Post by timvh on Clarifications regarding the appropriate runtime system to use ^{CODESYS Forge talk (Post)}
If you are not using any specific Raspberry Pi functionality, then probably the "universal" Control Linux ARM SL is the approriate runtime to run on the Pi. For the license it doesn't matter which runtime version you choose, because this is not hardware based anymore, but application based. Best is to use the latest version of CODESYS. To determine which license you need, double click on your device, go to the tab License metrics.... Generate the code for your application and see which license you need based on the metrics of your application.
Last updated: 2024-09-24

Post by jacobwago on v3.5 SP19 - Modbus TCP Devices - Channel Limit? ^{CODESYS Forge talk (Post)}
Hello, I have experienced the same issue as described above but for the Modbus Serial configurator. Looking for a solution. In v3.5 SP19 Patch 7 the Modbus Serial Master Slave configurator has a "virtual" limit of 10 channels. In v3.5 SP18 Patch 5 this virtual limit does not exist. I can successfully copy back and forth from 18 to 19 with out any build error. However, this is not a good solution for our customers. What is even more confusing is that the IoDrvModbus library is the same version (4.3.0.0) for both SP18 and SP19. Please help in providing a fix to the virtual channel limit of 10 in SP19. Thanks,
Last updated: 2024-09-29

Post by ivanj on Codesys V3 + Rpi + PCA9685 + two robot arms ^{CODESYS Forge talk (Post)}
greetings to everyone I have a system consisting of rpi3 computer with codesys v3 installed connected to one pca9685 through which the servo motors of the two robotic arms are connected (each robot arm has 6 motors) I managed to get that the pca9685 can only drive 4 servos on the first arm the other 2 on the same robot arm do not respond, nor do the remaining 6 they do not react on the other robotic arm. Power is connected to the pca9685 for motors of sufficient power or amperage. I tried to put another pca9685 but the same thing happens again. What is the possible problem?
Last updated: 2024-10-02

Post by rmaas on TargetVisu for Linux SL not starting ^{CODESYS Forge talk (Post)}
Hello, I am trying to get TargetVisu for Linux working but i am having some troubles. The problem is that after installation it is not starting automatically on boot and i cannot start it from the update Targetvisu tool. When i try i get the following error (see attached screenshot) The file /opt/codesysvisualization/scripts/codesysvisualization_start.sh is missing... Steps performed: - installed fresh Debian 12.7 on virtual machine - installed all required libraries as described here: https://content.helpme-codesys.com/en/CODESYS%20Control/_rtsl_target_visu_for_linux.html - then installed the TargetVisu for Linux SL 4.13.0.0 using the Codesys IDE Does someone know how i can fix this? Best Regards, Rinie
Last updated: 2024-10-02

Post by dsa28 on OPC UA subscriber not operational ^{CODESYS Forge talk (Post)}
Hello All, Hopefully I can get some help configuring an OPC UA subscriber in a CODESYS runtime in a Raspberry Pi 5 that tries to retrieve data from an OPC UA publisher (in this case running in a TwinCAT system). I tried to follow the steps described in the page to implement the OPC UA subscriber: https://content.helpme-codesys.com/en/CODESYS%20Examples/_ex_opcua_pubsub.html Seems that the example provided was created with version 3.5.16.0. Now with version 3.5.20.20 is not possible to open the complete project neither convert it. Anyway, after configuring all IPs and ports used in the OPC UA connection function block but the connection state always shows DISABLED. Can someone help me to do the proper configuration of the OPC UA subscriber? Many thanks in advance.
Last updated: 2024-10-22

