Post by installwhat on C0077 on one machine but not another ^{CODESYS Forge talk (Post)}
https://forge.codesys.com/forge/talk/Engineering/thread/92c913bf7c/ Solved by changing the ethercat master version after reading the thread linked above. I think I need to read up on why this happened. I understand that placeholders should point to a particular version for obvious reasons however what has occurred in this instance is different. The example project was released as a "project archive" but it seems to load differently based on what I've got installed in my repositories. I'm going to dig into that tomorrow but any advice is welcome.
Last updated: 2024-06-11

Post by shaun on GAMP 5 and 21 CFR Part 11 ^{CODESYS Forge talk (Post)}
Good day I have been asked to do a project. It is for a pharmaceutical application and data needs to be logged. The spec calls for the control system to comply with GAMP 5 and 21 CFR Part 11. From what I can find online it's got to do with electronic records and validation. Has anyone developed any software using this or are there codesys librarys that can make my life easier in writing this code
Last updated: 2025-10-22

Post by ducng on SMC_FB_WASNT_CALLED_DURING_MOTION when enable MC_MoveRelative ^{CODESYS Forge talk (Post)}
Hello, I am using an Inovance PLC to control a servo via EtherCAT. When I enable MC_POWER, the drive switches to Run mode successfully. After that I call MC_MoveRelative, but I get the error SMC_FB_WASNT_CALLED_DURING_MOTION. The servo vibrates but the motor shaft does not move. I am new to EtherCAT/servo motion control, so I would appreciate any guidance or suggestions for troubleshooting this issue. Thank you in advance for your help.
Last updated: 2025-11-02

Post by imdatatas on SMC_ERROR.SMC_AXIS_NOT_READY_FOR_MOTION when using Drive Virtual ^{CODESYS Forge talk (Post)}
@ducng, Another possible situation could be that normally there are 3 inputs for MC_Power. In your above images, I can't see the "bDriveStart" input activated. As Mr. @gseidel mentioned, you need to make sure MC_Power.Status output should be TRUE. Issuing any movement command without activating the axis would naturally result in an error. For MC_Power; You can set the Enable and bDriveStart inputs to TRUE and try turning the axis activation on and off using only the bRegulatorOn input. Regards, Imdat
Last updated: 2025-11-28

Post by nxbp on About Compatibility ^{CODESYS Forge talk (Post)}
Let's say I have a CODESYS controller (PLC) with a runtime version around 3.5.19. If I use development software version 3.5.21.40 or a later version that will be released in the future for programming, could there be any problems or malfunctions in the controller's program execution or in the execution of the new, updated function blocks from the newer software? I mostly work with servo-based motion applications, so please keep that in mind when answering, and provide a detailed answer so I don't have to email you again about this topic.
Last updated: 2025-12-11

Post by marciohogenelst on stablish CAN communication through the PC's USB port ^{CODESYS Forge talk (Post)}
I'm using Codesys v3.21SP4 on my PC via ControlWin to establish CAN communication through the PC's USB port. The software works fine. The CAN/USB converter works fine and is validated. However, there is no communication. Which folder and file should be modified to allow the CAN/USB converter to work and thus achieve the connection? Converter used: PCAN-View Information not yet processed: Access the folder: C:\Program Files (x86)\3S CODESYS\GatewayPLC\CODESYSControl.cfg Uncomment the line: Component.5=CmpPCANBasicDrv Any help would be appreciated.
Last updated: 2025-12-11

Post by marciohogenelst on stablish CAN communication through the PC's USB port ^{CODESYS Forge talk (Post)}
I'm using Codesys v3.21SP4 on my PC via ControlWin to establish CAN communication through the PC's USB port. The software works fine. The CAN/USB converter works fine and is validated. However, there is no communication. Which folder and file should be modified to allow the CAN/USB converter to work and thus achieve the connection? Converter used: PCAN-View Information not yet processed: Access the folder: C:\Program Files (x86)\3S CODESYS\GatewayPLC\CODESYSControl.cfg Uncomment the line: Component.5=CmpPCANBasicDrv Any help would be appreciated.
Last updated: 2025-12-11

Post by scrollman on Attribute FB for comment ^{CODESYS Forge talk (Post)}
Masters, I need your help. I can explain in different way. I can get the name and comment of parameter if i use "VARINFO", but right now I want to get name and comment of FB from inside one. I can get the name to use the "{attribute 'reflection'}" but I don't understand how to get comment? Do you have any idea how to do it? Thanks
Last updated: 2026-01-08

Post by lmarmonti on Login problem with FileTransfer on Raspberry Pi 5 ^{CODESYS Forge talk (Post)}
Hello everyone, I have the same problem. I have a Linux-based system with CODESYS 3.6.22.20, and I need to download some files from the external web panel. I have enabled: [CmpWebServerHandlerV3] AllowFileTransferServices=1 In this case, I can see the login page when the web panel connects to the device. I can't disable the device user management access because I need to prevent software modifications. Do you have any ideas? Regards,
Last updated: 3 days ago

