Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by simotion on Pointer to Softmotion axis ^{CODESYS Forge talk (Post)}
In my projet I use Softmotion. There are several Softmotion axis (type SM_Drive_Virtual). In the Global Variable List I have an array of pointers to the adress of the Axis. Axis : ARRAY[1..iMaxCntAxes] OF POINTER TO AXIS_REF_SM3 := ADR(AX01_Axis), // [1 ADR(AX02_Axis), // [2] This works, but when compiling I get the message : . [WARNING] E3D: GVL Device: PLC Logic: Application: C0564: A reference to uninitialized variable AX01_Axis is used for initialization of Axis. Accessing the uninitialized variable may result in unexpected behavior. [WARNING] E3D: GVL Device: PLC Logic: Application: C0564: A reference to uninitialized variable AX02_Axis is used for initialization of Axis. Accessing the uninitialized variable may result in unexpected behavior. Is there a way when initializing to force the hardware (softmotion axis) to first initialize and then the Global Variable List?
Last updated: 2023-10-25

Post by bjarne-pagaard on Multiple WebVisu ^{CODESYS Forge talk (Post)}
You can use the switch frame variable, but there should be a variable for each active visu user. You can put the switch frame variable in an array, and use CURRENTCLIENTID as index into the array to get what you want. The CURRENTCLIENTID is assigned to new users automagically by the Visu Management.
Last updated: 2024-03-14

Post by kumareasu on Persistent variable storage ^{CODESYS Forge talk (Post)}
Is there any function function block which can store the persistent variable in HDD/SSD immediatley. My observation is that the persistent variable is getting stored when we shut down or restart the system (Windows+ CoDeSys RTE SL ). the persistent variables are not stored in HDD/SSD, if I power off the system without proper shutdown. Seeking your feedback.
Last updated: 2024-06-12

Post by hemuv on Open Numpad with VU.FbOpenDialogExtended ^{CODESYS Forge talk (Post)}
Hello Barton, I try to log the changes in Numpad (upon Ok button pressed) that an Element name/Element text variable is changed from so to so. How to get the Element name (or text fields Text Variable) from where the Numpad is called? Numpad is Invoked from Inputconfiguration->onMouseDown->Write a variable. Thanks
Last updated: 2024-11-07

Post by mawaloc on IMAGE DISPLAY ACCORDING TO INPUT VARIABLE ^{CODESYS Forge talk (Post)}
Hello thank you to all, it's work regards
Last updated: 2023-08-17

Post by totorovic on Pointer to Softmotion axis ^{CODESYS Forge talk (Post)}
I get the same warning message with initialized variable. Codesys 3.5.19.20
Last updated: 2023-11-09

Post by andreag0 on How to access to variable value through symbolic string name ^{CODESYS Forge talk (Post)}
No
Last updated: 2024-06-13

Post by thysonfury on OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Post)}
Hi after some assistance with an error on a Groov PR2 PLC. We have a few different communications set up as shown below: One Modbus TCP Slave Connection - ( Sending / Receiving Data from a PC ) Two Modbus TCP Master Connection - ( Reading Data from a UPS Panel and Reading Data Gas Chromatograph) One Modbus RTU Slave Connection 485 - (Reading Data from a fire and gas panel) One Modbus RTU Master Connection 485 - (Sending Data to a Telemetry Unit) All Licenses have been installed as per OPTO22 suggestions of the order below: Modbus TCP Master Modbus TCP Slave Modbus RTU Master Modbus RTU Slave When I check on License manager the RTU Master license seems to disappear on installing the RTU. (What ever reason I’ve been told this is “normal”). If I use Device License Read It will successfully read all the licenses correctly. Now the issue is every 2 hours and between 4. For what ever reason the communications seems to end and lock up for about 20 seconds. During this time even if I was logged into the PLC it would kick me off and I’d have to re type the password to enter. Most of the devices can handle this however the RTU flags up a communications failure at the SCADA and is raising alarms every 2 hours and 4 mins. We’ve had multiple people go through the code to check for anything obvious. Does anyone have any ideas?
Last updated: 2024-04-15

