Post by greenwood on CODESYS Control Raspberry Pi mit Servotreiber T6 von StepperOnline ^{CODESYS Forge talk (Post)}
Hallo, Ich scheine den Grund gefunden zu haben, das Kabel mit dem RJ45 Stecker ist für RS232 verdrahtet (am anderen Ende des Kabels ist ein 9-poliger SUB-D Stecker, nicht wie von mir im Eingangspost behauptet ein USB Stecker). In der Anleitung des Treibers ist immer nur von RS 485 die Rede. Alerdings habe ich es gestern abend noch geschafft eine funktionierende Version der setup-software herunterzuladen, und die verbindet sich offenbar über RS232. Daraufhin habe ich mir in der Anleitung des Treibers das Pinout der RJ45 Buchse nochmal angesehen, und die hat Kontakte für RS232 und für RS485. (Die liegen jeweils ganz am Rand, so ist mir das vorher nicht aufgefallen). Ich muss also als Nächstes ein richtig verdrahtetes Kabel auftreiben, und dann sehen ob das mit dem Adapter den ich habe funktioniert. An einen Abschlusswiderstand habe ich auch schon gedacht, nur weiss ich nicht wo ich den an einem RJ45 Stecker / Buchse - Paar anbringen soll... Ich bitte um Entschuldigung für die Verwirrung, ich mache das alles zum ersten Mal und es ist ganz schön viel auf einmal für mich. Nochmal vielen Dank für die Unterstützung!
Last updated: 2024-06-01

Post by paulg on RasPi CAA Serial example - unexpected behavior during debug ^{CODESYS Forge talk (Post)}
I've trimmed down the CAA Serial Codesys example to only listen on one port but, when stepping through the Case structure in debug mode, it jumps out of the structure during a specific point in every scan (I'll point it out below after describing the setup and listing the code). I'm using a Pi 4 Model B, and I have an Arduino Nano Every plugged in via USB which is streaming the following serial message at 1 Hz: Time since opening connection: 1 s Time since opening connection: 2 s ...and so on. The Pi shows the Nano at /dev/ttyACM0 so I edited CODESYSControl_User.cfg to read: Linux.Devicefile=/dev/ttyACM The code in my PLC_PRG is (ignore some of the comments, I hadn't deleted them out from the original example): PROGRAM PLC_PRG VAR xStartTest : BOOL:= TRUE; iState : INT; xTestDone : BOOL;(* True, when the test was done succesfully *) (* Settings to communicate with the COM Port *) aCom1Params : ARRAY [1..7] OF COM.PARAMETER; como1 : COM.Open; comc1 : COM.Close; comw1 : COM.Write; comr1 : COM.Read; //sWrite : STRING := 'Test String!'; sRead : STRING(25); szRead : CAA.SIZE; xCom1OpenError : BOOL; xCom1CloseError : BOOL; xCom1WriteError : BOOL; xCom1ReadError : BOOL; END_VAR //This example shows the communication of two COM Ports with each other. //The first one writes a string of characters, which is read by the second one. //After successful execution, the two COM Ports are closed and the test is done. IF xStartTest THEN CASE iState OF 0: //The parameters are set for the COM Port aCom1Params[1].udiParameterId := COM.CAA_Parameter_Constants.udiPort; aCom1Params[1].udiValue := 1; // the correct Port should be adapted aCom1Params[2].udiParameterId := COM.CAA_Parameter_Constants.udiBaudrate; aCom1Params[2].udiValue := 115200; aCom1Params[3].udiParameterId := COM.CAA_Parameter_Constants.udiParity; aCom1Params[3].udiValue := INT_TO_UDINT(COM.PARITY.NONE); aCom1Params[4].udiParameterId := COM.CAA_Parameter_Constants.udiStopBits; aCom1Params[4].udiValue := INT_TO_UDINT(COM.STOPBIT.ONESTOPBIT); aCom1Params[5].udiParameterId := COM.CAA_Parameter_Constants.udiTimeout; aCom1Params[5].udiValue := 0; aCom1Params[6].udiParameterId := COM.CAA_Parameter_Constants.udiByteSize; aCom1Params[6].udiValue := 8; aCom1Params[7].udiParameterId := COM.CAA_Parameter_Constants.udiBinary; aCom1Params[7].udiValue := 0; //The first Port is opened with the given parameters como1(xExecute := TRUE, usiListLength:=SIZEOF(aCom1Params)/SIZEOF(COM.PARAMETER),pParameterList:= ADR(aCom1Params)); IF como1.xError THEN xCom1OpenError := TRUE; iState := 1000; END_IF //After a successful opening, the next state is reached IF como1.xDone THEN iState := 15; END_IF 15: // the reading process is started comr1(xExecute := TRUE,hCom:= como1.hCom, pBuffer:= ADR(sRead), szBuffer:= SIZEOF(sRead)); IF comr1.xError THEN xCom1ReadError := TRUE; END_IF //After completion the size of the written bytes are saved IF comr1.xDone OR comr1.xError THEN szRead := comr1.szSize; iState := 20; END_IF 20: // If everything was successful the ports are closed and the handles are released comc1(xExecute := TRUE,hCom:= como1.hCom); IF comc1.xError THEN xCom1CloseError := TRUE; END_IF IF comc1.xDone OR comc1.xError THEN iState := 25; END_IF 25: // The first port is closed and the used handle released xTestDone := TRUE; xStartTest := FALSE; iState := 0; como1(xExecute := FALSE); comw1(xExecute := FALSE); comc1(xExecute := FALSE); ELSE iState := 0; END_CASE END_IF I realize as I write this that the .udiPort should be 0 and not 1, but that shouldn't be causing the issue I'm seeing. I'm forcing xStartTest:=TRUE every scan so that I can step into each line and observe what's happening. What I see is that the port parameters are set and the port is opened with no errors, but the code jumps out of the case structure to the last line every time it reaches (and I step into) the iState:=15 line (at the end of the iState:=0 block). So every scan cycle it goes through the block for iState=0 and jumps out at the same spot. I'm a little new to PLC programming so I may be misunderstanding the flow, but shouldn't this case structure keep moving down in the same scan? If it only handles one case per scan, why doesn't the value of iState persist? Thanks! Update: I restarted the Codesys control today and I was then able to see an error for como1.eError of "WRONG_PARAMETER". I tried doing some digging and another post made me think I should add another line to CODESYSControl_User.cfg, so I now have: [SysCom] Linux.Devicefile=/dev/ttyACM portnum := COM.SysCom.SYS_COMPORT1 So now when I set .udiPort to 1, I get "NO_ERROR" but I also don't read anything from the port (i.e. szRead = 0 always). If I try setting the port to 0 (which I'm confused about, because I added a COMPORT1 line but the device shows on the Pi as ACM0), I get the "WRONG_PARAMETER" error again. Is there an easier way to troubleshoot the Pi and view what ports the Codesys runtime is actually able to see while the Pi is running?
Last updated: 2024-06-06

