Post by svenkaro on Codesyscontrol.service stoppt nach 30s ^{CODESYS Forge talk (Post)}
Wie Du schon vermutet hast, es meint, die Hardware/Firmware sei nicht kompatibel ... ooops... this runtime was built for RASPBERRYPI. Hardware version or firmware version not supported! (-18, 0x00000BB8, 0xFFFFFFFB) Architecture: aarch64 Byte Order: Little Endian CPU(s): 4 On-line CPU(s) list: 0-3 Vendor ID: ARM Model name: Cortex-A72 Model: 3 Thread(s) per core: 1 Core(s) per cluster: 4 Socket(s): - Cluster(s): 1 Stepping: r0p3 CPU(s) scaling MHz: 40% CPU max MHz: 1500.0000 CPU min MHz: 600.0000 BogoMIPS: 108.00 Flags: fp asimd evtstrm crc32 cpuid Caches (sum of all): L1d: 128 KiB (4 instances) L1i: 192 KiB (4 instances) L2: 1 MiB (1 instance) Vulnerabilities: Gather data sampling: Not affected Itlb multihit: Not affected L1tf: Not affected Mds: Not affected Meltdown: Not affected Mmio stale data: Not affected Retbleed: Not affected Spec rstack overflow: Not affected Spec store bypass: Vulnerable Spectre v1: Mitigation; __user pointer sanitization Spectre v2: Vulnerable Srbds: Not affected Tsx async abort: Not affected Allerdings habe ich schon reichlich Firmware versionen getestet.
Last updated: 2024-06-21

Post by richard-wang on Raspberry Pi 4 B HW 1.5 Codesys control 4.10.0 stopps after a few seconds ^{CODESYS Forge talk (Post)}
Hi Preimesbergert I have the same problem and same result as yours, I am wondering if you find any root cause? I would be much appreciated if you can share any finding.
Last updated: 2024-07-29

Post by kaueroratto on Codesys V18 SP18 Patch 4 with G 1.2.1.0 - Error Checkout or Compare ^{CODESYS Forge talk (Post)}
The same occured with me, can anyone support us to understand how to resolve this error?
Last updated: 2024-08-21

Post by esmith on OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Post)}
I think I am having a similar issue. Have you found out what was causing this problem?
Last updated: 2024-09-10

Post by oudom on Missing Button State Variable ^{CODESYS Forge talk (Post)}
My CODESYS 3.5 SP16 Patch 4 in the visualization Button property missing a configuration Button state variable. How do we activate the Button State Variable in the visualization as shown in the attach document?
Last updated: 2024-10-04

Post by jeroenaero on CodeSys Raspberry pi I2C driver not found ^{CODESYS Forge talk (Post)}
We use a Compute module 4 it's 64bit based, so i cannot change it to sl.what are the possibilities to get the i2c working?
Last updated: 2024-11-09

Post by nico01 on Integer with comma in visualization ^{CODESYS Forge talk (Post)}
Hello everyone, I created a visualization with a lot of REAL, with one or two digits after the decimal point. This causes me problems in terms of rounding and memory... is it possible to display an integer with a comma, like with PROFACE or SIEMENS? It's just an "abuse" of display, the comma is just on the visualization. This limits the memory (16 versus 64 bytes) and rounding is easier to manage... See print screen on proface software THANKS
Last updated: 2023-09-20

Post by nz-dave on Bool turning on in case stament in wrong state? ^{CODESYS Forge talk (Post)}
I have a case statement running a process. during one of the steps it has started calling a bool var that is 2 steps further on in the case? i have even tried //commenting it out but it still turns on at the same point in the case. i have also run a trace but cant see anything that would trigger it. Any Ideas? Cheers
Last updated: 2023-12-15

Post by hermsen on Control Runtime Toolkit ^{CODESYS Forge talk (Post)}
Hi, there is a plethora of hardware available for it to be succesful on. In theory every ARM32/64 or x86/64 device is a potential target. Next to this there are embedded device platforms for which specific toolchains are available. A good starting for manufactureres of CODESYS capable devices is available here: https://www.codesys.com/the-system/codesys-inside.html. That should give you a good reference point.
Last updated: 2023-12-31