Post by niallel on CamBuilder and first boundary position not zero ^{CODESYS Forge talk (Post)}
Hi, I've read the CamBuilder documentation and it shows to use the left boundary of the first segment as SMCB.BoundImplicit(), so that the transition is as smooth as possible. With this it sets X and Y to 0. My first slave position is not 0 (say for example it's 100), so I would set it with SMCB.Bound(0,100). My question is that when the cam goes back to the start (Periodic := TRUE) , will it blend with the last position (360, 100) if I do this? I imagine it will, but the documentation isn't clear as the information in the Periodic Cams only says to set Smooth Transition in the cam properties - but when I'm defining it with code there isn't an option for Smooth Transition to be set. Hope this makes sense? Many thanks,
Last updated: 2024-10-23

Post by shafiq-dsc on Beckhoff EK series cannot detect but BK1120 detect ^{CODESYS Forge talk (Post)}
Dear Support, I have i950 wants to connect with Beckhoff EtherCAT coupler BK1120. There are 2 GSD files for BK1120. 1. BK1120 without MDP.(EtherCAT ESI Device Description (XML)) 2. BK1120 with MDP. (EtherCAT BKxxx (MDP) configuration files) When connecting the BK1120 with i950, scanned devices detects BK1120 without MDP from ESI No1 above. But the KL1408 & KL2408 not detect because they have ELxxxx IO type. When manually insert BK1120 with MDP, the KL1xx8 is able to add manually also but the error shows and Install Missing Descriptions appears. The questions; 1. Why the error occurs? 2. Can the i950 connect with KLxxxx IO type or not? Regards, Shafiq
Last updated: 2024-10-25

Post by dsa28 on OPC UA subscriber not operational ^{CODESYS Forge talk (Post)}
Hi, Thanks for the reply. Please note that the information and links provided are related to OPC UA Client/Server. My problem was related to OPC UA Pub/Sub. In the end I have managed to establish OPC UA Pub/Sub communication between Codesys and TwinCAT systems. Keep in mind that OPC UA Pub/Sub example is not provided in the latest library version 1.1.0.0. The user needs to download the previous version to get the example. During the configuration I ended up with some doubts regarding the usage of IEC_ARRAY type in the dataset definition (see attachment). Can you please give more information on how to use this type? Many thanks.
Last updated: 2024-11-29

Post by askic on Name Validation of Visualization objects ^{CODESYS Forge talk (Post)}
Hello, In my projects, I'm following this recommendation about the rule names in Codesys https://content.helpme-codesys.com/en/CODESYS%20Development%20System/_cds_rules.html, so I always use backtick identifiers, not only for variables, but also for the object names. However, I have noticed that in the current version of Codesys, when adding Visu object, it is not allowed to used these identifiers in the name. This is very different from all other objects like, folder names, POU names, Variable list names etc. I wonder if there is some hidden settings I can use to enable backtick identifiers in the Visu object names? Attached is a screenshot with the details. Thank you!
Last updated: 2025-01-10

Post by pernockham on Slider instance value when accessed through "execute ST-code" ^{CODESYS Forge talk (Post)}
I have a time which I want to modify with a slider. I have confirmed it is possible to set the value of the slider by to_real(time) (I can see that the slider changes according to 'my_time_value's value). Slider variable: to_real(my_time_value); However I fail to access the current slider instance value when I want to write back the value as time (write to a variable will not work as I need a type-conversion before assignment). my_time_value := to_time(slider-instance-value); I tried with this^.? but could not see anything interesting and also THIS^.GEN_Instance.? but nothing resemble what could be the sliders value. Anyone that knows? Thanks!
Last updated: 2025-02-06

Post by pedegani on "Do you really want to perform" dialog boxes ^{CODESYS Forge talk (Post)}
I have the same annoying problem. The confirmation prompt for every single action appeared recently after an update from CODESYS 3.5 SP20 Patch 3 to Patch4, but I don't think it's due to this. Having to confirm every operation while debugging an application is a considerable waste of time and does not help at all to concentrate on development, not to mention that many times you miss the long-awaited event because you are busy looking for the 'yes' button to resume debugging or force a variable. Does anyone know how to disable the confirmation messages?
Last updated: 2025-02-14

