Post by msirotkin on EtherCAT status errors ^{CODESYS Forge talk (Post)}
Hello, I'm trying to understand the reason for the many errors on the EtherCAT master status page. If we set the cycletime to 1ms we see a lot of rxerrors and lostframes, but the send and recive times are quite good (see attachement). And the status of the EtherCAT bus is good (no other errors, all is green, slave has no errors) But when we set 2ms cycletime the lostframe errors are gone, but periodically increses rxerror counter (see attachement). The questions is, what do these errors actually mean and what we can do to get gid of them? Linux RT, imx8, Codesys runtime for ARM 3.5.21.10, Ethercat 4.10 Thanks
Last updated: 2025-11-25

Post by mr-ege on Error: C0138: No matching 'FB_Init' method found for instantiation of VisuClientObjectMgr ^{CODESYS Forge talk (Post)}
Hi all! I'm trying to learn PLC Programing. Today I was making a simple PLC program, as you can see. When I compile the program without the visualization, there are no errors. However, when I add the visualization and then compile it, I get this error. I don’t know how to solve the problem. I have tried the following solutions: rebooting the PC and updating the software. Error Code: C0138: No matching 'FB_Init' method found for instantiation of VisuClientObjectMgr Compile complete -- 1 errors, 0 warnings Build complete -- 1 errors, 0 warnings : No download possible Version: CODESYS V3.5 SP21 Patch 3
Last updated: 2025-11-25

Post by artem1223 on Synaxis of library declarations in the ST ^{CODESYS Forge talk (Post)}
Codesys 3.5 17.30, plc - crevis GN-9373. I need to use RTC of pls for write in registers (need to check difference of writen 100 and 200 registers). For this i try to use SysTimeRtc (SysTimeRtc.SysTimeRtcGet) but its not working. After it i tryed to use SysTimeGetMs and something like this but still not working. Library? Mb but check project, SysTime with SysTimeRtc already, all what i know - already is here. Its my first try to learn ST (early used fbd and ladder, yeah), pls help with it. Mb problem with a syntaxis, but im not sure.
Last updated: 2025-11-26

Post by imdatatas on Error: C0138: No matching 'FB_Init' method found for instantiation of VisuClientObjectMgr ^{CODESYS Forge talk (Post)}
Unfortunately, the "C0138: No matching 'FB_Init" method found" error is a nightmare for CODESYS V3.5 SP21. I'm not sure if anything has been done about this or if anything will be fixed. I've encountered the same issue many times, and it was only resolved by completely uninstalling SP21, deleting all related files and folders from my computer, and then installing SP19. So, I've given up on using SP21 and switched back to SP19patch7. Here are some previous posts regarding the "C0138: No matching 'FB_Init" on SP21 of Codesys. https://forge.codesys.com/forge/talk/Visualization/thread/0763d6ca8e/ https://forge.codesys.com/forge/talk/Motion/thread/9074005bf4/
Last updated: 2025-11-28

Post by pernockham on Unable to deploy "Control for Linux SL 4.18.0.0" ^{CODESYS Forge talk (Post)}
The option to update "Control for Linux SL" is not shown in the "deploy control SL tool", I can see and update the gateway but not the control (3.5.21 SP4). Has the way to update control SL changed? In the process of fault finding I removed the control SL entirely from my target, then I had to revert to version 3.5.21.0 SP 1 to re-install "Control SL 4.17.0.0". So I thought it was just a matter of using SP1 to update also to 4.18.0.0, but after installing the files for 4.18.0.0 in the SP1-version, the behavior was identical to SP4, ie no Control for Linux SL shown in the deploy tool.. See screenshots.
Last updated: 2025-12-19

Post by eschwellinger on CmpCharDevice blocks gpiochip access on Raspberry Pi 5 since update from SP18 to SP21 ^{CODESYS Forge talk (Post)}
yes, this is a known issue which will be fixed with 3.5.23.0 .. soll will take some time. You need to switch back the runtime running not as dedicated user, like it was before 4.21.0.0 How to switch back you'll find here. ('Change service user' in the deploy tool) https://content.helpme-codesys.com/en/CODESYS%20Control/_rtsl_linux_dedicated_user.html to sumerize both problems: 1. missing entries in CODESYSControl_Usr.cfg was the problem on Raspberry PI Runtime 2. Arm64 SL is running rootless by default since 4.21.0.0 ( Pi not by default you need to switch manually if needed due this GPIO restriction)
Last updated: 2026-07-22

