Post by davidbo on How to stay in a method until something is finished. ^{CODESYS Forge talk (Post)}
You never stay in a method. You need a block to do that. Something like: VAR button:BOOL:=FALSE; count:UINT:=0; END_VAR IF button THEN //read pressure count:=count+1; IF count>1 THEN button:=FALSE; count:=0; END_IF END_IF
Last updated: 2025-11-04

Post by micik on Using Codesys example problems ^{CODESYS Forge talk (Post)}
Hello to all, I'm totally new to Codesys, but I do have some PLC programming experience, mosty with Siemens TIA and STEP7. I have just installed Codesys 3.5. sp19 and I have downloaded example with Ethernet Rockwell 1734AENT. The example can be found here: https://forge.codesys.com/prj/codesys-example/rockwell-1734-c/home/Home/ After opening, I had to manually update devices (Device, Ethernet, IP Scanner, EthernetIP adapter). However, when trying to build the project, I get the following errors: [WARNING] CODESYS_EtherNetIP_Rockwell1734AENT: Library Manager [Device: PLC Logic: Application]: C0100: Library System_VisuElemXYChart has not been added to the Library Manager, or no valid license could be found [WARNING] CODESYS_EtherNetIP_Rockwell1734AENT: Library Manager [Device: PLC Logic: Application]: C0100: Library system_visuinputs has not been added to the Library Manager, or no valid license could be found [ERROR] iodrvethernetip, 4.4.1.0 (3s - smart software solutions gmbh): ServiceCycle [IoDrvEtherNetIP]: C0040: Function 'ProcessUpdateConfigurationQueue' requires exactly '1' inputs [ERROR] iodrvethernetip, 4.4.1.0 (3s - smart software solutions gmbh): IoDrvStartBusCycle [IoDrvEtherNetIP]: C0040: Function 'GenerateRandomUINT' requires exactly '2' inputs [ERROR] iodrvethernetip, 4.4.1.0 (3s - smart software solutions gmbh): Cyclic [GenericServiceUnConnected]: C0040: Function 'GenerateRandomUINT' requires exactly '2' inputs [ERROR] cip object, 4.4.1.0 (3s - smart software solutions gmbh): ForwardOpenService [ConnectionManager]: C0040: Function 'GetAssemblies' requires exactly '3' inputs [ERROR] iodrvethernetipadapter, 4.4.0.0 (3s - smart software solutions gmbh): ServiceCycle [IoDrvEtherNetIPAdapter]: C0040: Function 'GenerateRandomUINT' requires exactly '2' inputs [ERROR] iodrvethernetip, 4.4.1.0 (3s - smart software solutions gmbh): SetupStructuredIOMapping [RemoteAdapter]: C0040: Function 'MallocData' requires exactly '1' inputs [ERROR] iodrvethernetip, 4.4.1.0 (3s - smart software solutions gmbh): SetupStructuredIOMapping [RemoteAdapter]: C0040: Function 'MallocData' requires exactly '1' inputs Compile complete -- 7 errors, 13 warnings Build complete -- 7 errors, 13 warnings : no download possible! What could be the reason for this errors and how to rectify them? Thank you!
Last updated: 2024-02-01

Post by e13740e on Сalling the context menu from the keyboard ^{CODESYS Forge talk (Post)}
Hello. I have a question for you, perhaps you have an answer to it. Regarding calling the Context menu from the keyboard in Devices, specifically calling the context menu window from the keyboard via an assigned combination. Goal: to have the ability to navigationally add internal Objects (Methods, Properties) to Function Blocks from the keyboard without using the mouse. The Codesys environment interface does not allow Windows access to this via Shift+F10. Externally (outside the Codesys environment), the hotkey call for the context menu (Shift+F10) from the keyboard works in various environments, but at the same time, in Codesys it does not (it doesn't work). I have already tried various options on my own to achieve this (but unsuccessfully): Tools\Customize\Keyboard\Objects (the set combination does not give the desired result) Tools\Customize\Keyboard\Objects... (the set combination is extremely useful as it provides access to adding objects directly to Devices but does not provide the ability to add an internal object (Method/Property) to a Function Block). Thank you in advance for your help!!! P.S. I have already started trying to implement a script-based solution to call the context menu via AutoHotkey - by relocating the mouse cursor to the area of the navigational selection with a subsequent call of the context menu on it and relocating the mouse cursor back to its initial position. And in order not to "reinvent the wheel," I am writing this request to you!!!
Last updated: 2025-10-05

