Post by installwhat on Panasonic servo Softmotion project ^{CODESYS Forge talk (Post)}
There are examples installed when you install codesys. they are located in C:\Program Files\CODESYS 3.5.19.50\CODESYS\CODESYS SoftMotion\Examples The examples won't be specific to your drive, though you haven't specified the exact drive. After you add the device to the ethercat master you can click on it and set pdo etc
Last updated: 2024-06-13

Post by kuegerls on SysProcessExecuteCommand2 and CANopen Device ^{CODESYS Forge talk (Post)}
I have now conducted some tests. The problem occurs when the Python script establishes an OPCUA connection, even if I only establish the connection without reading or writing any data. Is there another way to exchange data between Python and CODESYS without having to put in a lot of effort?
Last updated: 2024-06-24

Post by kaotic2499 on Upgraded Raspberry 2b to Raspberry 5, Trends Broken? ^{CODESYS Forge talk (Post)}
Is there anyone who can assist me? ill just have to raise this as a bug with codesys otherwise. I see this as the only way foward. ill attempt a fresh install of RPI in the next day or two, but thats all i had previously so 🤷‍♂
Last updated: 2025-10-21

Post by salmawis on Advice on OOP hardware I/O code structure ^{CODESYS Forge talk (Post)}
Call 10 FB instances. Connect Motor_1_Fault to the i_xHW_FaultDetected pin of FB 1, Motor_2_Fault to FB 2... By doing this, your FB will be flexible. The programming will be smooth like a perfect Drift Boss, instead of "hitting the wall" because it can't be reused!
Last updated: 2025-10-31

Post by seler on Custom button with output status ^{CODESYS Forge talk (Post)}
Hi, Im struggle with making custom button. The idea is simple grey light bulb after touch (input var) it changes to yellow but shows output var status not switch status. So if light is physically on, switched by physical switch, bulb is also yellow. How to do it?
Last updated: 2025-11-18

Post by althafu on Codesys v 3.5 to factory IO ^{CODESYS Forge talk (Post)}
I have been following the steps shown in the RealPars video to connect CODESYS with Factory I/O. The connection works correctly when I use Ladder Diagram, but when I try the same simple input–output logic in Structured Text, the simulation does not behave as expected. Has anyone experienced this issue or knows what might be causing it?
Last updated: 2025-11-20

Post by eschwellinger on Deploy LicenseServer for Linux SL ^{CODESYS Forge talk (Post)}
As I see from your logs I think the Timeprovider is not accurate enough in your case. Things to check - at the moment you run it on the same device? (for tesing purpose ok) I would set 127.0.0.0 as IP and set it not really to Core 0 ( many other stuff is there)
Last updated: 2025-11-20

Post by willebro on "Distributed clocks are not synchronized, Rea time problem on hardware" ? ^{CODESYS Forge talk (Post)}
https://forge.codesys.com/forge/talk/Engineering/thread/632c29cb93/#8d94 The above comment is the best, but if you just want to see it work you can try disabling the distributed clock. It's not the right thing to do but it should resolve that error.
Last updated: 2025-12-16

Post by s1mon on Two OneWireMaster on one Raspberry PI 5 ^{CODESYS Forge talk (Post)}
Took me a while to work on this again. I testes today with a fresh setup and it works now. My OneWireCycle tasks runs for around 10seconds. I guess my mistake was that I put the cycle task for the OneWire Task to a too small number. Thx for the support!
Last updated: 2025-11-22

Post by eschwellinger on NO SIGNAL ON POWER_ON FOR STEPPER MOTOR ^{CODESYS Forge talk (Post)}
Hi, how should that work? You need to download the example project and you need that structure of the project and one of the additional hardware sets https://forge.codesys.com/drv/sm3raspistepper/home/Home/ L298N or A4988, DRV8880. Important to have no GPIO in the project and have this additional tasks.
Last updated: 2025-11-24