Post by msirotkin on EtherCAT status errors ^{CODESYS Forge talk (Post)}
Didn't help. I'm just trying to understand why the errors occur. Are they from the poor driver or from the Linux network stack. That's why I wanted to know how the rxerros and lostframes are counted. Because in other places (like ethtool info) there are no any issues. And the Ethercat device works fine. And it also strange that on the second ethernet port with a different HW and driver Ethercat works better, but still time to time gets such errors.
Last updated: 2025-11-26

Post by tobiassantos on History of Alarms ^{CODESYS Forge talk (Post)}
I am running tests using the Windows runtime environment. The alarm history is not being logged and displays the error: "Some kind of disk I/O error occurred. Check disk space" in the alarm table. Furthermore, it is not possible to export the alarms. I have already tried to find a configuration field in Alarm storage and Alarm configuration to fix this problem, but I haven't found any related fields.
Last updated: 2026-01-05

Post by tobiassantos on History of Alarms ^{CODESYS Forge talk (Post)}
I am running tests using the Windows runtime environment. The alarm history is not being logged and displays the error: "Some kind of disk I/O error occurred. Check disk space" in the alarm table. Furthermore, it is not possible to export the alarms. I have already tried to find a configuration field in Alarm storage and Alarm configuration to fix this problem, but I haven't found any related fields.
Last updated: 2026-01-05

Post by sheberle on ERROR: Calling the program "AlarmStorage_Prg" is not allowed from multiple tasks ^{CODESYS Forge talk (Post)}
Do you have any additional information about when the error occurs? I am trying to recreate this issue to find a workaround... Maybe you could also make the project available. You could add the following logfilter to the CODESYS configuration file: [CmpLog] Logger.0.Filter=0xFFFFFFFF Logger.0.Enable=1 Logger.0.MaxEntries=10000 Logger.0.MaxFileSize=1000000 SysSem.Filter=0xFFFFFFFF SysTask.Filter=0xFFFFFFFF I hope that the log filter will show us which task is responsible for this, so we can narrow it down a bit more.
Last updated: 2026-03-31

Post by dgross on Alarm Manager History Message Missing ^{CODESYS Forge talk (Post)}
Hi All, I'm using a webvisu on a control Win V3 SoftPLC. My issue is with the Alarm Managers Alarm history. It does create entry's and does also show the latch data. But it only shows the message of the active alarms. In the history the message is empty (also in the .csv Export file). The archiving in the alarm group is checked and the Alarm storage is activated. I'm using the Version V3.5 SP22 Patch 1. Do you have any idea where that comes from?
Last updated: 2026-04-20

Post by ph0010421 on ModbusTCP_FunctionCode06 ^{CODESYS Forge talk (Post)}
Hi You can add a channel to the standard Modbus TCP library with FC06. From the device tree, add Ethernet device, ModbusTCP master then finally a ModbusTCP slave (your power meter). You can add read/write channels (for any FC) in here. As you add these devices, the necessary libraries will be inserted for you. Alternatively, I have a ModbusTCP client/server library if your RT doesn't have Modbus (I think they all do these days?)
Last updated: 2026-05-18

Post by leag on Reset device password Festo PLC ^{CODESYS Forge talk (Post)}
Hi, I am new to CODESYS, and I want to program a new FESTO, but I am getting this authentication screen. I don't remember the password. I tried with Administrator/Administrator and some other defaults I found online but nothing works. I also tried searching for CODESYSControl_User.cfg and many other recommended directories but I dont seem to have any of them (like CODESYSControlWinV3x64) Could you please help me understand what I need to reset? Thanks a lot
Last updated: 5 days ago

Post by winki on Error in licence activation ^{CODESYS Forge talk (Post)}
Hello, Despite receiving an activation message after entering the license number, I don’t have any license installed on my gateway. I went to check in /var/opt/codesys/ and there is no License file. I searched the entire gateway for a .lic file and found no license. I’m really stuck—how can I fix this, please? When I am using the licence tools I got this picture: But nothing that have been activated. Loic,
Last updated: 2026-02-03

Post by winki on Error in licence activation ^{CODESYS Forge talk (Post)}
Hello, Despite receiving an activation message after entering the license number, I don’t have any license installed on my gateway. I went to check in /var/opt/codesys/ and there is no License file. I searched the entire gateway for a .lic file and found no license. I’m really stuck—how can I fix this, please? When I am using the licence tools I got this picture: But nothing that have been activated. Loic,
Last updated: 2026-02-03