Post by nikgind on Codesys Communication Manger - Required information model version exists in the model repository but is not found ^{CODESYS Forge talk (Post)}
Hi I am trying to import a custom information model that I created using UA Modeler. I have only added two new methods and two new object types. It is possible to add the information model to the Communication Manager and the two new object types are shown in the Information Model tab. After compiling i get the following error: Communication Manager [Device: PLC Logic: Application]: The information model http://opcfoundation.org/UA/ is required by http://yourorganisation.org/Bsp_3.1/ with a minimal publication date from 15.12.2023 but the device has only a model from 15.09.2021 installed. Probably the information model from 15.09.2021 is missing in the information model repository. The error message does not make sense to me. Should it not be “Probably the information model from 15/12/2023 is missing in the information model repository”? Anyway I have installed the information model from 15/12/2023 but not from 15/09/2021. Which makes the error message even stranger.
Last updated: 2024-06-09

Post by caprez95 on Deleting the trend recording history ^{CODESYS Forge talk (Post)}
Hallo Ich möchte eine laufende Trendaufzeichnung stoppen, den Inhalt löschen und Trend-Diagramm auf 0 zurücksetzen. Laut Codesys soll das mit dem folgenden Code möglich sein: You can insert an input element in the visualization which the operator can use to delete the previous value recording in the trend visualization at runtime. The curve displayed until then is removed and the display starts over. In the application (example: in the program PLC_PRG), implement the following code: itfTrendRecording : ITrendRecording; itfTrendStorageWriter : ITrendStorageWriter; itfTrendStorageWriter3 : ITrendStorageWriter3; sTrendRecordingName : STRING := 'TrendRecording'; itfTrendRecording := GlobalInstances.g_TrendRecordingManager.FindTrendRecording(ADR(sTrendRecordingName)); xClearHistoryTrend: BOOL; IF xClearHistoryTrend THEN itfTrendRecording := GlobalInstances.g_TrendRecordingManager.FindTrendRecording(ADR(sTrendRecordingName)); IF itfTrendRecording <> 0 THEN itfTrendStorageWriter := itfTrendRecording.GetTrendStorageWriter(); IF __QUERYINTERFACE(itfTrendStorageWriter, itfTrendStorageWriter3) THEN itfTrendStorageWriter3.ClearHistory(); END_IF END_IF In the visualization of the trend recording, add a button for deleting the previous curve. Configure its Toggle property with the variable PLC_PRG.xClearHistoryTrend. ⇒ When xClearHistoryTrend is set to TRUE, the previously recorded curve is deleted. The recording immediately starts again. Dies löscht auch die Daten vom Trend, aber das Diagramm wird nicht auf 0 zurückgesetzt, sondern läuft einfach da weiter wo man gestoppt hat. Braucht es für den Diagramm-Reset noch einen zusätzlichen Befehl? Gruss
Last updated: 2024-06-11

Post by hppatrick on Datenkonvertierung für ein SPS-AO-Modul ^{CODESYS Forge talk (Post)}
Hi Leute , ich bin neu hier im Forum und habe seit kurzer Zeit mein eigenes SPS-Projekt. Ich stoße hin und wieder an Probleme aber habe diese auf kurz oder lang gelöst. Nun zu meinem Problem: Als Projekt habe ich eine Kühlwassersteuerung , die einen Relativdruck einließst, und anhand desssen Werte dann einen Frequenzumrichter ansteuert. Z. Bsp. 5Bar -> FU auf 70Prozent. Ich lese in Codesys den Analogwert mit der Wago A20_750_455_020 ein. Dieser Wert wird umgerechnet mit LIN_TRAFO in 0-10 (Bar)und und wird dann über einen PID Regler geregelt. (Bibliothek UTIL). Dieser Wert wird dann wieder für die Ausgangskarte Umgerechnet (LIN_TRAFO) . Nun zu meinem Problem : Die Ausgangskarte nimmt nur einen Word Datentyp und meine Bausteine haben den REAL Datentyp. Wenn ich einen Konvertierungsbaustein nehme, Schmeist mir Codesys einen Fehler und das Programm wird geschlossen. Könnt Ihr mir helfen? Vielen Dank im Voraus (Datei habe ich angehängt). Die Ausgangskarte ist eine Wago 750-555-08
Last updated: 2024-06-14