Post by macros8 on Translation - How to get text as reference in Frames translated? ^{CODESYS Forge talk (Post)}
Hi, one more point. I have been able to create Property of Text which is added to Global text list so it´s fine. But as soon as I use Frame configuration I lose all other properties but some very basics. I need to have still possibility to set Input configuration because my element is Button. Do you know how to make visible all standard properties + my own properties created in Frame configuration? Thanks a lot. M.
Last updated: 2024-01-03

Post by nmcc on Toggling Visualizations using HMI Physical Buttons ^{CODESYS Forge talk (Post)}
Hey thank you for the reply dkugler. I am sorry if this seems like a stupid question. I have the use current visuvariable checkbox enabled. I can see the string names of all my visualizations. I am trying to use ladder logic to be the anser to the button press using "VisuElems.CurrentVisu := 'MainScreen';. This returns an error. Any idea what I am doing wrong or could you point me in the right direction for fixing this. Thanks,
Last updated: 2024-02-13

Post by nmcc on Toggling Visualizations using HMI Physical Buttons ^{CODESYS Forge talk (Post)}
Hey thank you for the reply dkugler. I am sorry if this seems like a stupid question. I have the use current visuvariable checkbox enabled. I can see the string names of all my visualizations. I am trying to use ladder logic to be the anser to the button press using "VisuElems.CurrentVisu := 'MainScreen';. This returns an error. Any idea what I am doing wrong or could you point me in the right direction for fixing this. Thanks,
Last updated: 2024-02-13

Post by installwhat on C0077 on one machine but not another ^{CODESYS Forge talk (Post)}
https://forge.codesys.com/forge/talk/Engineering/thread/92c913bf7c/ Solved by changing the ethercat master version after reading the thread linked above. I think I need to read up on why this happened. I understand that placeholders should point to a particular version for obvious reasons however what has occurred in this instance is different. The example project was released as a "project archive" but it seems to load differently based on what I've got installed in my repositories. I'm going to dig into that tomorrow but any advice is welcome.
Last updated: 2024-06-11

Post by mubeta on Some 'pathetic' errors in SoftMotion program ^{CODESYS Forge talk (Post)}
Yes, this point is part of my misunderstanding. Why, after the execution ot the motion FBs is set to FALSE and exsecuted at lest one time, it must be continuosly called, even if the motion control it's take from another subsequent instruction. This is what I really don't undertand, but what in fact it's happening. For example, in case of stopping a MoveVelocity FB, then Halting the motion by the related FB, the axis at spot goes into error. If there was bad trigger management, the various instructions would NEVER work.
Last updated: 2024-07-18

Post by mrbartpawlowski on OMAC PackML library 1.0.04 ^{CODESYS Forge talk (Post)}
Hello all, Can someone point me to the OMAC PackML State Machine library documentation, I can't find any description of the block functionality ? I was looking into https://content.helpme-codesys.com/en/libs/index.html but there's no PackML there. I'm new to Codesys and don't know if I'm doing something wrong here ? In library tab in codesys whenever I want to see documentation I'm getting an error. Regards Bart
Last updated: 2024-08-15

Post by mrbartpawlowski on OMAC PackML library 1.0.04 ^{CODESYS Forge talk (Post)}
Hello all, Can someone point me to the OMAC PackML State Machine library documentation, I can't find any description of the block functionality ? I was looking into https://content.helpme-codesys.com/en/libs/index.html but there's no PackML there. I'm new to Codesys and don't know if I'm doing something wrong here ? In library tab in codesys whenever I want to see documentation I'm getting an error. Regards Bart
Last updated: 2024-08-15

