Post by imdatatas on MC_CamIn did not work properly with SMC_FreeEncoder on SoftMotion 4.17.0.0 ^{CODESYS Forge talk (Post)}
Hello, I am facing a problem with the new Softmotion 4.17.0.0 version. Has anyone encountered a similar problem, what is the solution? I would be happy if you could share it. Problem description: -- "SMC_FreeEncoder" encoder axis is the master, -- The motor of the servo driver on the EtherCAT bus is the slave axis. -- When the MC_CamIn block executed, the InSync output is activated. However, although the master encoder axis position value changes, there is no movement in the slave servo axis! Test steps: 1-) EtherCAT servo axis installed, configured and motion test was performed with MC_Jog. No problem. 2-) Softmotion general axis pool > SMC_FreeEncoder was added and pulse amount configuration was performed. No problem. 3-) Incremental encoder actual count value was transferred to the "SMC_FreeEncoder.diEncoderPosition" variable as DINT under the ethercat task in every cycle and the encoder axis position value was observed. No problem. 4-) A simple CAM table with a 1:1 ratio was created under the project tree. (For example: Simply, when the encoder rotates 1 turn, the motor will rotate 1 turn.) 5-) The SMC_FreeEncoder axis enabled with MC_Power and brought to the StandStill state. 6-) The MC_CamTableSelect block was run with default input values ​​(all absolute) and only the Cam table name was specified. The Done output was seen successfully. No problem. 7-) The MC_CamIn block was activated with default input values ​​(absolute) and only the master encoder axis name, slave servo axis name, CamTableID input pins was specified and then "Execute" input set to TRUE. 8-) The InSync output information of the MC_CamIn block observed as TRUE. However, although the encoder axis value changed, the position value of the slave axis did not change at all, it did not move. It always remained at 0.0mm. 9-) When I repeated the same steps above, only changing the master axis to SM_Drive_Virtual instead of FreeEncoder and gave movement to the virtual axis, this time the slave axis moved successfully. However, when the same steps and operations are performed with the same IDE just downgrade SoftMotion version from 4.17.0.0 to 4.10.0.0, everything works normally and without problems as expected in MC_CamIn block with FreeEncoder master. (By the way, The used IDE version is Codesys V3.5 SP20patch3.) Best Regards Imdat
Last updated: 2024-11-11

Post by tk096 on SMC_Interpolator + SMC_controAxislbyPos ^{CODESYS Forge talk (Post)}
Hi, you can define a start position for your GCode. How the start position can be defined depends on the CompileMode: For File and SMC_CNC_REF: Set the start position input of SMC_NCInterpreter (https://content.helpme-codesys.com/en/libs/SM3_CNC/Current/SM_CNC_POUs/NC2/Interpreter/SMC_NCInterpreter.html) For SMC_OutQueue: * Right-click on the CNC object in the project tree * Select Properties * Select the tab 'CNC' * Set the start position Concerning your second question: If the new set position cannot be reached with the given velocity limit (AXIS_REF_SM3.fSWMaxVelocity), SMC_controlAxisByPos will report bStopIpo and close the 'gap' with the given gap dynamics (SMC_controlAxisByPos.fGap*).
Last updated: 2024-02-07

Post by brell on Automatic xExecute NBS.TCP_write ^{CODESYS Forge talk (Post)}
I've recently started experimenting with CODESYS for a project and am fairly new to it. I'm currently working with Function Block Diagrams (FBD) to set up TCP communication between a server and a client, where the client is implemented as a Python script. Once the communication is established, my connection status changes to True, which is the expected behavior. My challenge arises with the TCP write module, which requires the xEnable_write flag to toggle between True and False. If xEnable_write remains True, the module only performs a single write operation. To address this, I introduced a falling edge trigger (F_TRIG), expecting it to help in toggling xEnable_write and it does, However, I've encountered an issue where in the beginning after connxion established I need to manually set xEnable_write to True for the system to work as intended. I'm looking for a way to automate this process so that xEnable_write becomes True automatically upon establishing a connection . Initially, I tried setting xEnable_write to True from the start, but this approach didn't work well since it left the flag permanently True, preventing further toggling. I also experimented with using a TON timer, but I faced similar issues. I am seeking a solution that automatically toggles xEnable_write between True and False after a connection is established, ensuring continuous write operations without manual intervention. Any advice or guidance on how to achieve this would be greatly appreciated."
Last updated: 2024-03-05