Post by mp9876 on Problem using MeasureFrequence FB ^{CODESYS Forge talk (Post)}
Hi everyone, new at Codesys and PLC programming in general. I am using Codesys Win V3.5 SP20 I would like to measure an encoder's frequency output (obtaining that pulse train from Factory IO) and intended to use the MeasureFrequence FB (Intern/CAA/Utilities/CAA Mathematics/3.5.19.0). As mentioned in the title what I need to measure is low frequency, such as lower than 40hz (a cycle every 25mS) or so; I could even go lower frequency if required as this is for test purposes) therefore I am not expecting problem measuring a low frequency with that FB The library in question appears to be installed as I can retrieve it from the Library Repository. I can also see it from the Device's Library Manager. Problem arises when I am trying to instantiate this particular FB. I go like this: VAR MeasF:MeasureFrequence; END_VAR Please note that as soon as I start typing the "MeasureFrequence", the MeasureFrequence comes out as a viable option in auto-typing; seems to indicate that the FB is recognized somehow. But there is no way I can compile this as it comes back with the following: C0046: Identifier 'MeasureFrequence' not defined. Tried to rename that to ABC instead of MeasF; same issue. Possibly that the library is not properly installed ? Placeholder ? I would greatly appreciate a bit of guidance if possible. Thank you and regards, Mike
Last updated: 2024-06-24

Post by joachimk on Profinet Controller IP-Adresse ändern ^{CODESYS Forge talk (Post)}
Die IP-Adresse des Profinet-Controllers soll zur Laufzeit geändert werden. Dabei handelt es sich um eine Anwendung auf einem PC mit einer Standard-Ethernetschittstelle (ControlWinV3+WinPcap). Die Datei "CODESYSControl.cfg" wurde dazu angepasst: .... Adapter.0.Name="Ethernet 4" Adapter.0.EnableSetIpAndMask=1 Die konfigurierte IP-Adresse wird zur Laufzeit an die tatsächliche IP-Adresse der Netzwerkschnittstelle mit dem folgenden Befehl angepasst (die Änderung von 192.168.2.33 auf 192.168.2.34 funktioniert auch): Ethernet.UpdateConfiguredIPSettings(IpAddress:=Ethernet.IPAddress, subnetmask:=Ethernet.Subnetmask, gateway:=Ethernet.GatewayAddress); Der Profinet-Controller geht danach auf Störung und gibt die folgende Fehlermeldung aus: "Controller-Status: currently active IP does not match the controller's configuration" Unter "Ethernet diagnostic information" kann man die geänderte IP-Adresse von 192.168.2.34. Ethernet läuft auch ohne Fehler. Unter "PROFINET IO Driver diagnostic information" -> "IPParameter" sieht man noch die alte (konfigurierte) IP-Adresse 192.168.2.33. Wie kann man die Störung beseitigen? Leider habe ich keine Methode zum Ändern der IP-Adresse auf dem Profinet-Controller gefunden? Reconfiguration des Profinet-Controllers?
Last updated: 2024-06-27

Post by gatto on Backtick identifiers ^{CODESYS Forge talk (Post)}
Hello, I’m in Codesys 3.5.20.40 and I try to declare the variable ´var1´ but I get an error. here : https://content.helpme-codesys.com/en/CODESYS%20Development%20System/_cds_rules.html i read : Backtick identifiers By using backticks, characters can also be used in identifiers that are not normally permitted in identifiers, such as special characters. The acute accent character is used for backticks: ´ (Unicode: U+02CA) The use of backticks is recommended in order to be able to use the same identifiers in CODESYS as in other programming languages or documents, such as circuit diagrams. Any character may be used between two backticks, except line breaks and other backticks. Keywords are also allowed as identifiers between backticks. Examples: ´Variable+9´ ´INT´ The backticks are part of each identifier and therefore var1 and ´var1´ are two different identifiers. Example PROGRAM PLC_PRG VAR var1 : INT; ´var1´: INT; END_VAR var1 := var1 + 1; ´var1´ := 12; Are there any limitations or is something missing in my development environment?
Last updated: 2025-10-28

Post by farren on How to stay in a method until something is finished. ^{CODESYS Forge talk (Post)}
I know I'm thinking about this wrong -- too many decades of procedural and event-driven programming and only a few months of PLC ST programming...... I've created a visualization with a button that when pushed calls a method. I want the method to take a pressure reading, wait one minute and then take another pressure reading. I'm looking for leaks. I'm using TON for the delay. It seems like what is happening is that the method gets called once and it takes the first reading and starts the TON. But then execution continues, leaves that method call, and the second reading never happens. I can force the method to keep running until the whole thing is done with a While loop, but I understand that is considered BAD in PLC programming. If it push the button again to call the method again, it picks up where it left off and if the timer is complete then it runs the remaining code. How do I keep that method running until it is complete with just one call without using a while loop that ties up the PLC for a minute? Thanks! -Farren
Last updated: 2025-10-31

