Post by rd76065 on Opto 22 Groov PR2 Modbus TCP Master communication ^{CODESYS Forge talk (Post)}
Previously, I have used ModbusEthernet_04 library for Wago for ModbusTCP Master communicational in Codesys V2.3. How to use same communication of similar UDT for Opto22 Groov PR2 PLC in Codesys V3.5 SP20. Can I use OSCAT library - Network -MB_Client or IODrvModbusTCP - ModbusRequest for this requirement? If any other please guide.
Last updated: 2024-05-31

Post by alessandro on Configuring a CIP object for Explicit Message ^{CODESYS Forge talk (Post)}
We used this with shared memory codesys. and work. OpENer is an EtherNet/IP™ stack for I/O adapter devices; supports multiple I/O and explicit connections. And we adapt this also for Implicit message. But for arrive to the end we spend a lot of time. :-(((
Last updated: 2025-10-24

Post by vtec35 on search runtime 4.9.0.0 for pi 3 ^{CODESYS Forge talk (Post)}
Last updated: 2025-10-24

Post by gseidel on Absolute movement controlled by an external encoder. ^{CODESYS Forge talk (Post)}
Hi polyautomacao, basically, there are two ways to approach this. My first choice would be to check whether your servo drives supports an external encoder, connect the encoder to the servo and configure the servo accordingly. In this case, you would not need to change anything in the CODESYS application. If that is not an option, you could use SM_DrivePosControl, a drive that closes the position loop in the PLC, and feed it with the external encoder positions. See (0). You can switch your servo drive to velocity control mode (SMC_SetControllerMode) and use SMC_FollowVelocity to apply the fSetVelocity of the SM_DrivePosControl to your servo. The MC_MoveAbsolute can then be performed on the SC_DrivePosControl Hope that helps. (0) https://content.helpme-codesys.com/en/CODESYS%20SoftMotion/_sm_example_poscontrol.html Best regards, Georg
Last updated: 2026-03-04

Post by patrik on CODESYS Control for Raspberry Pi SL on Raspberry Pi 4b ^{CODESYS Forge talk (Post)}
Hi! I'm 99% sure I'm running CoDeSys on a raspberry pi 4b. just be aware that there is a separate license for running it on multiple cores. https://store.codesys.com/en/codesys-control-for-raspberry-pi-mc-sl.html
Last updated: 2023-09-05

Post by eschwellinger on RPI Zero w - Edge gateway cant install ^{CODESYS Forge talk (Post)}
ok now it is clear - this is a single core Pi Zero W. For this device there is no edge device available. But just for working with CODESYS it is not really needed and yes plc runs only for 2h unlicensed.
Last updated: 2023-09-13

Post by dekelec on Codesys 2.3 & Peak PCAN ^{CODESYS Forge talk (Post)}
IF you have an USB interface type in "Peak_USB" for CAN card driver (Name of CAN card driver). No need to add libraries for communication via CoDeSys Gateway. For other card types contact PEAK support and they will help you. Regards,
Last updated: 2024-07-08

Post by andreiot40 on Step motor ECT60 Ethercat in codesys 3.5 ^{CODESYS Forge talk (Post)}
Thanks for your response. for Master in log i have : no slaves found, Interface could not be opened, could not open network adapters. Status : Not running FOR ETC60 There is nothing !!!
Last updated: 2024-08-15

Post by andrej on Signing of Boot Application for Raspberry Pi ^{CODESYS Forge talk (Post)}
Hello all, I tried to encrypt the Boot Application (not just to sign it). I got the same Error message as above. Is an additional licencse necessary to sign the boot application for raspberry pi. Thanks for your confirmation. Kind regards Andreas
Last updated: 2025-08-10

Post by pernockham on Control for linux SL, 4.14.0.0 -> 4.15.0.0 breaks web page access. URL requires authentication ^{CODESYS Forge talk (Post)}
After enabling user management, then reverting to "legacy mode" for visu, the web is responding again also for versions later than 4.14.0.0.
Last updated: 2025-09-09

Post by soundbuttonspro on Active vs Unacknowledged Alarm ^{CODESYS Forge talk (Post)}
Meme creators use it to power up their edits. Discord users love it for dropping instant reactions. Streamers lean on it for live sound effects. But what unites them all is the need for instant, sharable meme sounds—and SoundButtonsPro delivers that in the simplest way possible.
Last updated: 2025-09-16