Post by jari-koivuluoma on Problem trying Net Base Services 3.5.15.0 TCP connection ^{CODESYS Forge talk (Post)}
Solved. Just in case that someone else is now to this also. It seems that the xDone of the TCP_Connection FB goes true once client disconnects and then you need to reset the FB by setting the xEnable to false.
Last updated: 2024-10-04

Post by eschwellinger on Persistence Manager: Config File not found? ^{CODESYS Forge talk (Post)}
..strange just switching of this device without graceful Linux OS shutdown? Reset orgin on the device tree and a new download of the application will bring it up and running again but sure then the persistent data are for sure lost.
Last updated: 2024-11-02

Post by ph0010421 on Dynamically enabling/disabling Modbus slave devices in runtime (performance issue with timeouts) ^{CODESYS Forge talk (Post)}
Hello If you uncheck 'Auto restart Communication', it will try once and never again. You can manually reset the slave if needed : Slave.xReset (or something similar) Or I have a ModbusRTU library if you want to try it.
Last updated: 2025-08-12

Post by reinier-geers on Power off ^{CODESYS Forge talk (Post)}
For power off i need to give a MC_Reset ???? Why ??? To power up i need MC_Power , but when i reset the inputs it doesnt power off the drive ! Why ? If i would use the controlword on ethercat it would. Why nog in MC ?
Last updated: 2024-01-12

Post by victor on Trend-Trace / Time x-axis ^{CODESYS Forge talk (Post)}
Good morning, I am new to codesys, I am currently manipulating the Trace and Trend elements and I would like to know if it was possible to configure a variable or a trigger to reset the "X" axis to 0. have a good day.
Last updated: 2024-01-26

Post by timvh on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
You should only open de COM port once and then leave it open. This hCom should not keep on incrementing. (off course when you are done communicating, you need to close the COM port)
Last updated: 2024-03-22

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by eschwellinger on License Reset Request – CODESYS Control Win V3 Standard L ^{CODESYS Forge talk (Post)}
Please write these kind of request to 'my question' in the CODESYS Store. please do not use ticket and softcontainer numbers here.
Last updated: 2025-10-23

Post by eschwellinger on How to reset forgotten User Management / Administrator password on CODESYS Control Win V3 (V3.5 SP22 Patch 2)? ^{CODESYS Forge talk (Post)}
since 3.5.20.10 version you should find it here: C:\Windows\system32\config\systemprofile\AppData\Roaming\CODESYS\xxxxxxxx (64Bit) C:\Windows\SysWOW64\config\systemprofile\AppData\Roaming\CODESYS\xxxxxxxx (32Bit) you need to have admin rights.
Last updated: 2026-08-26

Post by olemart on Set REFERENCE to 0 (null) when no longer used ^{CODESYS Forge talk (Post)}
Did you find out if this work?
Last updated: 2024-10-02

Post by lsislsis on Alarms Placeholder ^{CODESYS Forge talk (Post)}
Hello. Is there any way to set placeholder for Alarms Storage at Usb Flash Disk? Regards
Last updated: 2024-10-03

Post by ivanj on Adafruit PWM library ^{CODESYS Forge talk (Post)}
Hi to all. How can I set in parameters of library abowe movement setings by angle or throttle?
Last updated: 2024-10-10

Post by kareem-pt on Velocity is too low even though correct value is reported ^{CODESYS Forge talk (Post)}
Hello, I'm playing around with a single axis. I've setup scaling and set the drive to move 360 degrees in the commissioning tab. The axis does move 360 degrees, but it moves much slower than the 360 degrees per second that I set for the velocity. It seems to be about 3 times slower (taking about 3 seconds instead of 1). This is despite the set and actual velocity both being displayed as 360. The acceleration, deceleration and jerk are all set to very high values. I'm just running this on my PC, using demo mode (no license purchased yet). I've attached a video showing the problem. Does anyone know what the problem could be? Thanks
Last updated: 2025-06-06

Post by tk096 on Velocity is too low even though correct value is reported ^{CODESYS Forge talk (Post)}
Hi, are you sure that you set up the scaling in the Scaling/Mapping tab correctly?
Last updated: 2025-06-12

Post by gepert on GearInPos ^{CODESYS Forge talk (Post)}
I solved problem. It is necessary to set MC_stop and execute mc_GearInPos for a while
Last updated: 2025-08-14

Sort by relevance or date