Problem with simulation Modbus ^{CODESYS Forge talk (Thread)}
Problem with simulation Modbus
Last updated: 2024-03-22

Post by ph0010421 on Stepper Drive with Ethercat ^{CODESYS Forge talk (Post)}
Hello That's certainly CiA402. I'll attach a part of the manual for my servos, but the state diagram should be the same at yours. To be sure, get one from your manufacturer. Look at the bits in the StatusWord to see where you are in the diagram, then twiddle the bits in the ControlWord to get you to the next step. Then there are other bits in the StatusWord to tell you 'InPosition' and things like that. From the screenshot, as it mentions only 'PositionProfile' the driver will create the motion profile. So you need to put a target position in here - there should be profile velocity somewhere? Possibly, you need to write these with SDO's? At the minimum, you need to write a value to 0x6081, 0x6083 and 0x6084 (velocity, accel, decel)
Last updated: 2024-03-22

Post by tk096 on High Cycle Times for SoftMotion_PlanningTask when using AxisGroup ^{CODESYS Forge talk (Post)}
Hi, under this circumstances the performance of a Raspberry Pi 4 should be sufficient to run a Softmotion robotics application. A closer look at the project would be required. Maybe you could contact the codesys support? Usually it is recommended to run the planning task cyclically every 2ms with task priority of 0 on a dedicated core. In the task configuration you can have a look at the average and maximum execution time of the planning task. You could use the function block SMC_TuneCPKernel (https://content.helpme-codesys.com/en/libs/SM3_Robotics/Current/SM3_Robotics/POUs/AdministrativeConfiguration/Computation/SMC_TuneCPKernel.html) to define suitable values for the parameters 'fSyncBufferDuration' and 'fPlanningInterval'. However, as previously mentioned, the performance of a Raspberry Pi 4 with realtime patch should be sufficient. The 'fPlanningInterval' parameter specifies the maximum planning step width in seconds. The cycle time of the planning task should not permanently exceed this value. A higher value reduces the computational effort, but can lead to a violation or no full utilization of the set limit values for velocity, acceleration and jerk. From a starting value of 0.016 seconds, the value should be increased gradually until the performance is acceptable. The parameter 'fSyncBufferDuration' specifies the size (in seconds) of the buffer between the planning and fieldbus task. The cycle time of the planning task must not exceed this value at peak times (this will lead to the error SMC_CP_QUEUE_UNDERRUN). A higher value can compensate for peaks in the cycle time of the planning task. At the same time, however, this also increases the latency for executing interrupts and aborting movements.
Last updated: 2024-03-22

Post by ara32 on CODESYS 4 Linux: ^{CODESYS Forge talk (Post)}
Hello! I managed to correctly launch CODESYS Developer Studio 3.5.17, almost all functionality works. The only issue remaining is that when connecting to a device and obtaining its public key, the NCryptEncrypt function is called, which is not fully implemented in the DLL source code, resulting in the connection not being established. Currently, the code of this function in the Wine repository looks like this: SECURITY_STATUS WINAPI NCryptEncrypt(NCRYPT_KEY_HANDLE key, BYTE *input, DWORD insize, void *padding, BYTE *output, DWORD outsize, DWORD *result, DWORD flags) { struct object *key_object = (struct object *)key; TRACE("(%#Ix, %p, %lu, %p, %p, %lu, %p, %#lx)\n", key, input, insize, padding, output, outsize, result, flags); if (flags & ~(NCRYPT_NO_PADDING_FLAG | NCRYPT_PAD_OAEP_FLAG | NCRYPT_PAD_PKCS1_FLAG | NCRYPT_SILENT_FLAG)) { FIXME("Flags %lx not supported\n", flags); return NTE_BAD_FLAGS; } if (flags & NCRYPT_NO_PADDING_FLAG || flags & NCRYPT_PAD_OAEP_FLAG) { FIXME("No padding and oaep padding not supported\n"); return NTE_NOT_SUPPORTED; } if (key_object->type != KEY) return NTE_INVALID_HANDLE; return map_ntstatus(BCryptEncrypt(key_object->key.bcrypt_key, input, insize, padding, NULL, 0, output, outsize, result, flags)); } The program crashes due to the NCRYPT_PAD_OAEP_FLAG flag. I'm not proficient in C++, but I attempted to add handling myself, and here's the result: SECURITY_STATUS WINAPI NCryptEncrypt(NCRYPT_KEY_HANDLE key, BYTE *input, DWORD insize, void *padding, BYTE *output, DWORD outsize, DWORD *result, DWORD flags) { struct object *key_object = (struct object *)key; TRACE("(%#Ix, %p, %lu, %p, %p, %lu, %p, %#lx)\n", key, input, insize, padding, output, outsize, result, flags); if (flags & ~(NCRYPT_NO_PADDING_FLAG | NCRYPT_PAD_OAEP_FLAG | NCRYPT_PAD_PKCS1_FLAG | NCRYPT_SILENT_FLAG)) { FIXME("Flags %lx not supported\n", flags); return NTE_BAD_FLAGS; } if (flags & NCRYPT_NO_PADDING_FLAG) { FIXME("No padding not supported\n"); return NTE_NOT_SUPPORTED; } BCRYPT_OAEP_PADDING_INFO oaepInfo = { 0 }; oaepInfo.pszAlgId = BCRYPT_SHA1_ALGORITHM; NTSTATUS status = BCryptEncrypt(key_object->key.bcrypt_key, input, insize, &oaepInfo, NULL, 0, output, outsize, result, flags); if (key_object->type != KEY) return NTE_INVALID_HANDLE; return map_ntstatus(BCryptEncrypt(key_object->key.bcrypt_key, input, insize, padding, NULL, 0, output, outsize, result, flags)); } Now, when calling the connection, it crashes with the error "bcrypt:BCryptEncrypt flags 0x4 not implemented." Can anyone help with enhancing this functionality or at least point me in the right direction?
Last updated: 2024-03-22