Post by aris on Modbus write via FB failure ^{CODESYS Forge talk (Post)}
Hi all, I am using CoDeSys V3.5 and a soft controller Win V3x64. I am trying to read a modbus slave via Function Blocks and not via the channels of the hardware tree for the Slave. I created some requests of type ModbusRequest and I notice that I can read Input Registers and Coils but I can not write Holding Registers and Coils. I am using the library IoDrvModbusTCP 4.1.0.0. When i just use a single modbus request with FC06 (or FC16), there is no request sent to the slave and although the xExecute takes its true value from a pulse of 2 seconds duration, I take almost every 3 minutes an error "TCP_COMMUNICATION_ERROR - 16#A5 - TCP Port. error. Request was not sent". My code is ok because if i change the function code for reading registers, everything works fine. Did anyone have this issue in the past? Thank you in advance.
Last updated: 2025-11-06

Post by jonasz on Deploy LicenseServer for Linux SL ^{CODESYS Forge talk (Post)}
So here's how: I manually installed the following packages: codemeter-lite_8.30.6885.501_amd64.deb codesyslicenseserver_licenseserver_4.18.0.0_all.deb codesyswbmbase_wbmbase_4.18.0.0_all.deb codesyswbmlicensing_wbmlicensing_4.18.0.0_all.deb Of course, the license server appeared immediately. Trying to install it again using Install in the Deploy tab, the same error appears. Of course, the information that such a server is already installed is also there. Configuring PLC, S_PLC, EDGE, and SAFE_TIMER_PROVIDER went smoothly, and basically everything works. I wrote a simple program for S_PLC. I'm loading the programs into PLC and S_PLC. When loading the program into S_PLC, a message appears stating that there is no connection to the S_PLC controller. Timeout error. Restart the controller, attempt to load, and see the above. After changing the cycle time for S_PLC to 50ms, the problem no longer occurs. My question, besides the difficulty of installation for a new user, is what causes the cycle time for S_PLC to be so long, and how can I fix it?
Last updated: 2025-11-14

Post by valenting on License problem with Raspberry Pi ^{CODESYS Forge talk (Post)}
Hello, I have a raspberry pi with a license installed, but Codesys stops after 2 hours, and when I start it manually I have the following message: pszInfo=!!!! no runtime license - running in demo mode(~2 hours) I tried using License Manager, and got the following message: Licensing info not available. There is no dongle attached to the device. I have this message frequently, and usually removing the content of /var/opt/codesys/.cmact_license makes it work. After doing it and restarting Codesys, I have an empty Softcontainer without my License. I tried using "Install license" using the .WibuCmRau file for the corresponding license and got the following message: Licensing info not available. The device does not support this service. I also tried using Additional Functions > Restore Licenses with the Ticket ID and got the following message: This device does not support automatic license backup. How can I reinstall the license to this Raspberry Pi?
Last updated: 2025-11-28

Post by jonasz on Deploy LicenseServer for Linux SL ^{CODESYS Forge talk (Post)}
Good morning, I'm digging into this topic because I'm curious about resolving my problem in a test environment. In my previous message, I asked about the CODESYS Safe Timeprovider SL package (4.18.0.0), which I saw in the illustration. I noticed that it runs as a service. I am asking about this because from the perspective of an "ordinary" user, this service provides easier access to the settings of the time provider's operating parameters. The basic time provider configuration is outlined at https://content.helpme-codesys.com/en/CODESYS%20Control/_rtsl_virtual_safe_time_provider.html. Why my questions? They stem from my specific case, which is experiencing timeout issues. I know that my environment is currently only a test environment. I'm assuming a real-world scenario in which I won't be able to achieve a better result with my configuration, and I will ultimately need to increase the time provider's cycle time. By running the time provider service, I can easily influence the time provider's operation and thus eliminate the problem. I know, I know, safety systems are not life-enhancing extras.
Last updated: 2025-11-19

Post by mrtt on Nach Neuinstallation Plug-In Fehler ^{CODESYS Forge talk (Post)}
https://forge.codesys.com/forge/talk/Engineering/thread/3d0a6d3317/ Hallo, ich wollte mich etwas in Codesys einarbeiten für zukünftige Projekte. Aber ich scheitere schon an der Installation auf zwei PCs (Win10 / Win11). Problem wie im oberen Link, an beiden PCs, aber unterschiedliche Plug-Ins. Laut Installer sind die Pakete aber Installiert, wenn ich sie Deinstalliere kommen andere Meldungen :D... 3.5 19 habe ich auf Win 10 irgendwann immerhin mal zum Starten bekommen. Wenn ich dann an die Pakete mit den Paketmanager gehe, bekomme ich aber während der Installation auch immer die Fehlermeldung. Was kann da los sein? Ich versuche heute noch einen 3. PC, aber irgendwie ist das ja nicht die Lösung :(. Vor allem das es immer andere Plugins sind zwischen 3.5 19/21 und Win10/11. Also da ist irgendwie keine Richtung drin :(. Kann mir aber nicht vorstellen das dass die Regel ist, sondern ich vermute das ich da was falsch mache. Oder eine andere Abhängigkeit / Installation etwas zerschießt... Grüße Malte edit: auf einem frischen Win11 gehts, was ist mi Codesys da nicht in ordnung? edit2: Ok ich habe alles was mit C++ und Runtime war vorher Deinstalliert. Nach der Installation musste ich aber immer noch Plug-Ins korrigieren. Dann ist Codesys gestartet aber eingefroren. Geholfen hat dann noch das deinstalliere von CodeMaster.
Last updated: 2025-11-27