Post by e13740e on Сalling the context menu from the keyboard ^{CODESYS Forge talk (Post)}
Hello. I have a question for you, perhaps you have an answer to it. Regarding calling the Context menu from the keyboard in Devices, specifically calling the context menu window from the keyboard via an assigned combination. Goal: to have the ability to navigationally add internal Objects (Methods, Properties) to Function Blocks from the keyboard without using the mouse. The Codesys environment interface does not allow Windows access to this via Shift+F10. Externally (outside the Codesys environment), the hotkey call for the context menu (Shift+F10) from the keyboard works in various environments, but at the same time, in Codesys it does not (it doesn't work). I have already tried various options on my own to achieve this (but unsuccessfully): Tools\Customize\Keyboard\Objects (the set combination does not give the desired result) Tools\Customize\Keyboard\Objects... (the set combination is extremely useful as it provides access to adding objects directly to Devices but does not provide the ability to add an internal object (Method/Property) to a Function Block). Thank you in advance for your help!!! P.S. I have already started trying to implement a script-based solution to call the context menu via AutoHotkey - by relocating the mouse cursor to the area of the navigational selection with a subsequent call of the context menu on it and relocating the mouse cursor back to its initial position. And in order not to "reinvent the wheel," I am writing this request to you!!!
Last updated: 2025-10-05

Post by manuknecht on Maximum dynamic limits of MC_MoveLinearAbsolute and MC_MoveLinearRelative ^{CODESYS Forge talk (Post)}
Hello all I use an axis group with two linear axes in a kinematic system. Using MC_MoveLinearAbsolute and MC_MoveLinearRelative, I am trying to realise dynamic movements (set velocity: 1 m/s, set acceleration: 30 m/s^2) with the highest possible jerk, as I want to compare this with a movement with a trapezoidal velocity profile. However, my measurements show that the axes accelerate with a maximum jerk of approx. 800 m/s^3, even if the value in the function block was set to 10,000 m/s^3. I have already increased the dynamic limits of the two axes accordingly (Velocity: 5000 u/s, Acc-/Deceleration: 250'000 u/s^2, Jerk: 100'000'000 u/s^3, where 1 u = 1 mm), but this had no effect. I have checked the input parameters of the function blocks and the VelFactor, AccFactor and JerkFactor factors are all set to the maximum (value 1). Reducing the cycle time has resulted in a higher jerk, but as we are already working with a cycle time of 1 ms, there is nothing more that can be done here. The axes themselves are still a long way from drawing the maximum current, which is why I assume that this should not be a problem either. Are there other factors or parameters that influence the dynamic limits and therefore allow faster movements? The PLC I am using is a Raspberry Pi 4 and Codesys V3.5 SP20 with all libraries up to date. Thanks in advance Manuel
Last updated: 2024-05-08

Post by davidbo on How to allow a user to handle certificates without access to sourcecode? ^{CODESYS Forge talk (Post)}
With CODESYS V3.5 it is possible for a user to do the following things among many others. 1) Handling certificates especially move a certificate to the trusted folder. 2) Change password and create new users for OPC UA access However it requires access to the whole projects and its source code. Something you might not want to hand over to an end user for a stand alone product. Is there a way out of this problem?
Last updated: 2023-11-06

