press the key shopping cart? Codesys tells you the license. What I don't appreciate is that i need an additional license for communication. The system reports opc ua but this cheats you. This is communication that also concerns the tag symbols that codesys eth v3 exchanges with an operator panel. Attached is a screenshot of my case where you can see that communication opc ua is cheating you. 512 tags included in the program license are few. So, I had to buy 2 licenses. one for the program and one for communication. I don't like this policy.
Last updated: 2024-11-11

Post by taqamert on CAN communication settings for USB2CAN-C ^{CODESYS Forge talk (Post)}
Did you solve the problem? I need to help same topic
Last updated: 2024-11-12

Post by rajshaswat on OPC-UA and other communication questions ^{CODESYS Forge talk (Post)}
check this if it helps : https://youtu.be/Hdpbsp2jG3Q?si=NTwK13c_YOSZXM3v
Last updated: 2024-04-06

Post by dawidr on Timeout Error in Modbus Communication with WAGO PFC200 and iEM2050 Meter using 750-652 Module ^{CODESYS Forge talk (Post)}
Last updated: 2024-04-07

Post by mos89p on Data source and safety PLC ^{CODESYS Forge talk (Post)}
it works only for me when i specify an IP adress in communication tab
Last updated: 2024-06-17

Post by eschwellinger on stablish CAN communication through the PC's USB port ^{CODESYS Forge talk (Post)}
since 3.5.20.10 version here: c:\Windows\System32\config\systemprofile\AppData\Roaming\CODESYS\CODESYSControlWinV3x64\<unique number="">\</unique>
Last updated: 2025-12-14

Post by dat422 on CODESYS crashes when adding standard OPC UA Information Model to Communication Manager ^{CODESYS Forge talk (Post)}
An Update to SP22 solved the issue.
Last updated: 2026-03-27

Post by eschwellinger on Unable to deploy "Control for Linux SL 4.18.0.0" ^{CODESYS Forge talk (Post)}
we need the Systeminformation in the Communication tap(logged in)
Last updated: 2026-02-17

Post by nano on Modbus TCP/IP slave communication errow ^{CODESYS Forge talk (Post)}
please tell us the exact error message from diagnostic. U can view it at devicetree in the node-element diagnostic from modbus-configuration. u also can activate the function auto-reconnect in master and increase a little bit the timeout and the repetition to male thw communication a little bit more robust
Last updated: 2024-02-04

Post by rd76065 on Opto 22 Groov PR2 Modbus TCP Master communication ^{CODESYS Forge talk (Post)}
Previously, I have used ModbusEthernet_04 library for Wago for ModbusTCP Master communicational in Codesys V2.3. How to use same communication of similar UDT for Opto22 Groov PR2 PLC in Codesys V3.5 SP20. Can I use OSCAT library - Network -MB_Client or IODrvModbusTCP - ModbusRequest for this requirement? If any other please guide.
Last updated: 2024-05-31

Post by timl on BacNet "Unaufgelöste Referenz" ^{CODESYS Forge talk (Post)}
Hallo, ich habe Probleme beim nachbauen des BacNet2 Tutorials "Erste Schritte" aus der CODESYS Online Help. https://content.helpme-codesys.com/de/CODESYS%20BACnet/_bacnet_first_steps.html Das Anlegen des BacNet2 Servers und der danach folgenden BacNet Datenpunkte erfolgt ohne Probleme. Der Code lässt sich mit F11 auch Fehlerfrei generieren. Beim Download auf die SPS tritt dann der Fehler auf dem Bild auf. Anbei auch ein Bild des Logs nach dem Download. CODESYS BACnet 2.0.0.0 ist über den Installer runtergeladen. Device: CODESYS Control Win V3 x64 Version 3.5.19.40 CODESYS 3.5.19.40 Im Bibliotheksverwalter ist BACnet2 2.0.0.0 aufgeführt Die Konfigurationsdatei habe ich mit folgenden anpassungen abgespeichert: [ComponentManager] Component.1=CmpTargetVisuStub Component.2=CmpWebServer Component.3=CmpWebServerHandlerV3 Component.4=SysCpuMultiCore Component.5=SysReadWriteLock Component.6=SysCpuBreakpoints Component.7=SysPipeWindows ;Component.8=CmpHilscherCIFX ;Component.9=CmpPCANBasicDrv ;Component.10=CmpCANFoxDrv ;Component.11=CmpIxxatCANDrv ;Component.12=CmpBlkDrvCanServer ;Component.13=CmpBACnet Component.14=CmpBACnet2 [CmpBACnet2] ;configuration file of the BACnet stack IniFile=$PlcLogic$/bacstac2.ini ;task priority of the BACstack process task, default: TASKPRIO_NORMAL_END (159) TaskPrio=128 ;name of the named pipe for the communication with the BACstack AppName=/tmp/BACnetServer Habe ich etwas vergessen?
Last updated: 2024-02-16