Post by darko7417 on When running as a service, CodesysControl doesn't write log files to the disk (and other CmpLog related issuess) ^{CODESYS Forge talk (Post)}
I run CODESYS runtime as a service and use CmpLog (the LogAdd2 function) to log different events to a file. I have done this many times before on various projects and hardware, and it works fine. On this particular system, I have CODESYS 3.5.20.40 running on a Windows 11 PC. The CODESYSControlService autostarts (with Local System credentials, the default), and the application runs fine. However, the configuration file is not read (or at least not the one that should be, or not the CmpLog section), and log files are not written to the disk. I would be thankful if anyone knew why this is happening and how to fix it. A note to CODESYS people: you must provide more information on the codesys configuration file, CODESYSControlService.exe and other major components and system behaviour. You created the service and various features (i.e. logging), but haven't explained how they work, which, in my opinion, is below standard for industrial automation software. These are my observations: - When running as a service, the config file is not read (none of them), or at least the CmpLog section is not read. I checked the log using Codesys IDE, and the CmpLog parameters are not the ones I have set in any of the config files. Which CmpLog config values does the service use, and where does it read them from? I have no idea, but it's not the config files. Here are the codesys config files I located on the PC's disk: o C:\Program Files (x86)\CODESYS 3.5.20.40\GatewayPLC\CODESYSControl.cfg (only 2 lines in this config) o C:\Program Files (x86)\CODESYS 3.5.20.40\GatewayPLC\AppDataFiles\CODESYSControlWinV3\CODESYSControl.cfg o C:\Users\SRV\AppData\Roaming\CODESYS\CODESYSControlWinV3\C4DBB537\CODESYSControl.cfg o C:\Program Files (x86)\CODESYS 3.5.20.40\GatewayPLC\tempCFG\CODESYSControl.cfg - When I run codesys as an app (e.g. by clicking the icon), this config file is read C:\Users\SRV\AppData\Roaming\CODESYS\CODESYSControlWinV3\C4DBB537\CODESYSControl.cfg and log files are written ok. The icon target is "C:\Program Files (x86)\CODESYS 3.5.20.40\GatewayPLC\CODESYSControlService.exe" -d o the -d option, I think, starts a cmd-like window showing service debug output (the output shown in log in the IDE) o the -i option, again I think, means install the service - I tried adding -d to service start parameters in the registry, but it started only once and after that it refused to start. Knowing what -d does and which other options are available would be great (e.g. can I make the service read a different config file). - Syslog UDP logging works fine in any case. - These are my CmpLog parameters ~~~ [CmpLog] Logger.0.Name=PlcLog3 Logger.0.Filter=0xFFFFFFFF Logger.0.Enable=1 Logger.0.MaxEntries=10003 Logger.0.MaxFileSize=50003 Logger.0.MaxFiles=33 Logger.0.Backend.0.ClassId=0x0000010B ;sends logger messages to SysOut Logger.0.Backend.1.ClassId=0x00000104 ;writes logger messages in a file Logger.0.Backend.2.ClassId=0x00000135 ;sends logger messages as UDP syslog Logger.0.Type=0x314 ;Set the timestamp to RTC ~~~
Last updated: 2025-02-27

Post by matthew on High resolution displays with 150% scaling causes CodeSys IDE to be blurry ^{CODESYS Forge talk (Post)}
I have just upgraded my laptop which has a high res display 2560x1600 and I have to have scaling switch on at 150% but everything looks blurry and not crisp, It seems CodeSys IDE is the only software on my system to look this bad, if I switch to 100% it's crisp but way to small. From a bit of research this could be due to the use of old windows forms or something? I have found a temp workaround that sort of works but not great. You have to run CodeSys in compatibility mode and adjust the DPI settings, this works ok and the editor is clear and crisp again but the actual tool bars are small like running at 100% Anyone got any tips for running CodeSys on high res displays with scaling?
Last updated: 2025-03-03