Post by gepert on parker servo and position ^{CODESYS Forge talk (Post)}
Hello, Thank you for your response. In my application i use ethercat and while work i do not turn off power. After relative move motor is in standstill. As you suggest I suppose that problem is in drive setting but i do not see any option about increase standstill torque. Below i posted some photos from drive setting manager - PSD Servomanager Do you see any settings responsible for standstill torque? thank you
Last updated: 2024-08-05

Post by trusty-squire on implementing continuous movement in Codesys ^{CODESYS Forge talk (Post)}
What do you mean by continuous movement? You want to continuously follow a dynamic target position? SMC_ControlAxisByPos, which is typically used with CNC Interpolators, could work for that. Instead of feeding the target position in from the Interpolator, feed in the target position from your server instead. Once you enable the FB, it will continuously move the axis to track the fSetPosition input. https://content.helpme-codesys.com/en/libs/SM3_CNC/Current/SM_CNC_POUs/SoftMotion-CNC/Direct-Axis-Control/SMC_ControlAxisByPos.html
Last updated: 2024-09-12

Post by pmanuele on Beckhoff AS1060 and EL7041 configuration ^{CODESYS Forge talk (Post)}
Hello everyone, i'm having some problems commanding AS1060 step motor with EL7041 (rev22) drive. With motor i've also the incremental encoder (05.2420.1230.0200.5009). I can correctly move the motor in "Position controller" operating mode with the internal counter. The problems start when i set the Encoder in feedback type or i change the operating mode. Does anyone have experience with these two terminals and can give me some advice of main parameters to check or change? Thanks everyone
Last updated: 2024-12-11

Post by wayne-riesterer on Assignment Efficiency - Repetitive Assignment vs IF statement ^{CODESYS Forge talk (Post)}
Hello Can anyone see any problems with constant assignment as in the following statement: Coils[0] := Coils[0] OR (Buttons[0] AND Sensors[0] > 6); Rather than using the more verbose and vertically-larger: IF NOT Coils[0] AND Buttons[0] AND (Sensors[0] > 6) THEN Coils[0] := TRUE; END_IF Also, is the test expression short-circuited in the latter case? In other words, will the runtime move on after it sees Coils[0] = FALSE AND? Thanks
Last updated: 2025-03-07

Post by nz-dave on ethercat softmotion axis error ^{CODESYS Forge talk (Post)}
Hi all I'm having a little trouble get my axis to work. i can turn them off and on. i can run each servo manually inputting directly to the mapping address. as soon as i try to use any FB's like jog etc my servos wont move and error out. so far I've had error "SMC_ERROR.SMC_DI-POSITIONLAGERROR" and another one about not calling a fb. cheers. in the attachment I have just jogged X_Axis with the MC_JOG FB
Last updated: 2025-03-10

Post by food on Beaglebone Black OPC-UA Server ^{CODESYS Forge talk (Post)}
Man, this was a long time ago. I think the problem probably stemmed from not loading the certificates from the client and the server on the server and client respectively in the correct manner. I believe I ended up getting around it just by removing all security on the server. In the end we did not move forward with that architecture so I never had to actually fix it.
Last updated: 2024-04-10

Post by mizi on SM_Drive_Virtual ^{CODESYS Forge talk (Post)}
Hi I recently started learning Codesys SoftMotion. At first, I mainly used YouTube videos. I stopped at two videos where the same problem keeps recurring. fbReadPos( Axis := X_Axis, Enable := TRUE, Position => gAxes.lrActualPos); <- axis cannot move I checked the entire code line by line. Zero errors. GPT spits out nonsense, throwing up increasingly worse errors. And when I copy its code, it says the code is wrong and gets stuck in a loop of its own stupidity. Can anyone explain why it doesn't work? Link to the video below: https://www.youtube.com/watch?v=CYa2HvYZgbM&list=PLsEhEcYjG7na0OveU7cqFXBx7ATyGGn0A&index=3
Last updated: 2025-10-21