Post by aapostolidis on _NEW when used with classes and interfaces. Interface shows "Hidden Instance" in watch. ^{CODESYS Forge talk (Post)}
Hello, im using dynamic memory allocation with the NEW()-operator. When i instanciate a class with the NEW()-operator and want to debug/watch the interface of the class, the watch is only showing "Hidden Instance" (See attached screenshot). Is there any possibility to debug the interface data ? The interface is working properly but the debugging by the watch is not possible, what is a big disadvantage. Thank you. Best Regards, Alexander
Last updated: 2026-03-24

Post by tommyk-mar on Smooth path is not working with SMC_NCInterpreter ^{CODESYS Forge talk (Post)}
Hello, Im using SMC_NCInterpreter and SMC_NCReadFile2 to read gcode program for CNC machine and what I have observed is that G51 and G52 is not smoothing the path. Machine stops in every point, what could I do to make machine pass through the points without stopping or what could allow me to use smooth path corretly if I use NCInterpreter. Im using it because I want to add variables to my gcode and its not possible directly from the CNC editor thats why I do use external file. Any ideas?
Last updated: 2026-03-26

Post by lofty on CODESYS Download Issue ^{CODESYS Forge talk (Post)}
I am attempting to install CODESYS 3.5.22.20 and the installer gets stuck at "Install Package CODESYS Compatibility Package 3.5.17.20" every single time. I've tried reinstalling the software multiple times and the same issue persists. I've tried running the installer as an administrator and even turned off my virus protection and the same issue persists. I've attached a photo for reference. Has anyone run into this issue before or have any idea what I can do to complete the install?
Last updated: 2026-05-26

Post by gseidel on Problem with keeping up the distance between two axes ^{CODESYS Forge talk (Post)}
Hi alex-n, are there any errors before the crash happens: MC_Phasing.Error, MC_Phasing.CommandAborted, what does the PLC log show before the crash? Does one of the drives show an error? You can achieve the same effect as MC_Phasing by using MC_GearIn and MC_MoveSuperImposed. But probably there is some problem in your application independent of MC_Phasing that can lead to the crash. Best regards, Georg
Last updated: 2026-06-10

Post by fabiodasilveira on Static Analysis Error SA0026 ^{CODESYS Forge talk (Post)}
Hello Everyone, I am really struggling to understand why codesys would present an error regarding the following: VAR strByte1: STRING(10):= '192'; strByte2: STRING(10):= '168'; strByte3: STRING(10):= '1'; strByte4: STRING(10):= '0'; strIPAddress: STRING:= '192.168.1.1'; END_VAR //Updating Variables strByte1:= BYTE_TO_STRING(GVL.abyPSsIpAddress[0]); strByte2:= BYTE_TO_STRING(GVL.abyPSsIpAddress[1]); strByte3:= BYTE_TO_STRING(GVL.abyPSsIpAddress[2]); strByte4:= BYTE_TO_STRING(GVL.abyPSsIpAddress[3]); strIPAddress:= CONCAT(strByte1, CONCAT('.', CONCAT(strByte2, CONCAT('.', CONCAT(strByte3, CONCAT('.', strByte4)))))); Any help would be much appreciated.
Last updated: 2026-07-27

Post by toby on Ethercat Servo Setup ^{CODESYS Forge talk (Post)}
Hi Everyone, I have a simple project with a single servo, but its my first time using Codesys and motion, so I'm a little confused and lost, I've tried to read the tutorial online, but I'm not having much luck sorry. Can I please ask for some pointers. I have a ComfilePi HMI (Raspberry Pi) communicating to a Omron R88D-1SN08H-ECT amplifier. Please see the attached project file (which is better for sharing, the project file, or a archive?). This file was simply for testing the motion of the servo before anything else is tested with it. The project simply rotates the servo 1 rotation when called for, but the speed can vary based on user input. Nothing much fancy. As yet, I haven't had any servo movement, no errors on the amplifier display. How do I link the motion FBs to the physical drive? Thank you very much for any help you can offer. I'm sorry if I'm doing something very stupid or basic and getting it wrong. Have a good day. Toby
Last updated: 2023-09-20

Post by captaincookie on increase default string length in queue ^{CODESYS Forge talk (Post)}
Hello, I'm using Codesys V3.5 SP18 Patch 4. In the ElementCollectionExample Project from Codesys, I test the SimpleQueueExample in a Control Win V3 x64 environment. I try to add a string of 95 characters length to a queue. The default length of strings is defined as 80 characters. In the initialization of a string variable, it is possible to increase the length by the definition of e.g. STRING(1000). But when I write the string defined like this to the queue, only 80 characters are written to it and the rest is missing. I think the default length is still set in the queue definition, so it is necessary to change this, isn't it? Is there any option to increase the default length of strings in the queue? Attached you can find the used project. Thanks in advance. If any information are missing or my description unclear please let me know.
Last updated: 2023-10-05

Sort by relevance or date