Post by sturmghost on Initialization of visualization variables and cyclic code execution ^{CODESYS Forge talk (Post)}
I'm looking for a smart and short way to implement initialization of visualization variables depending on the visualization input. For an easy example consider a rectangle which rests at XPos := 0 when the input state is false and at XPos := 50 when the input state is true. My visualization variables look like this: VAR_IN_OUT State : BOOL; END_VAR VAR XPos : INT; END_VAR I put this rectangle via a visualization frame element into another visualization and link a frame reference variable with the state to it. If the variable is true, the rectangle should rest at XPos := 50 and false at XPos := 0 at visualization init but how should I assign the 50 or 0 to the internal visualization variable XPos? I would need some init-methode for the visualization but I dont want a global init-method for such tasks. I want to do it inside of the visualization element but I can't see any solution for this? It would be good to be able to define ST-code within the visualization element which runs cyclic at each VISU_TASK task-cycle then I could just check the input state and change the XPos accordingly. Does someone have a solution?
Last updated: 2023-10-01

Post by moksan on Unconnected_Send Explicit message with Route Path ^{CODESYS Forge talk (Post)}
I have been trying out Unconnected_Send Explicit Message with route path.(The Unconnected_Send service shall use the Connection Manager object in each router to forward the message and to remember the return path. Vol 1.3 / 3-5.6.7) However, I could not see the correct path on Wireshark. I want to see the Unconnected_Send Message Service Code as 0x52 and also the last of the message should have the route path. I want to ask some questions about this topic. The IIoDrvEIPAcylicServices Interface has the IoDrvSendUnconnectedMessage Method. And there is a struct (EIP_SendUnconnectedMessage) for this service. But there is no information about how to implement to project, and if it is successful, does it send a message with 0x52 Unconnected_Send Service Code or not? If that is not a solution, how can I set the Unconnected_Send Explicit Message struct on Codesys? Also how can I send explicit message with route path?
Last updated: 2023-10-17

Post by mondinmr on Jitter problems on imx8 ^{CODESYS Forge talk (Post)}
We are experiencing serious jitter issues on an ARM64 imx8. Until now, on rpi and beaglebone derivatives, and on Intel, we never encountered jitter issues unless they were already present on the device. In this case, as can be seen from the attached graph, we have excellent maximum latency. The cyclictest on the isolated core dedicated to IEC CODESYS tasks shows a latency of 37µs, with an average of 14µs. Usually, on all other devices, with an RT kernel, with the appropriate parameters to avoid frequency throttling, with properly managed IRQs, and with the disabling of large page sizes, the jitter measured by CODESYS is very close to the cyclictest latency. However, on this imx8, we are noticing a fluctuating value of +/- 300µs that seems to be added to this latency, as if something occasionally miscalculates the sleep times by exactly +/- 300µs. Two screenshoot attached. - Result of cyclictest - Jitter on CODESYS Tasks are assigned to isolated core!
Last updated: 2023-10-18

Post by martinlithlith on Mux I2C ^{CODESYS Forge talk (Post)}
Hi! I´ll try to get this thread going again as i´m having simliar problems. Right now i get a red triangle on my connected devices (i´m testing with a BME280 sensor and a PCA9685 resvo driver). The TCA9548 have the green symbol beside it. On the "red" devices i get that the bus is not running. I have tried to either run it using the parent bus cycle setting or creating a new freewheeling task prio 1 but nothing helps. I have compared my settings to the settings from the example from the MUX package and i have read (i think) every thread in forge that could be of interest. EDIT: The ic2detect only shows the mux (70-70) and the servo drive (70-76) so i´ll look in to if i managed to burn the 280-sensor while soldering). Another question regarding the 280 sensor. I have a sensor GY-BM E/P 280 that should record humidity and temperatur. Could this be a problem with the library? Does anyone have an idea of what i might be doing wrong? I have some experience from Codesys but not much so this could be an easy one. All suggestions are welcome. I tried to upload the project archive but it did not work. Should i upload the export or how could i show you my horrible project? Best, Martin
Last updated: 2023-10-22