Post by joep on overruling kinematic limits of [-90°, 90°] in bipod_rotary ^{CODESYS Forge talk (Post)}
Hi All, for my robotics application we are building a 2-axis parallel scara using the kin_bipod_rotary kinematics. Codesys implemented limits of [-90°, 90°] according to the documentation: https://content.helpme-codesys.com/en/libs/SM3_Transformation/Current/SM3_Transformation/Function-Blocks/Positioning-Kinematics/Parallel-Systems/Kin_Bipod_Rotary.html Would it be possible to overrule these limits somehow, our mechanical limits are more in the range of [-110°, 135°] In this range we also don't encounter point where singularity is an issue. Hopeful someone knows a solution, Best regards, Joep
Last updated: 2024-09-04

Post by warrumungi on Opening a Dialog on a specific Client from ST ^{CODESYS Forge talk (Post)}
Hi Thanks, Manuel, for providing this solution and insight. I too had exactly the same problem as you did. While I did implement a custom filter, I'd also like to point out what jinlee mentioned above...I see no reference to VU.PublicVariables.Clients.Current anywhere?? In my case I only needed to show a dialog on a "master" client, not all the clients, so I filtered by IP address to do this.
Last updated: 2024-11-05

Post by riccardo on Codesys SP19 patch 4 ^{CODESYS Forge talk (Post)}
Hallo everyone, I am working on new PLC of Weidmueller that uses Codesys SP19. I made the upgrade at the Patch 4 coming from patch 0. Unce made the upgrade everything is working well in the progect except the web visu user menagent. In the new version, when I perfom the login, I cannot use the keyboard of the device; the window where to digit the user name and password opens, the buttons "OK" and "Cancel" work but the system doesn't allow to put input from the device keybord, the mouse behaves as it is an image. If I active the virtual keypad or numpad it works otherwise nothing. I am wondering if it is a bug of the new package or if I must set something else. Thanks in advance, Riccardo.
Last updated: 2023-11-27

Post by drno on Konfigurierte Compilerversion in Installation nicht verfügbar ^{CODESYS Forge talk (Post)}
Hallo, bedingt durch einen Rechnerwechsel musste ich verschiedene Codesys-Versionen wieder neu installieren, bzw. habe mit dem Codesys-Installer beim Setup einer neuen Version Add-ons einer bestehenden Installation importiert. Nun möchte ich ein bestehendes Projekt, welches auf einem Zielgerät mit recht alter Runtime läuft öffnen, dabei kommt der error "C0510: The configured compilerversion '3.5.8.0' is not available in your installation". Auf dem alten Rechner wurde mit CODESYS V3.5 SP18 Patch 4 eben mit der Compilerversion 3.5.8.0 übersetzt, beim Erstellen des Projektarchives geht jedoch der Compiler nicht mit und so kommt es auf dem neuen Rechner mit der Installation V3.5 SP18 Patch 4 zu diesem error. Übersetze ich das Projekt mit dem aktuellen Compiler, kommt eine ganze Latte an Fehlermeldungen. Gibt es eine Möglichkeit die Compilerversion 3.5.8.0 in die Installation 3.5.18.4 zu bekommen? Danke, schöne Grüße
Last updated: 2023-12-01

Post by preimesbergert on Raspberry Pi 4 B HW 1.5 Codesys control 4.10.0 stopps after a few seconds ^{CODESYS Forge talk (Post)}
Wanted to play a bit with a raspberry Pi 4 Model B HW 1.5 and Codesys. Regardless of the image (tried 32bit / 64bit version from Raspberry Pi Imager) and with all tested Codesys Control versions (4.2.0, 4.8.0, 4.10.0) and regardless if single core / multicore / 64 bit variant, always is the runtime stopped after about 30sec with the nice message: ooops... this runtime was built for RASPBERRYPI. Hardware version or firmware version not supported! (-7, 0x00000BB8, 0xFFFFFFFB) Whats wrong with it?!?!? I read a lot about the issue in topics from 2020-2021 but it always was stated with new Codesys control version issue will be fixed (4.4 for example) but still it is there.
Last updated: 2023-12-21