Post by davidbo on Does CODESYS use its own native driver for I2c? ^{CODESYS Forge talk (Post)}
CODESYS Control for Raspberry Pi MC Does CODESYS use its own native driver for I2c? I have a python script communicating with a device simultaneously with a CODESYS doing the same. The bus is not saturated. But I get many read errors
Last updated: 2024-02-13

Post by reinier-geers on Missing Font ^{CODESYS Forge talk (Post)}
Tim. I tried that. After that i used version 19. No problems. After that the Manufacturer whants me to pay for support. I dont pay for there incompetance. So send everythink back. Now looking for a better one.
Last updated: 2024-02-29

Post by john-robinson on Limiting Memory Access of an Array to Within its Bounds ^{CODESYS Forge talk (Post)}
Thanks Tim! This was exactly the functionality we were looking for. We are already using implicit checks to check for divide by 0 errors, we will add implicit checking for array bounds.
Last updated: 2024-03-06

Post by ryusoup on OPC UA Client certificate for datasource link ^{CODESYS Forge talk (Post)}
Hello, I'm looking for a way to set my client certificate, not one which self-signed cert generated with CODESYS, for OPC UA connection via datasource linking. Does anyone know how to archive that? BR,
Last updated: 2024-03-08

Post by alex2 on Codesys SVN ^{CODESYS Forge talk (Post)}
Thank you for your answer. So i assumed correctly... And yes thats pretty expensive... Having to pay that much only for SVN / Git. we will look for that.
Last updated: 2024-04-29

Post by eschwellinger on Ethercat bus on Beckhoff CX with Codesys for Linux ^{CODESYS Forge talk (Post)}
yes I think you need to build the kernel drivers for the CCAT driver for the backplane ETC networkcard https://github.com/Beckhoff/CCAT/
Last updated: 2024-05-13

Post by jonasz on Deploy LicenseServer for Linux SL ^{CODESYS Forge talk (Post)}
Thank you for your response. Is there documentation for the commands? I spent a lot of time trying to figure this out. I have a potato computer at home, so I'll have to test this later.
Last updated: 2025-11-21

Post by pernockham on Unable to deploy "Control for Linux SL 4.18.0.0" ^{CODESYS Forge talk (Post)}
Downloaded and installed edge gateway 4.19.0.0. Unfortunately same behavior: "Control for Linux SL" NOT shown in drop lists on either "Deployment" Tab of tool "Deploy Control SL", or as "installed packages" on "Operation" tab (only "CODESYS Edge Gateway for linux" is shown).
Last updated: 2026-02-16

Post by latassan on RaspberryPi 5 gateway problem ^{CODESYS Forge talk (Post)}
Hello, I'm trying to use a raspberryPi 5 as a PLC. I fixed its IP address, I can ping it. I've also installed the CODESYS Control for Raspberry Pi 64 SL runtime on it. So I've created a gateway (IP address of the Raspberry, TCP port 1217). I see the green dot next to this gateway. When I do a network scan, I can see my raspberry (see photo). When I try to connect to it, I have to define an administrator profile, which I do. On validation, I see a message: No device is responding to the scan request. I've checked that port 1217 is listening on the raspberry, I've uninstalled the runtime then installed it again, but I can't connect. Also, when I try to configure the user groups before connecting, I see that Offline mode is not supported by the device, even though I'm connected to it in the Deploy Control SL tab. When I try to refresh, I see: Gateway not configured properly. How can I connect to my Raspberry? Have I defined my gateway incorrectly?
Last updated: 2025-06-12

Post by dnordenberg on BOOL variable in OPC UA and modbus simultaneously ^{CODESYS Forge talk (Post)}
How can I have an BOOL variable that is read/write in both modbus TCP server and from OPC UA at the same time? Variables with %MX.n %QX.n addressing which is used for BOOL/coils in modbus server is not allowed in OPC UA symbol list on Schneider M251 controllers. I have already asked on Schneiders forum but there are not a lot of codesys experts over there :( So OPC symbols can't have a address and the modbus TCP server needs a address. So how should I do it then? It seems like an impossible combination. Since I want read/write access from both ways I can't just simply make a second variable and assign it the value of another since it would be a one way assignment. I also tried using VAR_CONFIG which then makes the address syntax %Q or %M in my main variable list and that fools OPC UA Symbol Configuration to allow it and then I add the complete %MX.n address of it in the VAR_CONFIG list. This semi works, I can toggle the BOOL from modbus but the OPC UA symbol seems to be read only. It displays symbol status but nothing happens when I toogle it. I think I need another way to have the variables and symbols pointing to the same bits in memory... My plan B is to write a BOOL array compare FB that saves a history bit from previous cycle and if that does not match current status at next cycle for either the OPC symbol or the modbus variable then it copies the new status over to the other. Maybe ugly but it's like my last alternative. Kind regards David
Last updated: 2025-07-14