Post by open on How to create a stopwatch? ^{CODESYS Forge talk (Post)}
Hi @ph0010421, I tried the program the TimeTaken is calculated when stop is triggered. I want the TimeTaken to be continuously calculated and counting when a BOOL variable is true. I tried to program this way: Declaration: PROGRAM PLC_PRG VAR bStartStop: BOOL := FALSE; // Start/Stop button bReset: BOOL := FALSE; // Reset button bRunning: BOOL := FALSE; // Flag indicating whether the stopwatch is running tStartTime: TIME; // Variable to store the start time tElapsedTime: TIME; // Variable to store the elapsed time END_VAR Implementation: // Main program logic IF bReset THEN // Reset button pressed, reset the stopwatch bRunning := FALSE; tElapsedTime := T#0s; ELSIF bStartStop THEN // Start/Stop button pressed, toggle the running state IF bRunning THEN // Stop the stopwatch bRunning := FALSE; ELSE // Start the stopwatch bRunning := TRUE; tStartTime := tElapsedTime; END_IF; END_IF // Update the elapsed time when the stopwatch is running IF bRunning THEN tElapsedTime := tElapsedTime + T#1s; // Adjust the time increment as needed END_IF However counting of the seconds is not accurate. I tried changing the main task cycle time interval to 1000ms. The counting of seconds become slower. (see attached) Please help
Last updated: 2023-12-08

Post by marek71 on Ambiguous use of name - CO136 ^{CODESYS Forge talk (Post)}
My PLC is WAGO PFC200 Firmware Revision 26. target After updating WAGO_Devices_and_Libraries with newer Firmware 27, CODESYS wants to update all libraries to new versions. I will only add that I did not update the Firmware in the PLC. After compiling the program, I received the following errors: ------ Build started: Application: Device.Application ------- Typify code... [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): FbSerialInterface_internal: C0136: Ambiguous use of name 'RTS_IEC_HANDLE' [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): FbSerialInterface_internal: C0136: Ambiguous use of name 'RTS_IEC_RESULT' [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): Initialize [FbSerialInterface_internal]: C0032: Cannot convert type 'Unknown type: 'RTS_INVALID_HANDLE'' to type 'POINTER TO BYTE' [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): Initialize [FbSerialInterface_internal]: C0136: Ambiguous use of name 'RTS_INVALID_HANDLE' [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): Initialize [FbSerialInterface_internal]: C0046: Identifier 'RTS_INVALID_HANDLE' not defined [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): comextra_is_tx_empty: C0136: Ambiguous use of name 'RTS_IEC_HANDLE' [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): comextra_get_line_state: C0136: Ambiguous use of name 'RTS_IEC_HANDLE' [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): comextra_is_line_available: C0136: Ambiguous use of name 'RTS_IEC_HANDLE' [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): COMSW_SET_MODE: C0136: Ambiguous use of name 'RTS_IEC_HANDLE' [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): comextra_set_line_state: C0136: Ambiguous use of name 'RTS_IEC_HANDLE' Compile complete -- 10 errors, 0 warnings Build complete -- 10 errors, 0 warnings : No download possible The problem was caused by the WagoSysPlainMem(WAGO) library in the original version 1.5.3.0 after updating to 1.5.3.1. After returning to version 1.5.3.0, the problems disappeared. Probably the version number of this library is responsible for supporting the appropriate Firmware Revision. Can anyone confirm or deny my suspicions?
Last updated: 2024-07-06

Post by programmierer on Implementing UDP Communication ^{CODESYS Forge talk (Post)}
Hello everyone, I hope you can help me with my problem. I am new to programming and am currently working with a WAGO controller in our lab, which controls a heat pump. My goal is to send the electrical power of the heat pump (Pel_WP) via a UDP connection to a specific IP address. I am using Codesys version 2.3 and following the guide I found here: https://forge.codesys.com/forum/de/396/genmed-Konfiguration%20der%20UDP%20Kommunikation%20Cosesys%20S7.pdf. I have adapted the guide to suit my needs. The data sending works since I can force the reception value Pel_WP and the data is sent accordingly. However, I am having trouble with the receiving part. The reception value is not being correctly received, and the diSocket variable shows -1. The connection between the heat pump and the WAGO controller seems to be set up correctly, as the heat pump is listed under the communication parameters with the correct IP address. I have also attached images to provide a better view of the setup. I would greatly appreciate any support or suggestions for a solution. Thank you in advance!
Last updated: 2024-08-02

Post by rossanoparis on Clarifications regarding the appropriate runtime system to use ^{CODESYS Forge talk (Post)}
Hallo all I would appreciate some clarifications regarding the appropriate runtime system to use. I've been using 'KUNBUS CPUs' and 'CODESYS Control for Raspberry Pi MC SL' for the last 4 years. Recently, there have been some changes in the CODESYS licensing policy. [ https://store.codesys.com/en/howto_applicationbasedlicenses ] My questions are mainly two: 1) If I need to start a new project using 'KUNBUS CPUs', which is the correct runtime system to use. 2) Old projects built using 'CODESYS Control for Raspberry Pi MC SL' should be updated to another RT system? Current RT systems ... a)CODESYS Control for Raspberry Pi MC SL b)CODESYS Control for Linux ARM SL c)CODESYS Virtual Control SL May I count on receiving an explanation to understand the differences among the runtime systems listed above? A detailed and well-organized answer would be greatly appreciated. Kind regards Rossano
Last updated: 2024-09-23