Post by thysonfury on OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Post)}
Hi after some assistance with an error on a Groov PR2 PLC. We have a few different communications set up as shown below: One Modbus TCP Slave Connection - ( Sending / Receiving Data from a PC ) Two Modbus TCP Master Connection - ( Reading Data from a UPS Panel and Reading Data Gas Chromatograph) One Modbus RTU Slave Connection 485 - (Reading Data from a fire and gas panel) One Modbus RTU Master Connection 485 - (Sending Data to a Telemetry Unit) All Licenses have been installed as per OPTO22 suggestions of the order below: Modbus TCP Master Modbus TCP Slave Modbus RTU Master Modbus RTU Slave When I check on License manager the RTU Master license seems to disappear on installing the RTU. (What ever reason I’ve been told this is “normal”). If I use Device License Read It will successfully read all the licenses correctly. Now the issue is every 2 hours and between 4. For what ever reason the communications seems to end and lock up for about 20 seconds. During this time even if I was logged into the PLC it would kick me off and I’d have to re type the password to enter. Most of the devices can handle this however the RTU flags up a communications failure at the SCADA and is raising alarms every 2 hours and 4 mins. We’ve had multiple people go through the code to check for anything obvious. Does anyone have any ideas?
Last updated: 2024-04-15

Post by thysonfury on OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Post)}
Hi after some assistance with an error on a Groov PR2 PLC. We have a few different communications set up as shown below: One Modbus TCP Slave Connection - ( Sending / Receiving Data from a PC ) Two Modbus TCP Master Connection - ( Reading Data from a UPS Panel and Reading Data Gas Chromatograph) One Modbus RTU Slave Connection 485 - (Reading Data from a fire and gas panel) One Modbus RTU Master Connection 485 - (Sending Data to a Telemetry Unit) All Licenses have been installed as per OPTO22 suggestions of the order below: Modbus TCP Master Modbus TCP Slave Modbus RTU Master Modbus RTU Slave When I check on License manager the RTU Master license seems to disappear on installing the RTU. (What ever reason I’ve been told this is “normal”). If I use Device License Read It will successfully read all the licenses correctly. Now the issue is every 2 hours and between 4. For what ever reason the communications seems to end and lock up for about 20 seconds. During this time even if I was logged into the PLC it would kick me off and I’d have to re type the password to enter. Most of the devices can handle this however the RTU flags up a communications failure at the SCADA and is raising alarms every 2 hours and 4 mins. We’ve had multiple people go through the code to check for anything obvious. Does anyone have any ideas?
Last updated: 2024-04-15

Post by paulorb on STRUCT AT %MW1000 ^{CODESYS Forge talk (Post)}
Hi I am trying to use STRUCT to parse commands from Modbus/TCP, Modbus client will fill the bytes related to a specific command (type, parameters), then PLC (Codesys) will access the command parameters. A STRUCT will simplify a lot the process of parsing the data, so I don't need to parse byte per byte, address will be mapped to a struct and I can use it for parsing the data. From what I understood, the compiler does not allow me to specify the location of the struct for a %MW register. VAR_COMMAND AT %MW1002: structGenericModbusCommand; This will throw: Bad declaration, use '%ML' for 'structGenericModbusCommand' variable But If I change it to %ML, when you go online you see that it is actually allocating the struct in another memory address. When we go online, on GVL we can see: VAR_COMMAND. structGenericModbusCommand %ML1002 commandType COMMANDTYPE %MB8016 ... %MB8020 I am not specifying a pointer or a reference it is a struct type, why is it mapping to a %MW location (random one). How can I control where it is mapping to? I need a consistent way to map STRUCT to specific modbus address. Is it possible? Thanks, Paulo Note I am using a Codesys OEM: Schneider Machine Expert Logic Builder (M241)
Last updated: 2024-08-13