Post by r-c-r on SM3RaspiStepper 0.0.0.6 issue ^{CODESYS Forge talk (Post)}
Hello, I noticed that version 0.0.0.6 is now available, so I tested it using CODESYS V3.5 SP19 Patch 7 and SoftMotion 4.17.0.0. While the project compiles and downloads without issues, I encountered a problem with the 'Enable: GPIO pin number that is set when the axis is enabled (with MC_Power) (0: not used)' functionality — it no longer works (HIGH level not present at the output pin). I observed the same behavior with version 0.0.0.5, whereas version 0.0.0.4 functions correctly. Could you help me identify what might be causing this issue or suggest how to resolve it? Thanks.
Last updated: 2025-03-19

Post by benemenn on OPC UA Method - How to wait for result? ^{CODESYS Forge talk (Post)}
so from what i've learned. Codesys OPCUA Server can only provide OPC UA Methods, when they are created in an XML Model beforehand. So you have to create the XML Model with OPC UA Methods. Then load that model into codesys and create the IEC Blocks. This is automated Code and will create all the variables and Methods from your XML Model. Then they will be displayed on discovery with an OPC UA Client. As far as I understood. There is no way for Methods to be shown in OPC UA when not using an external XML Informationmodel. Codesys can not yet create the informationmodel on itself. Regards
Last updated: 2025-04-02

Post by benemenn on OPC UA Method - How to wait for result? ^{CODESYS Forge talk (Post)}
so from what i've learned. Codesys OPCUA Server can only provide OPC UA Methods, when they are created in an XML Model beforehand. So you have to create the XML Model with OPC UA Methods. Then load that model into codesys and create the IEC Blocks. This is automated Code and will create all the variables and Methods from your XML Model. Then they will be displayed on discovery with an OPC UA Client. As far as I understood. There is no way for Methods to be shown in OPC UA when not using an external XML Informationmodel. Codesys can not yet create the informationmodel on itself. Regards
Last updated: 2025-04-02

Post by alex2 on Error Highlighting Not Working in CODESYS v3.5 SP10 on Windows 11 ^{CODESYS Forge talk (Post)}
Hello everyone, I'm currently using CODESYS v3.5 SP10 on Windows 11, and I've noticed that syntax errors are not automatically underlined in red as they normally should be. Is there a specific setting that needs to be enabled for this feature to work? If so, could you please let me know where to find it? I’ve already tried uninstalling and reinstalling CODESYS, but that didn’t resolve the issue. Also, i have a teammate who have exactly the same computer as me and he didnt encounter any issue. Thank you in advance for your help!
Last updated: 2025-05-13

Post by l-lll on The plug-in is required by the current version profile but has not been installed ^{CODESYS Forge talk (Post)}
Hello everyone, I meet this problem after installing Codesys SP20 Patch 5 on Windows 11 while the dialog box shows that the installation process has been successfully completed. Every time I open Codesys I get an error that says (Attached image): 'One or more issues ocurred with the current version profile. Please contact the vendor to resolve these problems. The plug-in {....} (Exactly x.x.x.x) is required by the current version profile., but has not been installed. It is highly recommended that the tools is terminated. Do you wanto to terminate now?' Can someone help me please, thanks very much！
Last updated: 2025-05-14

Post by l-lll on The plug-in is required by the current version profile but has not been installed ^{CODESYS Forge talk (Post)}
Hello everyone, I meet this problem after installing Codesys SP20 Patch 5 on Windows 11 while the dialog box shows that the installation process has been successfully completed. Every time I open Codesys I get an error that says (Attached image): 'One or more issues ocurred with the current version profile. Please contact the vendor to resolve these problems. The plug-in {....} (Exactly x.x.x.x) is required by the current version profile., but has not been installed. It is highly recommended that the tools is terminated. Do you wanto to terminate now?' Can someone help me please, thanks very much！
Last updated: 2025-05-14