Post by ducng on SMC_FB_WASNT_CALLED_DURING_MOTION when enable MC_MoveRelative ^{CODESYS Forge talk (Post)}
Hello, I am using an Inovance PLC to control a servo via EtherCAT. When I enable MC_POWER, the drive switches to Run mode successfully. After that I call MC_MoveRelative, but I get the error SMC_FB_WASNT_CALLED_DURING_MOTION. The servo vibrates but the motor shaft does not move. I am new to EtherCAT/servo motion control, so I would appreciate any guidance or suggestions for troubleshooting this issue. Thank you in advance for your help.
Last updated: 2025-11-02

Post by otbeka on CmpCrypto CryptoGenerateHash Not Outputting ^{CODESYS Forge talk (Post)}
Unfortunately I noticed that, and tried: * using CryptoGeteAlgorithmByID within the function call * inputting the raw byte pointer as a testByte * instantiating the _hHash handle within the function body * using a different cryptoID or the raw DINT values from the RtsCryptoID DUT ... to no avail. The pReturn value is also set to 0, which would indicate that it is OK, right? This is odd given that the function is the same within the CryptoDemo example project here, just with a newer version. Is it possible that there is something wrong with the way my bytestring is being set up? I use the following DUTs here: TYPE MESSAGE : STRING(255); END_TYPE TYPE HASH_CODE : ARRAY[0..19] OF BYTE; END_TYPE
Last updated: 2024-09-06

Post by sebastianrapi on Bibliothek: floatingpointutils ^{CODESYS Forge talk (Post)}
@Strucc.c: thanks very mutch. Yes, I think that was the problem. I tried yesterday a similar function, i have found: IEEE32 in REAL FUNCTION IEEE32_TO_REAL : REAL VAR_INPUT IN:DWORD; END_VAR VAR PTREAL:POINTER TO REAL; END_VAR PTREAL:=ADR(IN); IEEE32_TO_REAL:=PTREAL^; END_FUNCTION REAL in IEEE32 FUNCTION REAL_TO_IEEE32 : DWORD VAR_INPUT IN:REAL; END_VAR VAR PTDWORD:POINTER TO DWORD; END_VAR PTDWORD:=ADR(IN); REAL_TO_IEEE32:=PTDWORD^; END_FUNCTION http://www.oscat.de/community/index.php/topic,357.0.html And this works perfect. Now, the only thing that isn't clear is the libary "FloatingPointUtils, 3.5.17.0 (System)"... For me, the libary doesn't work. But the problem is now solved. Thanks a lot.
Last updated: 2024-11-21

Post by bingo on PLC Shell commands via ST Code ^{CODESYS Forge talk (Post)}
Suppose you need to switch PLC IP dynamically between 192.168.1.10\192.168.2.10, First, set PLC IP to 192.16.1.10. Create a PGVL with a flag ‘xUseSecondry’ xUseSecondry : bool ; create a function that use socket to update IP: FUNCTION fSwitchIP : bool VAR_INPUT useMainIP:bool; END_VAR --------------------------------CODE------ if useMainIP then SysSockSetIPAddress(‘0’, ‘192.168.1.10’); PGVL.xUseSecondry := 0; else SysSockSetIPAddress(‘0’, ‘192.168.2.10’); PGVL.xUseSecondry := 1; end_if Now, if during execution, you need to switch IP, call the function ‘fSwitchIP()’, Set input to 1 for main IP, 0 for secondary IP. In order to set secondary IP at startup, you can do the following: in your PLC_PRG add a flag: xInit : bool := 1 ; and the code: if xInit then if PGVL.xUseSecondry then fSwitchIP(0); end_if xInit := 0 ; end_if *Alternative way is to use system events.
Last updated: 2025-03-03