Post by blitz on Can't get SMC_SmoothPath to work ^{CODESYS Forge talk (Post)}
This code works well: PROGRAM PLC_PRG VAR execute : BOOL; abort : BOOL; doMDI : BOOL; manualDataInput : STRING(1024) := 'N5 G01 X0.00 Y200.00 N6 G01 X200.00 Y200.00 N7 G01 X200.00 Y0.00 N8 G01 X0.00 Y0.00'; stringStreamArray: ARRAY[0..NUMBER_OF_CHAINS-1] OF SMC_StringStream2 ; i : UDINT; readNCFromStream : SMC_ReadNCFromStream; sentencesFromStringSteam : SMC_GSentenceQueue ; interpreter : SMC_NCInterpreter; interpreterGeoInfoBuffer: ARRAY[1..GEO_INFO_BUFFERS_SIZE] OF SMC_GeoInfo; roundPath : SMC_RoundPath; roundPathGeoInfoBuffer: ARRAY[1..GEO_INFO_BUFFERS_SIZE] OF SMC_GeoInfo; END_VAR VAR CONSTANT MDI_FILE_NAME : STRING := 'MDI.nc'; NUMBER_OF_CHAINS : UDINT := 15; GEO_INFO_BUFFERS_SIZE : DINT := 500; END_VAR readNCFromStream.bExecute := interpreter.bExecute := roundPath.bExecute := execute; readNCFromStream.bAbort := interpreter.bAbort := roundPath.bAbort := abort; IF doMDI THEN stringStreamArray[0].Init(MDI_FILE_NAME); stringStreamArray[0].AppendData(manualDataInput); stringStreamArray[0].SetEndOfData(); i := 0 ; WHILE i < NUMBER_OF_CHAINS DO readNCFromStream.aStream[i] := stringStreamArray[i]; i := i + 1 ; END_WHILE readNCFromStream.bExecute := TRUE; IF readNCFromStream.bBusy THEN ; END_IF END_IF readNCFromStream( fDefaultVel := 10, fDefaultAccel := 10, fDefaultDecel := 10, fDefaultVelFF := 10, fDefaultAccelFF := 10, fDefaultDecelFF := 10, sentences := sentencesFromStringSteam ); interpreter( sentences:= sentencesFromStringSteam, nSizeOutQueue:= SIZEOF(interpreterGeoInfoBuffer), pbyBufferOutQueue:= ADR(interpreterGeoInfoBuffer)); roundPath( poqDataIn := interpreter.poqDataOut, dRadius := , dAngleTol := , nSizeOutQueue := SIZEOF(roundPathGeoInfoBuffer), pbyBufferOutQueue := ADR(roundPathGeoInfoBuffer));
Last updated: 2026-01-09

Post by fredashbolt on Dynamically Update JSON Payload ^{CODESYS Forge talk (Post)}
I am trying to generate a JSON payload populated with a value that updates for use with a telemetry system, the payload is to be published by MQTT. I have established the MQTT client and can publish a working JSON payload but I can't get the payload to update as the value (iValue) changes. I am using a timer to trigger the .SetValue function periodically, but the JSON will only give the value as it is when it is first initialized using xFirst IF statement. Any suggestions? Thanks VAR pJsonData : POINTER TO JSON.JSONData := factory.Create(); fb_JBuilder : JSON.JSONBuilder; diRootIndex, diObject1Index : DINT; iValue : INT := 10 ; jsonArrayWriter : JSON.JSONByteArrayWriter; wsJsonData : WSTRING(1000); xFirst : BOOL := TRUE; utf8JsonData : STRING(2000); diTempVal : DINT ; PublishTimer : TON ; END_VAR IF xFirst = TRUE THEN fb_JBuilder ( pJsonData := pJsonData , diRootObj => diRootIndex ) ; diObject1Index := fb_Jbuilder.SetKeyWithObject ( "Device" , diParentIndex := diRootIndex ) ; diTempVal := fb_Jbuilder.SetKeyWithValue ( "Temp" , iValue , diParentIndex := diObject1Index ) ; xFirst := FALSE ; END_IF PublishTimer ( IN := PublishTimer.Q = 0 , PT := T#5S ) ; IF PublishTimer.Q THEN fb_JBuilder.SetValue ( iValue , diTempVal ) ; END_IF jsonArrayWriter( xExecute := PublishTimer.Q , pwData := ADR(wsJsonData), udiSize := SIZEOF(wsJsonData), jsonData := pJsonData^, xAsyncMode := FALSE ) ; JSON.Stu.ConvertUTF16toUTF8( ADR ( wsJsonData ) , ADR ( utf8JsonData ) , SIZEOF ( utf8JsonData ) , bStrictConversion := TRUE ) ;
Last updated: 2026-03-10