Post by aleksahin6824 on SysEthernet error ^{CODESYS Forge talk (Post)}
Good afternoon Please help with localizing the error. Periodically, but on the same time grid, the error SysEthernet: packet could not be sent occurs. PLC and motors from XINJE. PLC — XSA-330L, rev. 1.2, drivers — DC5C2 (rev.5) In the task configurator, all tasks are set to simple numbers (11, 13, 41 ms) for convenience. The jitter for EtherCat and SoftMotion tasks is less than the task cycle (2 ms jitter for a 6 ms task). The power supply is sufficient for both the PLC and the motors. The cables are in good condition. Please suggest where to look for the problem. P.S. The PLC uses proprietary Linux and there is no SSH access.
Last updated: 2026-08-30

Post by aleksahin6824 on SysEthernet error ^{CODESYS Forge talk (Post)}
Good afternoon Please help with localizing the error. Periodically, but on the same time grid, the error SysEthernet: packet could not be sent occurs. PLC and motors from XINJE. PLC — XSA-330L, rev. 1.2, drivers — DC5C2 (rev.5) In the task configurator, all tasks are set to simple numbers (11, 13, 41 ms) for convenience. The jitter for EtherCat and SoftMotion tasks is less than the task cycle (2 ms jitter for a 6 ms task). The power supply is sufficient for both the PLC and the motors. The cables are in good condition. Please suggest where to look for the problem. P.S. The PLC uses proprietary Linux and there is no SSH access.
Last updated: 2026-08-30

Post by pernockham on How to recognize licenses SMALL, MEDIUM, LARGE by CmpCodemeter ^{CODESYS Forge talk (Post)}
I think google has fooled me here, the only thing I can conclude so far is what i now from reading the licenseManager, which tells me that my valid license have the following product-code CONTROL - 16#3000 VISU - 16#3003, feature map: 1000 COM - 16#3004, feature map: 0200 Will different level of license give different product codes or will I see the active license level by other means? What I am trying to achieve is block Starting a machine with time limited operation should the application be larger than what the license permits (DEMO-mode). And give this information to the user by an alarm/information.
Last updated: 2026-10-06

Post by timvh on Codesys complains about matching versions ^{CODESYS Forge talk (Post)}
Open the CODESYS Installer. Create an export file from your current PC from your current version. Then on the other PC Open the installer and install a new version based on the same essentials version, but additionally select the export file which you have created on the first PC. Or just install (import) it within the already existing version. For the installer, you can install it from: https://store.codesys.com/en/codesys-installer.html For help see: https://content.helpme-codesys.com/en/CODESYS%20Installer/_inst_install_setups_and_addons.html On PC 1, save the project as projectarchive (which will then include all the libraries and devices). Then extract this projectarchive on PC 2.
Last updated: 2025-12-15

Post by reinier-geers on wEBCLIENT Post data api ^{CODESYS Forge talk (Post)}
Ive got the webclient axample. If i put https://reversed.notion.site/Marktprijzen-API-89ce600a88ac4abe8c2ad89d3167a83e example to https://reqbin.com/post-online then i get data. If i do the same in Webclient example i get " not a valid graphql request. Why ? sUrl := 'https://graphql.frankenergie.nl/' Request_type_post Contenttype = 1 (json ) Postvalue := '{"query":{"query":"query MarketPrices {\n marketPrices(date:\"2025-12-25\") {\n electricityPrices {\n from\n till\n marketPrice\n marketPriceTax\n sourcingMarkupPrice\n energyTaxPrice\n perUnit\n }\n gasPrices {\n from\n till\n marketPrice\n marketPriceTax\n sourcingMarkupPrice\n energyTaxPrice\n perUnit\n }\n }\n}' I tranfer the postvalue from String to WSTRING
Last updated: 2025-12-25

Post by julianramirez on Visu 4.9.1 auto-logon/login ^{CODESYS Forge talk (Post)}
Hello everyone, I have been trying to test the auto-login feature that is advertised on the Release Notes since Visu 4.8: *Version: 4.8.0.0 Besides some bug fixes and improvements this version contains the following new functionality: Alarmmanagement: Possibility to raise alarms programmatically Use real time clock of IEC context Automatic login for WebVisu using Chrome "Sign in automatically"* I am using a personalized login Visualization, the User Management works, however, when ticking the checkbox that keeps the credentials stored, after I reload the page I still see that the user and password details are not filled in. I tried with the default Login Visu (Blue one), and still see the same behavior - VisuUserManagement.VUM_LoginVisualization - I've tried with Chrome and Edge. Thanks for your help
Last updated: 2026-01-12