Post by solidlogicguy on Little endian to Float from Modbus RTU ^{CODESYS Forge talk (Post)}
Hello, I got a device from which I require to read values from I am using a WAGO PLC 750-8212 and I am communicating through Modbus Master FUNCTION BLOCK from library WagoAppPLCModbus in Codesys 3.5 to this device. I already receive data from the device that is a CVM to monitor voltage from a fuel cell. The technical support of the company that makes these devices says that the data is sent in little endian form. And I want to convert it to a float value. The tech support sent me the next instructions of how to do it but I am new using codesys, so any advice or help I will really appreciate so much. Message from tech support: The process is complicated, better to do it with already implemented library in the language/program you use. Basically the process should be next: To convert the two Modbus registers containing parts of a 32-bit float in little-endian byte order to a floating-point number using mathematical operations, you first need to combine the two 16-bit integers (assuming reg1 is the lower word and reg2 is the higher word) and then interpret the result according to the IEEE 754 standard. Given: - Register 192 (reg1) = 4096 - Register 193 (reg2) = 14884 Step 1: Combine the two registers. Since we are dealing with little-endian byte order, reg2 is the high word, and reg1 is the low word: combined = reg2 * 2^16 + reg1 combined = 14884 * 65536 + 4096 combined = 975175680 + 4096 combined = 975179776 Step 2: Convert the combined value to binary: combined_binary = '1110101101011100000000000000000' Step 3: Split the binary into IEEE 754 components: Sign bit (1 bit): 0 Exponent (8 bits): 11101011 Mantissa (23 bits): 01011100000000000000000 Step 4: Convert the binary exponent to decimal and subtract the bias (127 for 32-bit floats): exponent = int('11101011', 2) - 127 exponent = 235 - 127 exponent = 108 Step 5: Calculate the mantissa as a fraction: The mantissa in IEEE 754 format is the fractional part after the leading 1 (which is implicit). Therefore, we need to convert the binary mantissa to decimal and add the implicit leading 1: mantissa_fractional = 1 + int('01011100000000000000000', 2) / 2^23 mantissa_fractional = 1 + 18688 / 8388608 mantissa_fractional = 1 + 0.002227783203125 mantissa_fractional ≈ 1.002227783203125 Step 6: Combine the sign, exponent, and mantissa to get the float value: float_value = (-1)^0 * mantissa_fractional * 2^exponent float_value = 1 * 1.002227783203125 * 2^108 Because the exponent is quite large, the resulting float value is a very large number.
Last updated: 2023-12-15

Post by pernockham on Is there a pragma for init/instantiation of local variables in FB (like in Methods) ^{CODESYS Forge talk (Post)}
Im using a pointer as input for a FB and for convenience I like to use 'referenced' variable internally. I use this setup in methods which works because internal variables are instantiated for each call. In a FB these variables are instantiated and initiated for the first call only. Is there a pragma/attribute available that changes this behaviour to mirror a 'method'-call?
Last updated: 2024-10-31

Post by eschwellinger on Changed Device of Rapberry Pi to MC SL instead of standard SL and cannot connect anymore ^{CODESYS Forge talk (Post)}
1) https://store.codesys.com/en/codesys-control-for-raspberry-pi-sl.html -> SL: Restrictions The combination of Raspberry Pi and a CODESYS Runtime is for private use, test and teaching purposes. Commercial use is not permitted. 2) you could switch between them by /etc/codesyscontrol/CODESYSControl_User.cfg [CmpRasPi] Architecture=armv7l for MC: armv7l for SC: armv6l for 64Bit: aarch64 or in the Deploytool:
Last updated: 2025-08-06

Post by bjarne-pagaard on WebVisu with Runtime Based User Management, Default user (no login) - is it possible? ^{CODESYS Forge talk (Post)}
Hi, With the new Runtime Based User Management, is there any way for WebVisu clients to be logged in to a default user automatically - no login prompt? I would like for the default user to be able to perform normal operation of the machine, without logging in to the WebVisu. This is possible with the Legacy User Management. For the Runtime based user management, there seems to be a default user for the TargetVisu - but not for the WebVisu. -Bjarne
Last updated: 2024-03-14

Sort by relevance or date