Post by mjam04 on AM243 LaunchPad as PROFINET Device with CODESYS – RPC Aborted error when scanning devices ^{CODESYS Forge talk (Post)}
Hello, I am currently trying to use the AM243 LaunchPad as a PROFINET device and connect to it using CODESYS. In my setup I am also using a Raspberry Pi running the CODESYS PROFINET Runtime, which acts as the PROFINET controller. The setup of the Profinet controller is correct, so all devices are in the same subnet. However, I encounter an issue when scanning for PROFINET devices in CODESYS. The AM243 LaunchPad appears in the scan results, but the following error is reported: RPC Aborted: 0x16C9A049 Additionally, CODESYS shows the message that the identification data is not available and the IP address should be checked. Because of this error, the controller cannot establish a connection to the device. Another observation is that I cannot ping the AM243 LaunchPad from my PC, even though I configured what should be the correct IP address. Setup: PROFINET Device: AM243 LaunchPad PROFINET Stack: Industrial Communication SDK example PROFINET Controller: Raspberry Pi running CODESYS with PROFINET Runtime Engineering PC: CODESYS IDE Network: Ethernet connection between PC, Raspberry Pi, and AM243 In the attachments there is a screenshot of the corresponding error. Did anybody had the same error? Any hints or debugging suggestions would be greatly appreciated. Thank you!
Last updated: 2026-03-13

Post by ironplc on Ausführen von OPC-UA-Methodenaufrufen auf dem Server durch die SPS als Client ^{CODESYS Forge talk (Post)}
Hallo Zusammen, ich arbeite aktuell an einer Applikation, bei der im OPC-UA-Server eines Geräts ein Methodenaufruf implementiert ist, der für die Ansteuerung des Geräts erforderlich ist. Meine Steuerung agiert in diesem Fall als OPC-UA-Client und kommuniziert mit dem entsprechenden Server. Mit der Software UaExpert oder über eine entsprechende Hochsprache lässt sich der Methodenaufruf problemlos ausführen. Die Umsetzung im IEC-Code in CODESYS ist wohl etwas komplexer, wie ich festgestellt habe. Ich habe aktuell folgende Dinge schon ausprobiert: Symbolkonfiguration Diese entfällt in meinem Fall, da die Symbolkonfiguration nur die Funktionalität für einen OPC-UA Server bereitstellt (Oder?). Da meine Steuerung als Client agiert, kann ich diese Funktion wohl nicht nutzen. Kommunikationsverwalter Diesen kann ich aktuell nur eingeschränkt nutzen, da der Gerätehersteller mit kein Offline-Informationsmodell zur Verfügung stellt / oder stellen möchte. Über das Standardinformationsmodell der OPC-UA-Foundation werden lediglich nur die digitale Signale integriert, jedoch nicht die Methodenaufrufe. CODESYS OPC-UA Client/Server API Hierzu existiert zwar ein Beispielprojekt von CODESYS, jedoch ist die Bibliotheksdokumentation doch sehr knapp gehalten. Für mich ist dies nur relativ schwer zu rekonstruieren. (Aber vielleicht ein Ansatz?) Hat von euch schon jemand Erfahrungen zu dieser Thematik gemacht? Oder ist die Funktionalität im OPC-UA-Stack von CODESYS derzeit noch nicht bzw. nur eingeschränkt implementiert? Hat hier jemand weitere Informationen oder Tipps für mich? Danke schonmal im Voraus!
Last updated: 2026-04-17

Post by kiranbsiddaiah on CodeSys OPC UA client Unable to Connect To OPC UA sever through Username and password ^{CODESYS Forge talk (Post)}
Hi, I'm using codesys v3.5 sp21 software. I have downloaded the sample opc ua client project from https://content.helpme-codesys.com/en/CODESYS%20Examples/_ex_uacapi_example.html and i tested connecting to "prosys opc ua simulation server". Through Anonymous connection it is connecting to server and can read data. Later tried to connect using username and password. First got a SECURITY_CHECKS_FAILED error, trusted the client certificate in the server and this issue resolved. Next got an INVALID_CERTIFICATE error, trusted the server certificate in the client and this issue resolved. After these two error it is not establishing the connection and not giving any error messages. UAAsyncProp: UA.AsyncProperty := (tnTaskName:='UAClientTask', usiTaskPrio:=20, udiTaskInterval:=10000); UAPolicy: UA.SecurityPolicy := (sPolicy:=UA.OpcUa_SecurityPolicy.OpcUa_SecurityPolicy_Aes128Sha256RsaOaep, eSecurity:=UA.SECURITY_MODE.SIGN_AND_ENCRYPT); //UAPolicy: UA.SecurityPolicy := (sPolicy:=UA.OpcUa_SecurityPolicy.OpcUa_SecurityPolicy_None, eSecurity:=UA.SECURITY_MODE.NONE); UAAuth: UA.UserNameAuth := (sUserName:=UAVars.sUser, sPassword:=UAVars.sPass); UAClient: UA.Client := ( itfAsyncProperty:= UAAsyncProp, //sClientName:= 'MyOPC UA client name', //default: ‘CODESYS OPC UA Client’ sURL:= UAVars.sURL, sSession:= UAVars.sSession, itfPolicy:= UAPolicy, itfAuth:=UAAuth, udiTimeout:= 100000 //,itfNamespaceArray:= UAVars.itfNamespaceArray //optional use ); ----------------------------------------------------------------------------------------------------------------------- Please let me know if any additional information required. Thank you...
Last updated: 2026-05-07