Post by sheberle on No Bootproject possible ^{CODESYS Forge talk (Post)}
Hello Alex, the message is generated by the CODESYS code generator based on the DevDesc settings of the memory areas available for the target. The problem arises when after too many online changes the area is full. Therefore no more boot project can be generated. Short-term remedy as described in the dialog: Clean and fresh download. This way the initial memory size will be "used" again After how many online changes did this error occur? There is no set limit on the number of online changes, but making too many changes could be a risk. br Simon
Last updated: 2026-03-31

Post by wistaro on Hardware compatibility with Linux RealTime PLC ^{CODESYS Forge talk (Post)}
Hello, I am currently using Codesys Control RTE Softmotion V3 to control my servo-drives in CAN, EtherCAT and PROFINET IRT. I am using a PC with Windows 10 with the following boards: - PEAK-CAN PCIe board (for CAN and Softmotion); - Hilscher CifX with firmware 3.X and SysDrv3s driver (for PROFINET IRT); - Realteak standard NIC (for EtherCAT). I would like to switch to Linux (Debian), because this computer is old, slow, and outdated (Windows 11 is far from being compatible with this computer). Before doing this, I would like to be sure of the compatility between my 3 boards and Codesys Control Linux SL. Otherwize, I will stay on Windows 10 and use it in an isolated environnement. Thanks for your advices. Regards,
Last updated: 2026-06-15

Post by charly29160 on CmpCharDevice blocks gpiochip access on Raspberry Pi 5 since update from SP18 to SP21 ^{CODESYS Forge talk (Post)}
Hallo Herr Schwellinger - Danke für die Info. Der Fehler besteht weiterhin: Follow-up: Rootless mode is not the cause here — verified with ps aux, the runtime binary runs as root: root 1974 48.9 0.7 854852 62140 ? SLl 13:00 0:04 /opt/codesys/bin/codesyscontrol.bin /etc/codesyscontrol/CODESYSControl.cfg gpioinfo gpiochip0 as root also works flawlessly (all 54 lines listed correctly, no permission errors at the kernel level). So the block is happening purely inside CmpCharDevice's own sandboxing, not at the Linux/kernel permission level and not due to a dedicated unprivileged user. The correct config key to whitelist /dev/gpiochip0 for CmpCharDevice is still what I'm looking for. Im Voraus herzlichen Dank für Ihre Hilfe Karl Schuler
Last updated: 2026-07-20

Post by charly29160 on CmpCharDevice blocks gpiochip access on Raspberry Pi 5 since update from SP18 to SP21 ^{CODESYS Forge talk (Post)}
Hallo Herr Schwellinger - Danke für die Info. Der Fehler besteht weiterhin: Follow-up: Rootless mode is not the cause here — verified with ps aux, the runtime binary runs as root: root 1974 48.9 0.7 854852 62140 ? SLl 13:00 0:04 /opt/codesys/bin/codesyscontrol.bin /etc/codesyscontrol/CODESYSControl.cfg gpioinfo gpiochip0 as root also works flawlessly (all 54 lines listed correctly, no permission errors at the kernel level). So the block is happening purely inside CmpCharDevice's own sandboxing, not at the Linux/kernel permission level and not due to a dedicated unprivileged user. The correct config key to whitelist /dev/gpiochip0 for CmpCharDevice is still what I'm looking for. Im Voraus herzlichen Dank für Ihre Hilfe Karl Schuler
Last updated: 2026-07-20

Post by konstantin on Lenze i950 Servo and WAGO PFC200 ^{CODESYS Forge talk (Post)}
Hello, basically the i950 drive support CiA402 Basic and CiA402 Advanced modes. I attached pictures of both mode supported functions. It also support CSP, VL, CSV and CST modes. It seems the homing mode is in CiA402 Advanced mode but how can you not have the homing mode in both modes? It is a vital part of any servo system. If I use the SoftMotion standard demo mode, I can move the servo absolute and relative but cannot home it. But in SoftMotion Light mode, I cannot execute any motion function. Here is the official manual for i950 servo drive - i950 Documentation Best Regards Konstantin Kolev
Last updated: 2026-02-13

Post by gseidel on Absolute movement controlled by an external encoder. ^{CODESYS Forge talk (Post)}
Hi polyautomacao, basically, there are two ways to approach this. My first choice would be to check whether your servo drives supports an external encoder, connect the encoder to the servo and configure the servo accordingly. In this case, you would not need to change anything in the CODESYS application. If that is not an option, you could use SM_DrivePosControl, a drive that closes the position loop in the PLC, and feed it with the external encoder positions. See (0). You can switch your servo drive to velocity control mode (SMC_SetControllerMode) and use SMC_FollowVelocity to apply the fSetVelocity of the SM_DrivePosControl to your servo. The MC_MoveAbsolute can then be performed on the SC_DrivePosControl Hope that helps. (0) https://content.helpme-codesys.com/en/CODESYS%20SoftMotion/_sm_example_poscontrol.html Best regards, Georg
Last updated: 2026-03-04