Post by l-lll on The plug-in is required by the current version profile but has not been installed ^{CODESYS Forge talk (Post)}
Hello everyone, I meet this problem after installing Codesys SP20 Patch 5 on Windows 11 while the dialog box shows that the installation process has been successfully completed. Every time I open Codesys I get an error that says (Attached image): 'One or more issues ocurred with the current version profile. Please contact the vendor to resolve these problems. The plug-in {....} (Exactly x.x.x.x) is required by the current version profile., but has not been installed. It is highly recommended that the tools is terminated. Do you wanto to terminate now?' Can someone help me please, thanks very much！
Last updated: 2025-05-14

Post by hclai on Maximum Array Index Issue ^{CODESYS Forge talk (Post)}
I was trying to use a table object in visualization. I want to dynamically show the valid rows in the table. However, it does not work when there is 1 row. i put the maximum array index to 1. it does not show the 1st row. when i change to 2, it show the second row only. my project with older visualization profile version is working perfectly fine. I did some test and realized that i must use a Row Selection variable to change from 0 to 1. With this change of Row selection, then the row 1 will show up.
Last updated: 2025-06-19

Post by manuknecht on Using an Axis of an Axis Group in Torque Conctrol ^{CODESYS Forge talk (Post)}
I don't seem to be able to use an axis, which is part of an Axis Group in torque control mode. I call the SMC_SetControllerMode FB to switch from position to torque control mode, followed by the SMC_SetTorque FB to set the desired torque. This works flawlessly for most axes, however if an axis is part of an axis group, switching the controller mode seems to work without any issues, but the desired torque is never set. SMC_SetTorque does not return an error, but fSetTorque of the axis is never changed. Disabling the axis group before does not change anything, but if I use MC_UngroupAllAxes before changing the controller mode, it all works as it should. Is there no way to control a single axis in torque control, if it is part of an axis group?
Last updated: 2025-07-17

Post by rer-code on Codesys 3.5.18.60 – Application Loss and Persistent Data Corruption ^{CODESYS Forge talk (Post)}
Hi, I’m currently managing over 50 PLCs running Codesys version 3.5.18.60. At seemingly random intervals, some of these devices experience a failure where: All persistent variables are lost. Attempting to log in results in the message: “The application does not exist on device. Do you want to create it and proceed with download?” The log shows: “Loading retain-data/bootproject failed.” From what I’ve gathered, this may be due to a corrupted persistent data file, but I’m not entirely sure how to confirm or resolve this issue. If anyone has encountered something similar or has suggestions for troubleshooting or preventing this, I would greatly appreciate your input. Best regards
Last updated: 2025-08-19

Post by jzhvymetal77 on VarAccGetAddress does not return the correct address for TYPE_ARRAY or TYPE_USERDEF. ^{CODESYS Forge talk (Post)}
VarAccGetAddress does not return the correct address for TYPE_ARRAY or TYPE_USERDEF. When you use VarAccGetNode, it returns a proper IBaseTreeNode if you provide the full path of an array element or structure element, and it even provides the correct data type. The problem is that with TYPE_ARRAY, it returns the start address of the array rather than the indexed element. With TYPE_USERDEF, it only returns the offset of the element instead of the actual address. This causes many issues with nested structures or arrays of structures, since it requires manually calculating the address based on the parent IBaseTreeNode. See attached image and example.
Last updated: 2025-08-28

Post by pernockham on AC Persistence - values are not read from file during start? ^{CODESYS Forge talk (Post)}
I swear I tested this like 20 times yesterday without success. Repeated it today and it works. Maybe the system needed a "real" power reboot? To note. To make a manual edit of a variable I tried some different approaches this is what worked for me. "system/online edited" gvl_var.example_variable REAL:F16#2FFB334H-4 767.7 "manually edited" (with runtime stopped followed by a "cold start" to read from file) gvl_var.example_variable REAL:790.1 (the system will use the manual value but will not set an equivalent "hex" value until next online edit/write cycle)
Last updated: 2025-09-03

Sort by relevance or date