Post by wiresplus on How to Connect / Go Online without re-downloading the project ^{CODESYS Forge talk (Post)}
Hello, I have a PLC in a remote location. I can connect to it, but when I use a different PC, it asks me to re-download to the PLC - which will a) interrupt production and b) cause version issues. Codesys being open-source, if someone else has made changes, I need to be able to connect, upload the current project, compare it with mine and then decide what next. Every time I connect, it says Warning: An application 'Application' is currently in RUN mode on the PLC. As there is no matching compile information, this existing application needs to be replaced. Click 'Yes' to download the latest code or 'No' to abort. What am I doing wrong?
Last updated: 2024-04-13

Post by eschwellinger on How to Connect / Go Online without re-downloading the project ^{CODESYS Forge talk (Post)}
Which plc type is it: Either use Automationserver to do this or save the project archives instead of projects or use the source dowload function and reopen the application from plc. So you need to chose one of them.
Last updated: 2024-04-13

How to Connect / Go Online without re-downloading the project ^{CODESYS Forge talk (Thread)}
How to Connect / Go Online without re-downloading the project
Last updated: 2024-04-13

Post by codesysjupiter on Could not be resolved - Library error ^{CODESYS Forge talk (Post)}
I tried. but not work.
Last updated: 2024-04-13

Post by wiresplus on warning message ^{CODESYS Forge talk (Post)}
00 I have the same issue, and no answers on any forums that I can see.
Last updated: 2024-04-13

Post by danwoodlock on Rpi zero w lost license after 4.11 update ^{CODESYS Forge talk (Post)}
Hello all, Encountered an issue with my zero which seems to have happened after the 4.11 update. It now runs in demo mode (2hr) and I am trying to see what the appropriate steps are prior to contacting codesys directly. Background: I recently did a fresh install of w11 on my pc, so it seems "c:\ProgramData\CODESYS\Licenses\" only has information related to my pi5, which I licensed just this past Friday. I have all my license documentation about my rpi zero as far as the emails received, but when I try to claim using the ticket number it says its already been used, or something to that effect, which it was. Currently trying to perform device license reader, which is taking some time.
Last updated: 2024-04-14

Post by marcolim on Slow modbus digital input response ^{CODESYS Forge talk (Post)}
Hi francoinf, I've the similar problem and similar configuration. I did with an Arduino Board loaded by a ModbusRTUServer application on it. What I've notice is the slowly acquisition when release the digital signal (e.g. pin2) when it gets off. Anyone have suggestion?! Thanks
Last updated: 2024-04-13

Post by ademarvribeiro on warning message ^{CODESYS Forge talk (Post)}
this mean your project dont have compile information. try to upload code from PLC and them go online. To know the differences between online program and your project clica in Details, when the message pop-up.
Last updated: 2024-04-14

Post by niallel on Continuous MC_PositionProfile ^{CODESYS Forge talk (Post)}
Looks like it's not possible, so I take it using Cams is the way to do this.
Last updated: 2024-04-13

warning message ^{CODESYS Forge talk (Thread)}
warning message
Last updated: 2024-04-14

Post by thysonfury on OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Post)}
Hi after some assistance with an error on a Groov PR2 PLC. We have a few different communications set up as shown below: One Modbus TCP Slave Connection - ( Sending / Receiving Data from a PC ) Two Modbus TCP Master Connection - ( Reading Data from a UPS Panel and Reading Data Gas Chromatograph) One Modbus RTU Slave Connection 485 - (Reading Data from a fire and gas panel) One Modbus RTU Master Connection 485 - (Sending Data to a Telemetry Unit) All Licenses have been installed as per OPTO22 suggestions of the order below: Modbus TCP Master Modbus TCP Slave Modbus RTU Master Modbus RTU Slave When I check on License manager the RTU Master license seems to disappear on installing the RTU. (What ever reason I’ve been told this is “normal”). If I use Device License Read It will successfully read all the licenses correctly. Now the issue is every 2 hours and between 4. For what ever reason the communications seems to end and lock up for about 20 seconds. During this time even if I was logged into the PLC it would kick me off and I’d have to re type the password to enter. Most of the devices can handle this however the RTU flags up a communications failure at the SCADA and is raising alarms every 2 hours and 4 mins. We’ve had multiple people go through the code to check for anything obvious. Does anyone have any ideas?
Last updated: 2024-04-15

Recipe Manager in PRG (3.05.13.XX) ^{CODESYS Forge talk (Thread)}
Recipe Manager in PRG (3.05.13.XX)
Last updated: 2024-04-15

Post by syjoo on Recipe Manager in PRG (3.05.13.XX) ^{CODESYS Forge talk (Post)}
I'm using version 3.5.13. Is it possible to handle Recipe Manager in PRG in this environment? Can you give me a simple example? Although it has been confirmed that the functions work on Recipe Manager, they do not work properly when implemented through FB within a simple PRG. I would like to save the current value as a recipe or load the recipe's value as the current value. And I want to save the recipe as a file or load the recipe saved as a file. somebody help me. (TT)
Last updated: 2024-04-15