Post by preimesbergert on Raspberry Pi 4 B HW 1.5 Codesys control 4.10.0 stopps after a few seconds ^{CODESYS Forge talk (Post)}
Wanted to play a bit with a raspberry Pi 4 Model B HW 1.5 and Codesys. Regardless of the image (tried 32bit / 64bit version from Raspberry Pi Imager) and with all tested Codesys Control versions (4.2.0, 4.8.0, 4.10.0) and regardless if single core / multicore / 64 bit variant, always is the runtime stopped after about 30sec with the nice message: ooops... this runtime was built for RASPBERRYPI. Hardware version or firmware version not supported! (-7, 0x00000BB8, 0xFFFFFFFB) Whats wrong with it?!?!? I read a lot about the issue in topics from 2020-2021 but it always was stated with new Codesys control version issue will be fixed (4.4 for example) but still it is there.
Last updated: 2023-12-21

Post by ragarcia on Error while using Codesys SP19 Patch 4 on Windows 11 ^{CODESYS Forge talk (Post)}
Hello everyone, I just installed Codesys SP19 Patch 4 on Windows 11 and every time I open Codesys I get an error that says (Attached image): 'One or more issues ocurred with the current versio profile. Please contact the vendor to resolve these problems. The plug-in {....} (Exactly 4.15.0.0) is required by the current version profile., but has not been installed. It is highly recommended that the tools is terminated. Do you wanto to terminate now?' I cannot install any package since I get this error everytime I open or try to install any package. Can someone help me please, thanks in advanced
Last updated: 2024-03-26

Post by saugat10 on Cannot install Codesys control Multicore in raspberry pi 4 ^{CODESYS Forge talk (Post)}
I have raspberry pi 4 with Raspbian 12 (bookworm). I want to install the latest version of codesys control 4.11.0.0 multicore for 32 bit. I cannot install multicore and it only gives me the option to install Standard. Here are some outputs from the pi pi@saugat:/usr $ uname -a Linux saugat 6.6.20+rpt-rpi-v7l #1 SMP Raspbian 1:6.6.20-1+rpt1 (2024-03-07) armv7l GNU/Linux pi@saugat:~ $ cat /etc/os-release PRETTY_NAME="Raspbian GNU/Linux 12 (bookworm)" NAME="Raspbian GNU/Linux" VERSION_ID="12" VERSION="12 (bookworm)" VERSION_CODENAME=bookworm ID=raspbian ID_LIKE=debian HOME_URL="http://www.raspbian.org/" SUPPORT_URL="http://www.raspbian.org/RaspbianForums" BUG_REPORT_URL="http://www.raspbian.org/RaspbianBugs" A
Last updated: 2024-04-22