Post by lbartik on J1939 TX/RX PDU1 ^{CODESYS Forge talk (Post)}
Is it possible to transmit a PDU1 PGN using the J1939 manager and local device? What if I need to transmit a PGN RQST via 0xEA00 (PGN 59904)? How would I do this P2P (Destination < 0xFF) or broadcast (Destination 0xFF)? I don't think this is possible for any destination type. I don't think it's possible to receive broadcast PDU1 messages either. For example, an address claim PGN 60928 (0x18EEFF80) is addressed to all nodes (0xFF) and not any specific local device so it will be filtered out. These are major oversights in the IoDrvJ1939 library to not support every PDU1 RX/TX scenario. IoDrvJ1939 supported scenario: 1. Receive (RX) PDU1 (P2P) destination-specific (PDU-specific < 255) to local device with matching address IoDrvJ1939 unsupported scenarios: 1. Receive (RX) PDU1 (P2P) global (PDU-specific = 255) 2. Transmit (TX) PDU1 (P2P) global (PDU-specific = 255) 3. Transmit (TX) PDU1 (P2P) destination-specific (PDU-specific < 255)
Last updated: 2024-09-23

Post by egau on Hard shutdown: no code on device after power on ^{CODESYS Forge talk (Post)}
Hi, We have a machine running Codesys on a Windows IPC (CODESYS Control Win v3 - x64). When we hard shutdown the machine, the code on the PLC sometimes becomes "corrupted" after a power on (When trying to login to the PLC, we get the message "The application 'Application' does not exist on device."). I've noticed these errors in the logs, but I'm not sure what to make of them. We are not using any RETAIN variables in our code, although I'm not sure about referenced librairies. (we are using the persistence manager). I'm pretty sure that not doing a graceful shutdown is the root cause of this. This being said, what is the proper way of doing a graceful shutdown? Is putting the Codesys application in "stop" sufficient? I know how to implement this, so if it works then it would be a quick fix. However, I think we need to add a UPS, which would detect power loss and inform the PLC that it needs to initiate its shutdown, and then the PLC would shutdown gracefully. Any help with this will be greatly appreciated :)
Last updated: 2024-10-03

Post by dogulas on OPC UA C# client connecting to OPC UA CODESYS server ^{CODESYS Forge talk (Post)}
Ok, I have a simple test environment. From C#, using OPC UA, I can read DINTs, write DINTs, read Structs, but when I try to write a struct I get BadNotWritable. I am using Communication Manager, OPC UA Server, and IEC Symbol Publishing. I have a struct defined with one single DINT in it. The instance of the struct is in GVL. The struct is marked read/write in IEC Symbol Publishing. Any ideas? Pointers are welcome. public static async Task WriteStructA(byte[] structAData) { if (_session == null) throw new Exception("session is null"); // create a RequestHeader RequestHeader requestHeader = new RequestHeader { Timestamp = DateTime.UtcNow, TimeoutHint = 30000 // timeout in milliseconds }; // create an ExtensionObject to wrap the value to be written ExtensionObject extensionObject = new ExtensionObject( new ExpandedNodeId("GVL_StructA", 5), structAData ); // create a WriteValue object to hold the value to be written WriteValue writeValue = new WriteValue { NodeId = _structANodeId, AttributeId = Attributes.Value, Value = new DataValue(extensionObject) }; // put the WriteValue object into a WriteValueCollection object WriteValueCollection writeValueCollection = new WriteValueCollection() { writeValue }; // perform the write operation asynchronously WriteResponse writeResponse = await _session.WriteAsync( requestHeader, writeValueCollection, CancellationToken.None ); // check the result of the write operation if (writeResponse.Results[0] != StatusCodes.Good) throw new Exception("Write failed: " + writeResponse.Results[0]); }
Last updated: 2024-12-17