Post by thysonfury on OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Post)}
Hi after some assistance with an error on a Groov PR2 PLC. We have a few different communications set up as shown below: One Modbus TCP Slave Connection - ( Sending / Receiving Data from a PC ) Two Modbus TCP Master Connection - ( Reading Data from a UPS Panel and Reading Data Gas Chromatograph) One Modbus RTU Slave Connection 485 - (Reading Data from a fire and gas panel) One Modbus RTU Master Connection 485 - (Sending Data to a Telemetry Unit) All Licenses have been installed as per OPTO22 suggestions of the order below: Modbus TCP Master Modbus TCP Slave Modbus RTU Master Modbus RTU Slave When I check on License manager the RTU Master license seems to disappear on installing the RTU. (What ever reason I’ve been told this is “normal”). If I use Device License Read It will successfully read all the licenses correctly. Now the issue is every 2 hours and between 4. For what ever reason the communications seems to end and lock up for about 20 seconds. During this time even if I was logged into the PLC it would kick me off and I’d have to re type the password to enter. Most of the devices can handle this however the RTU flags up a communications failure at the SCADA and is raising alarms every 2 hours and 4 mins. We’ve had multiple people go through the code to check for anything obvious. Does anyone have any ideas?
Last updated: 2024-04-15

Post by thysonfury on OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Post)}
Hi after some assistance with an error on a Groov PR2 PLC. We have a few different communications set up as shown below: One Modbus TCP Slave Connection - ( Sending / Receiving Data from a PC ) Two Modbus TCP Master Connection - ( Reading Data from a UPS Panel and Reading Data Gas Chromatograph) One Modbus RTU Slave Connection 485 - (Reading Data from a fire and gas panel) One Modbus RTU Master Connection 485 - (Sending Data to a Telemetry Unit) All Licenses have been installed as per OPTO22 suggestions of the order below: Modbus TCP Master Modbus TCP Slave Modbus RTU Master Modbus RTU Slave When I check on License manager the RTU Master license seems to disappear on installing the RTU. (What ever reason I’ve been told this is “normal”). If I use Device License Read It will successfully read all the licenses correctly. Now the issue is every 2 hours and between 4. For what ever reason the communications seems to end and lock up for about 20 seconds. During this time even if I was logged into the PLC it would kick me off and I’d have to re type the password to enter. Most of the devices can handle this however the RTU flags up a communications failure at the SCADA and is raising alarms every 2 hours and 4 mins. We’ve had multiple people go through the code to check for anything obvious. Does anyone have any ideas?
Last updated: 2024-04-15

Post by huzeyfe on SMC_INT_QPROF_DIVERGES ^{CODESYS Forge talk (Post)}
Last updated: 2024-04-15

OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Thread)}
OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins
Last updated: 2024-04-15

OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Thread)}
OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins
Last updated: 2024-04-15

Post by marcolim on Slow modbus digital input response ^{CODESYS Forge talk (Post)}
[Update]. My issue's solved, I applied the resistors in Pull-down configuration on each digital input. In thus configuration never happened "floating or delaying" acquisition on SoftPLC/Arduino Board.
Last updated: 2024-04-15

Slow modbus digital input response ^{CODESYS Forge talk (Thread)}
Slow modbus digital input response
Last updated: 2024-04-15

Post by mbmik on IoDrvModbusTCP_Diag not defined when using MODBUS ^{CODESYS Forge talk (Post)}
Hi Im trying to setup a Weidmüller WL2000 to run with MODBUS, to get some data from a server. Codesys V3.5 SP20. The issue is, that whenever i attach an ethernet port and add MODBUS Master und also a Slave, codesys will compile the project, but there always seem to be some remaining errors, which or only visible, when setting the messages window to "Pre-Compiled". I tried a lot of stuff to get rid of these errors, but cant find to seem the reason. New installation of codesys, cleaned project, setup completely empty new project, manually adding libs. Nothing helps. Any help is apreciated. Maybe we are doing something wrong.. Example Project is available, if somebodey wants to take a look. Greetings and thanks alot
Last updated: 2024-04-15

Post by salvadegianluca on How to use TON inside an FB that is instanced within a Visu page ^{CODESYS Forge talk (Post)}
Hi everyone; I'm building a project in which the drag of the mouse over some controls (or the click event) changes the background color of the control items; this change of color is made with an FB that assignes a color code to the background with MUX command based on the value of an enumerator, this part is perfectly working but, when I'm using a touchpanel instead of a web visu (controlled by a mouse) I get into some issues as it seems that the touch operations are not triggering the MouseEnter and MouseLeave properties as it's done with the mouse.... For this reason I'm trying to add a TON to my FB and, if the enum that changes color remains at the same state for more then 3s I'm automatically resetting it to it's "0" so the item gets back the not selected color. Anyhow it looks like the TON function from library is not working in these FB that are instanced in the various visualizations, as instead they do if I create some instances within the POUS. Anyone has ideas of how to make them work?
Last updated: 2024-04-15

How to use TON inside an FB that is instanced within a Visu page ^{CODESYS Forge talk (Thread)}
How to use TON inside an FB that is instanced within a Visu page
Last updated: 2024-04-15

Post by salvadegianluca on How to use TON inside an FB that is instanced within a Visu page ^{CODESYS Forge talk (Post)}
Hi everyone; I'm building a project in which the drag of the mouse over some controls (or the click event) changes the background color of the control items; this change of color is made with an FB that assignes a color code to the background with MUX command based on the value of an enumerator, this part is perfectly working but, when I'm using a touchpanel instead of a web visu (controlled by a mouse) I get into some issues as it seems that the touch operations are not triggering the MouseEnter and MouseLeave properties as it's done with the mouse.... For this reason I'm trying to add a TON to my FB and, if the enum that changes color remains at the same state for more then 3s I'm automatically resetting it to it's "0" so the item gets back the not selected color. Anyhow it looks like the TON function from library is not working in these FB that are instanced in the various visualizations, as instead they do if I create some instances within the POUS. Anyone has ideas of how to make them work?
Last updated: 2024-04-15

Post by eschwellinger on Rpi zero w lost license after 4.11 update ^{CODESYS Forge talk (Post)}
Please write to 'my question' in the CODESYS Store.
Last updated: 2024-04-16

Sort by relevance or date