Post by hannibal on Codesys Trend - setting Y axis minimum and maximum as variables - error ^{CODESYS Forge talk (Post)}
I am experiencing an issue when trying to define the Y-axis limits in a Trend Graphic using variables. When I set the Minimum and Maximum values as variables, an error is triggered. My goal is to make the Y-axis limits dynamic so they can adjust according to the installation. Both variables are initialized as follows: gP_YMin = -100.0 gP_YMax = 100.0 However, I still get the following error: "The minimum axis value must be less than the maximum axis value" Does anyone have an idea why this is happening or how to resolve it?
Last updated: 2026-03-22

Post by hannibal on Codesys Trend - setting Y axis minimum and maximum as variables - error ^{CODESYS Forge talk (Post)}
I am experiencing an issue when trying to define the Y-axis limits in a Trend Graphic using variables. When I set the Minimum and Maximum values as variables, an error is triggered. My goal is to make the Y-axis limits dynamic so they can adjust according to the installation. Both variables are initialized as follows: gP_YMin = -100.0 gP_YMax = 100.0 However, I still get the following error: "The minimum axis value must be less than the maximum axis value" Does anyone have an idea why this is happening or how to resolve it?
Last updated: 2026-03-22

Post by alexgooi on Network variable stops sending ^{CODESYS Forge talk (Post)}
Hi Reinier, What usually works for me is settings it up in the following way: In the sender block make sure that the list identifier is unique for the whole installation (this is only relevant when you have multiple senders in 1 network). When you are linking the NVL to a file make sure that the path to this file doesn't change. In my experience the NVL stops working when you change the working directory and afterwards open the NVL in de Codesys IDE. If this doesn’t apply to you application, you could also try to change the port number, maybe there is an other process making use of port 1202. Kind regards Alex
Last updated: 2026-04-22

Post by timvh on library inside library ^{CODESYS Forge talk (Post)}
1) it should be possible to access the type SysTime in the project as A_Lib.SysTime. 2) you could add the SysTimeCore library to the library manager of your library (POU Pool). This might seem as a double library, but because of the placeholder resolution only one will be used. Then, in your library manager of your library, select the SysTimeCore library, right-click, select "Properties" and enable the option "Publish all IEC symbols ...." For more information about library development, you could follow our advanced training course in Ridderkerk. The next is scheduled for 24 and 25 June 2026 https://www.extendsmartcoding.nl/codesys-training/
Last updated: 2026-04-25

Post by kurt9 on ReadWriteEEprom FB question ^{CODESYS Forge talk (Post)}
I want to programmatically write the alias address to a new EtherCAT slave when I plug it into my IPC EtherCAT network. I am looking at the ReadWriteEEprom FB and see that one of the elements is "pbyData". which is the pointer to byte that is usually set to 2048 bytes. Since I am setting the alias address to the EEprom only (EEprom address 16#0012), I would assume that what I am writing is 2 bytes only. Does the pbyData have to be specified as ADR(myArray) where "myArray" is the 2 bytes of the alias address? How is the best way to set this element of the function block? Thanks in advance
Last updated: 2026-05-18

Post by jroddball79 on PM556-TP-ETH — How to change IP address without overwriting the PLC program? ^{CODESYS Forge talk (Post)}
We have checked open ports. SSH (22) and HTTP (80) are not reachable. The only open ports are: 502 (Modbus TCP — used for lighting control) 1200 (CODESYS runtime) 1201 (CODESYS runtime) We can connect via Automation Builder using the current IP, but we don't have the original project source — only an empty project. This is why we are afraid of doing a full download, as it would overwrite the running application. Is there any way to change the IP through the CODESYS runtime protocol on ports 1200/1201 without affecting the running program?"
Last updated: 2026-05-20

Post by brouwyka on JSONByteArrayWriter problem? ^{CODESYS Forge talk (Post)}
Hey there! I am currently running into the exact same issue. The JsonData object has all inexes & parent indexes in the way I expect, everything is correctly "linked". It purely seems that the writer is incorrectly parsing said JsonData, not based on parent & child index, but on something else that breaks it and puts things at the root, instead of the specified parent index. Did you ever manage to find a solution, or another way of achieving your JSON composing? I'm currently working on Codesys V3.5 SP19 Patch 7 with IIOT Libraries SL 1.13.0.0, specifically JSON Utilities SL 1.13.0.0 (to send requests to APIs with JSON bodies using Web Client SL 1.13.0.0).
Last updated: 2026-06-08

Sort by relevance or date