Post by mubeta on Strange problem with the ‘MC_SetPosition’ function ^{CODESYS Forge talk (Post)}
CoDeSys 3.5.19.7 Target Berghof MX6 In a simple SoftMotion programme with two stepperless modular axes from CMZ, one is simply controlled in speed, but a spot must perform a positioning. I use the function MC_SetPosition() both to reference the axis at power-up and also to correct the actual position to a fixed machine reference detected with proximity. The function has only one instance and I actually use a booelan variable to control the ‘Execute’ input. Well, I cannot correctly change the axis position on the fly if it is running at high speed. The servomotor works in a speed range between 0°/s and 720°/s, (gearbox output with a 1:6 ratio). As long as the servomotor is operating at speeds below about 400 °/s, the function is able to correct the position correctly even when forcing values far apart, but at high speeds, from 400 °/s upwards, the correction no longer takes place. For example, trying to correct the position of 280° into 300° with absolute mode, the axis that is moving at speed actually shifts the position by a few degrees, not the expected 20. I don't understand why with the servo drive running slowly the position shift occurs correctly, while increasing in speed it no longer works.
Last updated: 2025-01-09

Post by carl25 on Confused about stepper spec & tips on pwm-step/dir ^{CODESYS Forge talk (Post)}
Hello! I have asked the few I know who have knowledge of this and now turn to this one inexhaustible source of knowledge aka. the electronics forum. I was going to buy stepper motors yesterday but got so confused about the spec that I need to get an answer to this first. 2 different stepper motors, quite close in size but with very different spec. https://www.oyostepper.de/goods-40-Nema-17-Schrittmotor-Bipolar-12V-18-Grad-40Ncm-04A-12-Volt-4-Dr%C3%A4hte-Hybrid-Schrittmotor.html https://www.oyostepper.de/goods-38-Nema-17-Schrittmotor-Bipolar-18-deg-22Ncm-133A-28V-4-Dr%C3%A4hte-Hybrid-Schrittmotor.html Both Nema17 but the first 1.33A and 22Ncm and the second only 0.4A but almost double the torque. I can see that the resistance is very much higher on the latter but what's the catch? Double the torque to 1/3 the current sounds a little too good to be true so what am I missing?
Last updated: 2025-02-21

Post by egau on Enable and Disable Project IO programmatically ^{CODESYS Forge talk (Post)}
Hi @eschwellinger, I tried this with Modbus COM slaves. I was able to disable them (slave becomes greyed out in the device tree), but the DED.Reconfigure "eError" output shows "NOT_SUPPORTED". After this, when I tried to re-enable the slave, it did not work (device stayed greyed out in the device tree), and the DED.Reconfigure "eError" output also showed "NOT_SUPPORTED". Is there something to do about this, or the device just doesn't support reconfiguration? P.S: I tried this running locally on my computer (not in simulation mode). So of course I was not physically connected to the devices. I have two similar projects, but one of them doesn't have the Modbus_COM devices. I know I can "Exclude from build" the devices for that project, but I would really prefer not to do this if possible. I would prefer to dynamically toggle a configuration variable that would enable or disable the slaves.
Last updated: 2025-03-14

Post by macman on Codesys 3.5 OPC UA Client to Kepware OPC UA Server ^{CODESYS Forge talk (Post)}
Hi, I have problem with connecting Wago PLC WAGO 750-8212/0025-0002 configured as OPC UA client to Kepware OPC UA Server. I am using Codesys 3.5.19.70. What I did so far. To the Codesys project I added object Data Source Manager and configured connection OPC UA like below: pic 1 Then I can browse the OPC server tags in “Variables” tab after prior trust on the server side of the client certificate created in the “Communication” tab: pic 2 Additionally second certificate has been created in Codesys for runtime process in “Security screen” as well as the server certificate was approved here: pic 3 But when I compiled project, downloaded it to PLC and go to RUN I can’t read selected in “Variables” tab, OPC Server tags. I am getting such error (ID: 7001): pic 4 All two PLC certificates has been trusted in OPC server (Kepware) side: pic 5 and Kepware server configuration look like this: pic 6 I can easily connect using third party OPC UA client UaExpert to Kepware server without problem. In attachment I added also log from Kepware OPC UA server. pic # - this specifies the number of a concrete graphic from one of the collective in attachment
Last updated: 2025-04-02

Sort by relevance or date