Post by user3000 on Can't find an Extended Pulse Timer (TP and LTP) ^{CODESYS Forge talk (Post)}
Hello, For my program I need an extended pulse timer, which can be referred to as a retriggerable pulse timer. Where every rising edge of the input resets the elapsed time zero, extending the lenght of the output pulse. The Codesys pulse timer (TP) is a one-shot timer and only resets the elapsed time with the falling edge of the input. There is also a pulse timer (LTP) in codesys, but in my simulation it was also functioning as a one-shot even though the description sounds like LTP should be retriggerable. I have uploaded some timing plots from another PLC program for reference. I am looking for a timer equivalent to the "TEP" diagram. Is there an Extended Pulse Timer in Codesys? Maybe there is a way to manipulate the input so it resets the elapsed time outside the function block?
Last updated: 2023-12-06

Post by abinvest579 on TCP Client ^{CODESYS Forge talk (Post)}
Hi All, I am using codesys based plc to read and control magna power DC supply over LXI protocol using SCPI command. To connect device required socket programming for that i am using Net base service library function block TCP_Client to establish connection over TCP/IP , TCP_Write to write SCPI commands and TCP_Read to read data from Magna power DC supply. I have attached screenshot for logic developed. I am able to connect and write commands to device but i not receiving any information from device. For writing Commands i also tried various end of line character like \n,<nl>, A, D, 10, 13, 0x0A, 0x0D but not received any status from device. For testing purpose i am using simple command '*IDN?' to read data. Also if tried to check on hercules software what data actually plc read, first it read correct data after that is read wrong data as see in screen shot. 'Hello World' was correct read and after that Codesys in replaced with 'Codesysorld' that is not correct way. Same issue also appeared for send data. Any one have face same issue how i can read data directly from device correctly and send data please suggest solution on this.</nl>
Last updated: 2024-07-01

Post by timvh on How to implement an interface (IElement)? ^{CODESYS Forge talk (Post)}
See: https://forge.codesys.com/prj/codesys-example/element-collect/home/Home/ This contains an application "OnlineChangeSafeLinkedListExample". What you should do is create a new interface which has your "Priority" property. Then your FB should extend the base element function block and implement your own interface: E.g. FUNCTION_BLOCK MyElement EXTENDS COL.LinkedListElementBase IMPLEMENTS I_MyInterface Then the __QUERYINTERFACE does the magic to check if your "element" also implements your interface. Something like this: // Compares this element with itfElement. // Returns 0 if the elements are equal, < 0 if the element is less than itfElement, // > 0 if the element is greater than itfElement. // This method will be called from sorted collections (e.g. |COL.SortedList|) to sort the elements. // IMPORTANT: The underlying value to be compared with MUST NOT be changed during the lifecycle of the object. METHOD ElementCompareTo : INT VAR_INPUT (* The element to compare*) itfElement : COL.IElement; END_VAR VAR itfIntElement : I_MyInterface; xResult : BOOL; END_VAR // We use integer iInt1 for sorting. xResult := __QUERYINTERFACE(itfElement, itfIntElement); IF xResult THEN IF iInt1 < itfIntElement.Priority THEN ElementCompareTo := -1; ELSIF iInt1 > itfIntElement.Priority THEN ElementCompareTo := 1; ELSE ElementCompareTo := 0; END_IF ELSE ElementCompareTo := -1; END_IF
Last updated: 2024-07-22

Post by ruobian on Analog Input Delay Timer ^{CODESYS Forge talk (Post)}
Hello there, I am new here and in programming. I need help with the basics. I am trying to do what I mentioned in the title. I have an analog input. So I have a real or integer data type value. I want to delay it. TON and TOF only work with bool. I think there is a function block that has two inputs, 1 for real or int and 1 for bool. And if bool is true, it will give the output as real or int. I don't know but I need something like this. Actually, it is not exactly like that. In other words, it will not show the real value at the input at the output after a certain period of time. I want it to show the real value from 2 seconds ago continuously. The purpose of doing this is to compare the real value I received with the value from 2 seconds ago and find out whether it went up or down. I am using only FBD. Please help me with this. Thanks in advance.
Last updated: 2024-08-20