Post by chaylak on MC_ReadActualPosition with ST code ^{CODESYS Forge talk (Post)}
hi everyone, i am trying use MC_ReadActualPosition module in ST but i cant do it,( if i use CFC yes i read it) my axis is SoftMotion General Axis Pool->VirtAxisZ [Device: SoftMotion General Axis Pool] codesys V3.5 SP20 program: PROGRAM PLC_PRG VAR VirtAxisZ : AXIS_REF_VIRTUAL_SM3; fbPowerZ : MC_Power; fbReadPos : MC_ReadActualPosition; bEnable : BOOL := TRUE; lrActPos : LREAL; bValid : BOOL; bError : BOOL; fbResetZ : MC_Reset; xZ_Valid : BOOL; xZ_Busy : BOOL; xGlobalPower : BOOL; xGlobalReset : BOOL; xBtnTeachingMode : BOOL; lrGrvZ_OffsetTorque : LREAL := 0.5; lrPulseMmZ : LREAL; rPosFromBlock : LREAL; xZ_IsPowered : BOOL; xZ_PowerError : BOOL; iZ_PowerErrorID : LREAL; rZ_ActualPos : LREAL; lrTargetTorque : LREAL; sZ_ErrorString : STRING; //********** jog fbJogZ : MC_Jog; xJogForward : BOOL; xJogBackward : BOOL; rZ_ActVelocity : REAL; END_VAR fbResetZ( Axis:= VirtAxisZ, Execute:= xGlobalReset); fbPowerZ( Axis:= VirtAxisZ, Enable:= xGlobalPower, bRegulatorOn:= xGlobalPower, bDriveStart:=xGlobalPower , Status=> xZ_IsPowered, Busy=> xZ_Busy, Error=> xZ_PowerError, ErrorID=> iZ_PowerErrorID ); IF xGlobalPower THEN fbJogZ( Axis:= VirtAxisZ, JogForward:= xJogForward, JogBackward:= xJogBackward, Velocity:= 100, Acceleration:= 100, Deceleration:= 100, Jerk:= 1000); END_IF fbReadPos( Axis := VirtAxisZ, Enable := TRUE, Valid => bValid, Position => lrActPos, Error => bError ); IF VirtAxisZ.bError THEN sZ_ErrorString := 'Z Ex err'; ELSIF NOT xZ_IsPowered THEN sZ_ErrorString := 'Z Ex (Power Off)'; ELSE sZ_ErrorString := 'Z Ex Ready'; END_IF IF xBtnTeachingMode THEN lrTargetTorque := lrGrvZ_OffsetTorque; ELSE lrTargetTorque := 0; END_IF VAR_INPUT CFC_Motion: INT; END_VAR
Last updated: 2026-05-15

Post by jroddball79 on PM556-TP-ETH — How to change IP address without overwriting the PLC program? ^{CODESYS Forge talk (Post)}
Hi, I need to change the IP address of an ABB PM556-TP-ETH using ABB Automation Builder. The situation is: I have connectivity to the PLC using the current IP (configured in Communication Settings) Online Login works fine The Network Scan does not detect the PLC IP-Configuration tool shows all fields disabled I don't have the original project source, only an empty project The PLC has no SD card inserted The Online menu does not show an Upload option When I modify the IP in the project and connect, Automation Builder shows: "The PLC configuration needs to be updated. A full PLC download is required" I'm afraid a full download will overwrite the running program. Is there any way to change only the IP address without overwriting the application? I'm also open to solutions using third-party tools, Python scripts, or any other method (DCP protocol, direct TCP communication, etc.) as long as it doesn't overwrite the running application. Thank you
Last updated: 2026-05-19

Post by timvh on JSONByteArrayWriter string result incorrect order ^{CODESYS Forge talk (Post)}
See the example below. You can insert key/value pairs as required At first the JSON string will be filled with: "{$"Key1$": $"Value0$", $"Key2$": [{$"Key3$": 1, $"Key4$": 2}]}" With xAdd, you can insert items, which will result in: "{$"Key1$": $"Value0$", $"Key2$": [{$"Key3$": 1, $"Key4$": 2},{$"Key3$": 3, $"Key4$": 4}]}" VAR factory : JSON.JSONDataFactory; eDataFactoryError : FBF.ERROR; pJsonData : POINTER TO JSON.JSONData := factory.Create(eError => eDataFactoryError); fb_JBuilder : JSON.JSONBuilder; wsValue : WSTRING; diRootIndex, diObjectIndex1, diObjectIndex2, diObjectIndex3 : DINT; iValue : INT; jsonArrayWriter : JSON.JSONByteArrayWriter; wsJsonData : WSTRING(1000); xFirst : BOOL := TRUE; xWrite: BOOL; xAdd: BOOL; END_VAR IF xFirst THEN fb_JBuilder.Reset(); fb_JBuilder(pJsonData := pJsonData, diRootObj => diRootIndex); wsValue := "Value0"; fb_JBuilder.SetKeyWithValue("Key1", wsValue, diParentIndex := diRootIndex); diObjectIndex1 := fb_JBuilder.SetKeyWithArray(wsKey := "Key2", diParentIndex := diRootIndex); diObjectIndex2 := fb_JBuilder.SetObject(diParentIndex := diObjectIndex1); iValue := 1; fb_JBuilder.SetKeyWithValue("Key3", iValue, diParentIndex := diObjectIndex2); iValue := 2; fb_JBuilder.SetKeyWithValue("Key4", iValue, diParentIndex := diObjectIndex2); xFirst := FALSE; xWrite := TRUE; END_IF IF xAdd THEN xAdd := FALSE; diObjectIndex3 := fb_JBuilder.SetObject(diParentIndex := diObjectIndex1); iValue := 3; fb_JBuilder.SetKeyWithValue("Key3", iValue, diParentIndex := diObjectIndex3); iValue := 4; fb_JBuilder.SetKeyWithValue("Key4", iValue, diParentIndex := diObjectIndex3); xWrite := TRUE; END_IF IF xWrite THEN xWrite := FALSE; jsonArrayWriter( xExecute := TRUE, wsLinebreak := "", pwData := ADR(wsJsonData), udiSize := SIZEOF(wsJsonData), jsonData := pJsonData^, xAsyncMode := FALSE ); END_IF IF jsonArrayWriter.xDone OR jsonArrayWriter.xError THEN jsonArrayWriter(xExecute := FALSE, pwData := ADR(wsJsonData), udiSize := SIZEOF(wsJsonData), jsonData := pJsonData^, xAsyncMode := FALSE); END_IF
Last updated: 2026-06-14