CODESYS 4 Linux: ^{CODESYS Forge talk (Thread)}
CODESYS 4 Linux:
Last updated: 2024-03-22

Post by manuknecht on High Cycle Times for SoftMotion_PlanningTask when using AxisGroup ^{CODESYS Forge talk (Post)}
Hi, thanks a lot for the response. I did check all these parameters, but if the PlanningTask takes up to 60 ms, I can't increase the Buffer to such values. I contacted the Codesys support with a projectarchive. Let's see if they can help. Thanks again for your great support!
Last updated: 2024-03-22

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi everybody We are currently working on a project with an RS232 serial COM interface and using the CAA SerialCOM library. We have it working fine reading and writing data, although we have found an issue we cannot resolve and any suggestions would be helpful. We have noticed that after a while the RS232 stops working. We have tracked this down to the HANDLE hCom keeps increasing and when this reaches 1023 the COM returns an unknown error "5003". Is there a way to reset this hCom reference? Thanks Richard
Last updated: 2024-03-22

Post by timvh on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
You should only open de COM port once and then leave it open. This hCom should not keep on incrementing. (off course when you are done communicating, you need to close the COM port)
Last updated: 2024-03-22

Post by phoward131 on Text List Fallback Value ^{CODESYS Forge talk (Post)}
I am relatively new to Codesys and I'm trying to develop an HMI that displays what mode a particular device is in based on an integer value. I am currently using dynamic texts with a text list which works fine but I am looking for a way to display a particular string (ie 'Unknown') when the index doesn't match any of of the indices in the text list. I can enter 'Unknown' in the text property of the text field element which works as expected but it displays the single quotes on the visualization. How can I escape these quotes to simply display the word Unknown? Thanks!
Last updated: 2024-03-22

Post by wollvieh on Raspi Pi Bullseye Webvisu Autostart ^{CODESYS Forge talk (Post)}
Anbei meine Lösung zum Autostart der Webvisu, vllt. hilft es jemandem... =============================== Raspberry Pi Bullseye 11 Autostart Codesys Webvisu im Kiosk Mode 1)Datei erstellen: sudo nano/etc/xdg/autostart/Visustart.desktop 2)Inhalt der Datei: [Desktop Entry] Type=Application Name=Visustart Exec=bash -c "sleep 30 && /home/pi/Desktop/Visu" 3)Visu Datei erstellen sudo nano /home/pi/Desktop/Visu 4) Inhalt der Datei: #!/bin/sh xset -dpms xset s off xset s noblank matchbox-window-manager -use_titlebar no & unclutter & chromium-browser -display=:0 --kiosk --incognito --window-positon=0,0 5) Datei ausführbar machen sudo chmod+x /home/pi/Desktop/Visu ... nach Neustart Raspi startet die Codesys Webvisu automatisch im Kiosk Mode ===============================
Last updated: 2024-03-24

Post by struccc on Release SP20 - Changes in behaviour? ^{CODESYS Forge talk (Post)}
Dear all, I've just started to migrate some of my ancient projects to SP20. There is one strange error (?) I have noticed so far. In a method call, depending on the circumstances I would like to return reference to an object, or an invalid reference: METHOD Add_EVT_OUT : REFERENCE TO FB_MSG VAR END_VAR IF __ISVALIDREF(refMSG_Entry) THEN Add_EVT_OUT REF= MANAGER.AddMsg_EVT_OUT( refMSG_Entry, _Get_EVT_Message(MSG_EVENT.OUT), _Get_EVT_AddCode(MSG_EVENT.OUT) )^; ELSE Add_EVT_OUT := 0; END_IF So far setting a reference variable to 0, did this. But now, the expression Add_EVT_OUT := 0; gives an error: [ERROR] DB_WTP_370: Add_EVT_ACK MSG_TRIGGER_EXT: C0032: Cannot convert type 'BIT' to type 'REFERENCE TO FB_MSG' Naturally... I can write: Add_EVT_OUT := DWORD#0; But is this the correct way? Is there any constant I could use instead, like "NULL"? Or this is totally wrong and to be avoided?
Last updated: 2024-03-24