Post by paulg on RasPi CAA Serial example - unexpected behavior during debug ^{CODESYS Forge talk (Post)}
I've trimmed down the CAA Serial Codesys example to only listen on one port but, when stepping through the Case structure in debug mode, it jumps out of the structure during a specific point in every scan (I'll point it out below after describing the setup and listing the code). I'm using a Pi 4 Model B, and I have an Arduino Nano Every plugged in via USB which is streaming the following serial message at 1 Hz: Time since opening connection: 1 s Time since opening connection: 2 s ...and so on. The Pi shows the Nano at /dev/ttyACM0 so I edited CODESYSControl_User.cfg to read: Linux.Devicefile=/dev/ttyACM The code in my PLC_PRG is (ignore some of the comments, I hadn't deleted them out from the original example): PROGRAM PLC_PRG VAR xStartTest : BOOL:= TRUE; iState : INT; xTestDone : BOOL;(* True, when the test was done succesfully *) (* Settings to communicate with the COM Port *) aCom1Params : ARRAY [1..7] OF COM.PARAMETER; como1 : COM.Open; comc1 : COM.Close; comw1 : COM.Write; comr1 : COM.Read; //sWrite : STRING := 'Test String!'; sRead : STRING(25); szRead : CAA.SIZE; xCom1OpenError : BOOL; xCom1CloseError : BOOL; xCom1WriteError : BOOL; xCom1ReadError : BOOL; END_VAR //This example shows the communication of two COM Ports with each other. //The first one writes a string of characters, which is read by the second one. //After successful execution, the two COM Ports are closed and the test is done. IF xStartTest THEN CASE iState OF 0: //The parameters are set for the COM Port aCom1Params[1].udiParameterId := COM.CAA_Parameter_Constants.udiPort; aCom1Params[1].udiValue := 1; // the correct Port should be adapted aCom1Params[2].udiParameterId := COM.CAA_Parameter_Constants.udiBaudrate; aCom1Params[2].udiValue := 115200; aCom1Params[3].udiParameterId := COM.CAA_Parameter_Constants.udiParity; aCom1Params[3].udiValue := INT_TO_UDINT(COM.PARITY.NONE); aCom1Params[4].udiParameterId := COM.CAA_Parameter_Constants.udiStopBits; aCom1Params[4].udiValue := INT_TO_UDINT(COM.STOPBIT.ONESTOPBIT); aCom1Params[5].udiParameterId := COM.CAA_Parameter_Constants.udiTimeout; aCom1Params[5].udiValue := 0; aCom1Params[6].udiParameterId := COM.CAA_Parameter_Constants.udiByteSize; aCom1Params[6].udiValue := 8; aCom1Params[7].udiParameterId := COM.CAA_Parameter_Constants.udiBinary; aCom1Params[7].udiValue := 0; //The first Port is opened with the given parameters como1(xExecute := TRUE, usiListLength:=SIZEOF(aCom1Params)/SIZEOF(COM.PARAMETER),pParameterList:= ADR(aCom1Params)); IF como1.xError THEN xCom1OpenError := TRUE; iState := 1000; END_IF //After a successful opening, the next state is reached IF como1.xDone THEN iState := 15; END_IF 15: // the reading process is started comr1(xExecute := TRUE,hCom:= como1.hCom, pBuffer:= ADR(sRead), szBuffer:= SIZEOF(sRead)); IF comr1.xError THEN xCom1ReadError := TRUE; END_IF //After completion the size of the written bytes are saved IF comr1.xDone OR comr1.xError THEN szRead := comr1.szSize; iState := 20; END_IF 20: // If everything was successful the ports are closed and the handles are released comc1(xExecute := TRUE,hCom:= como1.hCom); IF comc1.xError THEN xCom1CloseError := TRUE; END_IF IF comc1.xDone OR comc1.xError THEN iState := 25; END_IF 25: // The first port is closed and the used handle released xTestDone := TRUE; xStartTest := FALSE; iState := 0; como1(xExecute := FALSE); comw1(xExecute := FALSE); comc1(xExecute := FALSE); ELSE iState := 0; END_CASE END_IF I realize as I write this that the .udiPort should be 0 and not 1, but that shouldn't be causing the issue I'm seeing. I'm forcing xStartTest:=TRUE every scan so that I can step into each line and observe what's happening. What I see is that the port parameters are set and the port is opened with no errors, but the code jumps out of the case structure to the last line every time it reaches (and I step into) the iState:=15 line (at the end of the iState:=0 block). So every scan cycle it goes through the block for iState=0 and jumps out at the same spot. I'm a little new to PLC programming so I may be misunderstanding the flow, but shouldn't this case structure keep moving down in the same scan? If it only handles one case per scan, why doesn't the value of iState persist? Thanks! Update: I restarted the Codesys control today and I was then able to see an error for como1.eError of "WRONG_PARAMETER". I tried doing some digging and another post made me think I should add another line to CODESYSControl_User.cfg, so I now have: [SysCom] Linux.Devicefile=/dev/ttyACM portnum := COM.SysCom.SYS_COMPORT1 So now when I set .udiPort to 1, I get "NO_ERROR" but I also don't read anything from the port (i.e. szRead = 0 always). If I try setting the port to 0 (which I'm confused about, because I added a COMPORT1 line but the device shows on the Pi as ACM0), I get the "WRONG_PARAMETER" error again. Is there an easier way to troubleshoot the Pi and view what ports the Codesys runtime is actually able to see while the Pi is running?
Last updated: 2024-06-06

Sort by relevance or date