Post by rmaas on Fieldbus has lost synchronicity ^{CODESYS Forge talk (Post)}
Hi, On a gantry system with 2 axis i am getting the following error: SMC_DI_FIELDBUS_LOST_SYNCRONICITY This happens random, sometimes it happens every 5 minutes and sometimes no error for 2 hours... The Setup: - Using codesys 3.5 SP20 with all latest libs... - Kontron AL Pi-Tron CM4 with Preempt realtime patch (Raspberry Pi 4) - Codesys runtime 4.11.0.0 (single core) - CODESYS Control for Raspberry Pi SL licensed - Softmotion + CNC + Robotics licensed - 2x Leadshine EL8-EC400 servo drives - Axis group for a 2-axis T-Gantry Ethercat network wiring: Ethercat master softmotion -> Beckhoff EK1100 -> Servo drive #1 -> Servo drive #2 Ethercat Cycle time = 4ms Max Jitter = 140~150 What i have tried so far: - changed the sync offset from 20% to 30% - changed ethercat task priority from 1 to 0 Running tasks: - Ethercat tast: Prio = 0, Interval = 4ms - Main task: Prio = 1, Interval = 8ms - Visu task: Prio = 31, Interval = 100ms - Softmotion planning task: Prio = 15, Freewheeling - 3 other default tasks that were created by AC_Persist Motion fb's are called in the ethercat task... Does anyone have an idea how to fix this? Any help is greatly appreciated!
Last updated: 2024-04-11

Post by cfam on Codesys Control for PLCnext SL, Bus not running ^{CODESYS Forge talk (Post)}
Good day I would appreciate it if you can give me some advice on how to fix my "Bus Not Running Error". I am Using Codesys 3.5 SP20 and Codesys Control PLCnext SL V4.12.0.0. Codesys control was installed on the device and I can log into it but it seems that it does not pick up the PLC or the IO attached (Please see attached Image). The Bus Cycle Task of the AXL F 2152 is set to Main Task and the "Always update Variable" is Enabled on each IO Module. My Main Task interval is set to 100ms and Priority is set to 0. I have tried other options and none seem to work. Your response to this issue will be highly appreciated.
Last updated: 2024-08-12

Post by cfam on Codesys Control for PLCnext SL, Bus not running ^{CODESYS Forge talk (Post)}
Good day I would appreciate it if you can give me some advice on how to fix my "Bus Not Running Error". I am Using Codesys 3.5 SP20 and Codesys Control PLCnext SL V4.12.0.0. Codesys control was installed on the device and I can log into it but it seems that it does not pick up the PLC or the IO attached (Please see attached Image). The Bus Cycle Task of the AXL F 2152 is set to Main Task and the "Always update Variable" is Enabled on each IO Module. My Main Task interval is set to 100ms and Priority is set to 0. I have tried other options and none seem to work. Your response to this issue will be highly appreciated.
Last updated: 2024-08-12

Sort by relevance or date