Post by smartcoco on Release SP20 - Changes in behaviour? ^{CODESYS Forge talk (Post)}
You should use this method: VAR NULL:REFERENCE TO FB_MSG END_VAR Add_EVT_OUT REF= NULL;
Last updated: 2024-03-25

Post by andrax on Raspi Pi Bullseye Webvisu Autostart ^{CODESYS Forge talk (Post)}
Vielen Dank Für das Script.
Last updated: 2024-03-25

Raspi Pi Bullseye Webvisu Autostart ^{CODESYS Forge talk (Thread)}
Raspi Pi Bullseye Webvisu Autostart
Last updated: 2024-03-25

Post by wollvieh on Raspi Pi Bullseye Webvisu Autostart ^{CODESYS Forge talk (Post)}
Anbei meine Lösung zum Autostart der Webvisu, vllt. hilft es jemandem... =============================== Raspberry Pi Bullseye 11 Autostart Codesys Webvisu im Kiosk Mode 1)Datei erstellen: sudo nano/etc/xdg/autostart/Visustart.desktop 2)Inhalt der Datei: [Desktop Entry] Type=Application Name=Visustart Exec=bash -c "sleep 30 && /home/pi/Desktop/Visu" 3)Visu Datei erstellen sudo nano /home/pi/Desktop/Visu 4) Inhalt der Datei: #!/bin/sh xset -dpms xset s off xset s noblank matchbox-window-manager -use_titlebar no & unclutter & chromium-browser -display=:0 --kiosk --incognito --window-positon=0,0 5) Datei ausführbar machen sudo chmod+x /home/pi/Desktop/Visu ... nach Neustart Raspi startet die Codesys Webvisu automatisch im Kiosk Mode ===============================
Last updated: 2024-03-24

Post by fless on Release SP20 - Changes in behaviour? ^{CODESYS Forge talk (Post)}
use this to set an invalid reference Add_EVT_OUT REF= 0;
Last updated: 2024-03-24

Raspi Pi Bullseye Webvisu Autostart ^{CODESYS Forge talk (Thread)}
Raspi Pi Bullseye Webvisu Autostart
Last updated: 2024-03-24

How to catch save button event ^{CODESYS Forge talk (Thread)}
How to catch save button event
Last updated: 2024-03-25

Post by hock714 on How to catch save button event ^{CODESYS Forge talk (Post)}
I want to catch the event whenever save button being click in C#.
Last updated: 2024-03-25

Post by bschraud on Zielsystem stimmt nicht mit dem verbundenen Gerät überein ^{CODESYS Forge talk (Post)}
Dank umfangreicher Hilfe durch den Kontron Support kann ich nun wieder übersetzen. Es waren einige Bibliotheken auf einem älteren, nicht 64bit-kompatiblen Stand. Beim Öffnen des Projektes erscheint zwar ein Dialog zum Aktualisieren der Bibliotheken. Diesen hatte ich auch mit "Auf neueste setzen" bestätigt. Trotzdem waren etliche Bibliotheken im Projekt veraltet. Leider habe ich noch keine Stelle in der Online Hilfe gefunden, die die Zusammenhänge in der Bibliotheksverwaltung und das Vorgehen bei Fehlern erklärt. (Z.B. wie man vermeiden kann, dass eine Komponente automatisch eine ältere Bibliotheksversion lädt, obwohl eine aktuelle Version der gleichen Bibliothek schon hinzugefügt wurde.) Vielen Dank für die Hilfe!
Last updated: 2024-03-25

Zielsystem stimmt nicht mit dem verbundenen Gerät überein ^{CODESYS Forge talk (Thread)}
Zielsystem stimmt nicht mit dem verbundenen Gerät überein
Last updated: 2024-03-25

Post by baradejoo on PubSub communication - example ^{CODESYS Forge talk (Post)}
Hi, Recently, I purchased a license for PubSub communication from the CODESYS store. Unfortunately, after installation, I couldn't find any example code in the files. Is there anyone who can share such an example/send links or help with writing such communication in ST language?"
Last updated: 2024-03-25

PubSub communication - example ^{CODESYS Forge talk (Thread)}
PubSub communication - example
Last updated: 2024-03-25

Post by baradejoo on PubSub communication - example ^{CODESYS Forge talk (Post)}
Hi, Recently, I purchased a license for PubSub communication from the CODESYS store. Unfortunately, after installation, I couldn't find any example code in the files. Is there anyone who can share such an example/send links or help with writing such communication in ST language?"
Last updated: 2024-03-25

PubSub communication - example ^{CODESYS Forge talk (Thread)}
PubSub communication - example
Last updated: 2024-03-25

Sort by relevance or date