Post by ellocco on XOR with four Inputs with OR-, NON- and AND-Operators ^{CODESYS Forge talk (Post)}
My topic is more of academic nature, I would like to implement an XOR-operation with four inputs on my own (without the predefined XOR-operator) in a function block diagram (FBD). I have two proposals. One works fine and the other one is just an idea, but I do not know, if it is possible to code it in CODESYS V3.5 SP18 in form of a FBD. Here the one that works: And here an idea, which I have not managed to code it as an FBD: Any ideas? Is the 2nd diagram a correct interpretation of the coding task? And is there a way to implement it in form of an FBD in CODESYS V3.5 SP18? Followup (08-Nov-2024): Also in the current version of CODESYS (V3.5SP20Patch3) I have not managed to connect the existing blocks. In the alternative SPS-IDE PLCnext Engineer it is possible.
Last updated: 2024-11-08

Post by laurits on Max lines of code, codesys CNC ? ^{CODESYS Forge talk (Post)}
Hi, okay here's the project, it's a modified version of "CNC Example 10: Programming Dynamic CNC Paths", no need for G Code text file (i have also tried with G code text file, same problem) in "PROGRAM PLC_PRG" you can set bStart to true, and the program should start running, go to "PROGRAM CNC" and you can see axis moving. lrXpos := IoConfig_Globals.XAixs.fSetPosition; lrYpos := IoConfig_Globals.YAxis.fSetPosition; Now you can can change the number of movements in the the "PROGRAM PLC_PRG" From this number of movements in "program PLC_PRG" BUF : ARRAY[0..32010] OF SMC_GEOINFO; xp : ARRAY[1..32000] OF REAL; yp : ARRAY[1..32000] OF REAL; to this number to this number of movements BUF : ARRAY[0..132010] OF SMC_GEOINFO; xp : ARRAY[1..132000] OF REAL; yp : ARRAY[1..132000] OF REAL; Now if you start the program again you should see an error in the "sMC_Interpolator: SM3_CNC.SMC_Interpolator;" function block Let me know if you can not get it running.
Last updated: 2025-06-03

Post by brell on Automatic xExecute NBS.TCP_write ^{CODESYS Forge talk (Post)}
I've recently started experimenting with CODESYS for a project and am fairly new to it. I'm currently working with Function Block Diagrams (FBD) to set up TCP communication between a server and a client, where the client is implemented as a Python script. Once the communication is established, my connection status changes to True, which is the expected behavior. My challenge arises with the TCP write module, which requires the xEnable_write flag to toggle between True and False. If xEnable_write remains True, the module only performs a single write operation. To address this, I introduced a falling edge trigger (F_TRIG), expecting it to help in toggling xEnable_write and it does, However, I've encountered an issue where in the beginning after connxion established I need to manually set xEnable_write to True for the system to work as intended. I'm looking for a way to automate this process so that xEnable_write becomes True automatically upon establishing a connection . Initially, I tried setting xEnable_write to True from the start, but this approach didn't work well since it left the flag permanently True, preventing further toggling. I also experimented with using a TON timer, but I faced similar issues. I am seeking a solution that automatically toggles xEnable_write between True and False after a connection is established, ensuring continuous write operations without manual intervention. Any advice or guidance on how to achieve this would be greatly appreciated."
Last updated: 2024-03-05

Post by mtho on JSON Utilities - JSON file written with invalid structure ^{CODESYS Forge talk (Post)}
I'm using the JSON Utilities SL library to write configurations in my program to a file. I'm generating the JSON data using the builder function block and all appears to work correctly. When I write the jsondata to file, I'm finding that some of the JSON elements are not being written in the right location in the file. Rather than writing they keys under the parent object, they get written outside the root JSON object at the end of the file. If I then try to read the file back into the program, I get an invalid_structure error. I don't get any errors when populating the JSON data or when writing the file. I attached an example of the JSON writer output. The problems begin with key P200. Each P200 should go under MBR1 through MBR3. Among the rest of the keys, they are supposed to be under different parent objects. I am using default values for wsLineBreak and encoding.
Last updated: 2024-03-06

Sort by relevance or date