Post by duvanmoreno24 on Modbus writing on value change ^{CODESYS Forge talk (Post)}
Hi all, I want to know if someone has an idea of how I can write on value change in Modbus Codesys. I have a Wago PLC and I was used to work with E-cockpit which it was quite easy to do that without the necessity to trigger any value when there was a change in the variable ( I will put how easy is ). how you can see just changing the trigger in "On value Change" will do that channel writing automatically when It detects a change in those arrays. On the other hand, in Codesys if I enable the rising edge in Codesys It ask me to put a bool variable and if triggers is going to write that value. That is making me that I have to create a function or a logic to detect the change, the problem I have is that doing that is very tedious. I first approach I got it was to create a Function who returns a bool when the value change, but I tried to keep the old value but what is happening is that in Functions all the data is erased every cycle so I can not keep any Old value. so in the Main program the trigger is going to be TRUE all the time due, the old value is cero every cycle. The second approach I got it was using a function Block (POU_1) and it works but I dont want to instance that function for every Channel or value that I want to check if the value change, Basically if I have 200 values to write trhough modbus I have to create 200 instances of that function which I think it is not practicall at all. It should be a better way to implement this as e-Cockpit from Wago Does. However, I haven't been able to know how.
Last updated: 2024-03-26

Post by jf-fischer on PFC200 als Protokollumsetzer ^{CODESYS Forge talk (Post)}
Hallo, ich möchte IEC 104 Protokolldaten von einem Gerät über Ethernet empfangen, in ein Modbus-TCP Protokoll umwandeln und weiter geben (lesen und schreiben) an andere Modbus Geräte. Dies soll auch in die andere Richtung funktionieren, so dass daten aus dem Modbus Register vom IEC Gerät ausgelesen werden können. die Umwandlung soll eine pfc200 sps von wago durchführen. am Ende sollen die Daten in einer Webansicht visualisiert werden. das Programm der wago möchte ich in codesys 3.5V programmieren. Kann mir jemand helfen, meine Erfahrung mit Codesys ist leider bis jetzt nur sehr grundlegend.
Last updated: 2024-08-07

Post by maralani on Retain memory change to ZERO ^{CODESYS Forge talk (Post)}
Hi, thanks for help, I add some retain variable , then some other variable change to zero , andI was not able to change the value
Last updated: 2023-09-19

Post by simotion on Axis variable indicating modulo of finite setting ^{CODESYS Forge talk (Post)}
What variable of the axis indicates it is a modulo of finite axis? I want to check that in the code, to adopt my motion code between the two types.
Last updated: 2023-11-24

Post by snhatton on Trace commands via Test Manager ^{CODESYS Forge talk (Post)}
One option could be to use a trigger variable to execute your trace and then toggle that variable from a step within a test case.
Last updated: 2023-12-08

Post by arundara on Variable Sync Issue In Soft Plc Redundancy ^{CODESYS Forge talk (Post)}
i understood that we have to use sync variable function. when i used this i was able to achieve on the requirements of our project.
Last updated: 2024-02-13

Post by acc00 on Variable Sync Issue In Soft Plc Redundancy ^{CODESYS Forge talk (Post)}
Hi arundara, I'm also experimenting with Redundandcy. Is the sync variable function the following: "RedundancySynchronizeData()" ? Does the Task time increase a lot when you activate the sync function?
Last updated: 2024-03-11

Post by yannick on Alarm Configuration Notification Action ^{CODESYS Forge talk (Post)}
Hello, I'm trying to configure an alarm variable that changes to True when an error is activated. Unfortunately, the variable is not changing to True. I'm using Codesys V3.5 SP19 Patch7 + Raspi Pi 5. Thanks.
Last updated: 2024-05-13

Post by opineiro on How to manage variable types larger than 64 bits - Ethernet/IP ^{CODESYS Forge talk (Post)}
Thanks, that's what I thought initially. The point is that I can't select a String type variable. See the attached image
Last updated: 2024-09-23

Post by banialuk on CAN Open Manager - varible of SYNC ^{CODESYS Forge talk (Post)}
Hello, were I have find varaible of SYNC "Cycle Period" , or variable that informs about the start of a new cycle SYNC. I want to use this variable in program code. I need to for communication beetween Mster and slave, and send PDO informations.
Last updated: 2024-10-26

Post by banialuk on CAN Open Manager - varible of SYNC ^{CODESYS Forge talk (Post)}
Hello, were I have find varaible of SYNC "Cycle Period" , or variable that informs about the start of a new cycle SYNC. I want to use this variable in program code. I need to for communication beetween Mster and slave, and send PDO informations.
Last updated: 2024-10-26

Trying to pull Logged In user details and certain other variable values and in turn log to a database ^{CODESYS Forge talk (Thread)}
Trying to pull Logged In user details and certain other variable values and in turn log to a database
Last updated: 2024-11-07

Sort by relevance or date