Post by wollvieh on Sysfile Konfiguration ^{CODESYS Forge talk (Post)}
...auch noch eine schöne Beschreibung zur Sysfile Konfiguration! Mit Version 3.5.19 wurde die Dateiverwaltung geändert. Siehe folgendes Problem: CDS-81506 – Sicherheitslücke im Dateizugriffssystem des CODESYS Control SysFile-Systems. Es gibt zwei Lösungen: Ändern Sie den Speicherort der Datei (Sie müssen zu /PlcLogic/ wechseln). Wenn Sie die Datei nicht in PlcLogic speichern möchten, fügen Sie die folgende Zeile in der CODESYSControl.cfg unter [SysFile] hinzu: ForceIecFilePath=0 Hier die offizielle Versionsbeschreibung: [[COMPATIBILITY_INFORMATION]] Durch die Aktivierung von ForceIecFilePath ist der Dateizugriff von IEC nun auf die konfigurierten Pfade beschränkt (Dateisandbox)! [SysFile] ForceIecFilePath=1 (neuer Standardwert) Der Standardpfad ist das aktuelle Verzeichnis, der PlcLogic-Unterordner oder ein konfigurierter Pfad. Jeder Dateizugriff außerhalb dieses Pfades wird über PlaceholderFilePath konfiguriert, beispielsweise der Zugriff auf temporäre Dateien oder Wechseldatenträger: [SysFile] PlaceholderFilePath.1=/tmp, $TMP$ PlaceholderFilePath.2=/media/usb, $USB$ PlaceholderFilePath.2.Volatile=1 Weitere Informationen finden Sie in unserem Tutorial „Dateipfade & Platzhalter“. Um das alte Verhalten wiederherzustellen, kann ForceIecFilePath wie folgt konfiguriert werden: [SysFile] ForceIecFilePath=0 Wir empfehlen jedoch dringend, diese Einstellung auf dem neuen Standardwert zu belassen!
Last updated: 2026-01-21

Post by mrkm-dic on CODESYS: Combining Master Redundancy with EtherCAT Ring Topology – Is it Supported? ^{CODESYS Forge talk (Post)}
Hello, I would like to ask whether it is technically supported (and practically achievable) to combine CODESYS Master Redundancy with EtherCAT ring (loop) redundancy in the same system. System setup CODESYS version: CODESYS 3.5.21.40 CODESYS Control SL for Weidmuller u-OS-4.12.2.0 Controllers (Masters): Weidmuller UC20-M4000 ×2, configured as Active / Standby using CODESYS redundancy EtherCAT Slaves: Weidmuller UR20-FBC-EC ×3, supporting EtherCAT ring / line break detection Topology: EtherCAT ring (loop) Main question Is it officially supported to use: ・CODESYS PLC/Master redundancy (Active/Standby) and ・EtherCAT ring topology (for cable redundancy) at the same time? Expected behavior Our expectation is: ・When the Active PLC fails, the Standby PLC becomes Active ・The Standby PLC then takes over the role of EtherCAT Master ・EtherCAT communication is re-established ・I/O control continues after reinitialization (a short interruption is acceptable; no strict bumpless requirement) We do not expect completely seamless / zero-cycle switchover, but we want to understand: ・Whether this combination is supported by design ・Or whether there are known limitations or restrictions when EtherCAT ring mode is used together with Master redundancy Clarification At this stage, the question is mainly about feasibility and support, not about a specific error message yet. Any official guidance, limitations, or real-world experience would be greatly appreciated. Thank you in advance.
Last updated: 2026-02-05

Post by konstantin on Lenze i950 Servo and WAGO PFC200 ^{CODESYS Forge talk (Post)}
Hello, In our workshop we have a Lenze i950 servo drive that has an EtherCAT bus and CiA402 compatibility. The WAGO is PFC200 750-8212 and as per documentation it has built-in license for SoftMotion Light functionality. It is not capable of supporting the full SoftMotion functionality like gearing and synchronizing. I added the EtherCAT esi files from Lenze and the EtherCAT master does see the drive, then I added a SoftMotion Light Axis object. The problem is that I can only energize the axis, I cannot execute any other commands. I set the positive and negative torque limits from the PDOs to 200% and when I try to move the axis by force it does not move back to its original position. I use the SML function blocks from the PLCOpen library and the error from the function blocks is that the op mode cannot be changed. Then I tried using a standard SoftMotion axis object and everything works fine, except the MC_Home function block. The axis moves back to its position when forced out of it. I follow this guide from Lenze - Lenze i950 CODESYS V3 What could cause this issue with the SoftMotion Light axis object? Best Regards Konstantin Kolev
Last updated: 2026-02-11

Sort by relevance or date