Post by felipemsgarcia on Axis EtherCAT address ^{CODESYS Forge talk (Post)}
Hello, Thank you for your answer. I'm afraid I was not clear on what I was trying to achieve. I'm trying to change parameters and command axes from inside a function block and the first thing that came to my mind was pass both the EtherCAT slave and axis to the function block (as image attached). But, I believe it's worse than just pass directly the EtherCAT slave address to the function block (is it???). However I was wondering if there was a way to get the EtherCAT address directly from the axis, so I don't need to pass the EtherCAT slave nor the EtherCAT address to the function block. Thank you again!
Last updated: 2025-03-07

Post by struccc on Problem Reading Registers via Modbus from non Codesys device ^{CODESYS Forge talk (Post)}
Hi, Might be a good idea first to try out the connection and the device with some handy software, like Modbus Poll. There you can see better, what's really going on... - Is it really connected? - What error code does it return? - Can it read from the register address? - Maybe try Input registers and Holding Registers - can make a difference - Sometimes register addresses are messed up: shifted +-1 (mixing of 2 standards) - Sometimes register addresses start with offset 30000, 40000 ... - Are you using the right protocol? - Is it RTU or TCP? Maybe ASCII? - Can even have a look at the data packets, etc... All this is easier to figure out first with some modbus utility... and then to set it up in CODESYS should not be an issue. P.
Last updated: 2025-03-09

Post by aeem on CODESYS Installer does't open ^{CODESYS Forge talk (Post)}
Just downloaded stand alone setup, deleted old installer and installed new. Looked up at the installation log - MSI (c) (48:E0) [19:33:49:483]: Windows Installer installed the product. Product Name: CODESYS Installer. Product Version: 2.4.0.3545. Product Language: 1033. Manufacturer: CODESYS GmbH. Installation success or error status: 0. Installer still not running EDIT: It's working. Somehow my Windows Event Log service was disabled. I restarted the service and everything is working fine right now. Click the Start Menu or (Windows key + R) Type services.msc into the search field (Enter) Open the Services app Find a service you want to disable/enable (Windows Event Log), and double click Click Start
Last updated: 2025-04-01

Post by s1mon on Two OneWireMaster on one Raspberry PI 5 ^{CODESYS Forge talk (Post)}
Hi, I want to use two OneWireMaster on a Raspberry Pi5. I'm running Codesys Control for Raspberry Pi 64SL V 4.15.0.0. Under Linux I've configured two GPIOs for 1w bus usage on GPIO4 and GPIO27. Under Linux both masters seem to work fine and I can readout both sensors connected to both GPIOs. The two masters are 'w1_bus_master1' and 'w1_bus_master2'. In Codesys I've configured to OneWireMasters with the corresponding file paths. But in Codesys the 2nd onewiremaster "w1_bus_master2" doesn't work. Status is showing "OnewireMaster : Not running" What am I doing wrong? Does Codesys on Raspberry support multiple OneWireMasters? Any help is appreciated.
Last updated: 2025-06-10

Post by s1mon on Two OneWireMaster on one Raspberry PI 5 ^{CODESYS Forge talk (Post)}
Hi, I want to use two OneWireMaster on a Raspberry Pi5. I'm running Codesys Control for Raspberry Pi 64SL V 4.15.0.0. Under Linux I've configured two GPIOs for 1w bus usage on GPIO4 and GPIO27. Under Linux both masters seem to work fine and I can readout both sensors connected to both GPIOs. The two masters are 'w1_bus_master1' and 'w1_bus_master2'. In Codesys I've configured to OneWireMasters with the corresponding file paths. But in Codesys the 2nd onewiremaster "w1_bus_master2" doesn't work. Status is showing "OnewireMaster : Not running" What am I doing wrong? Does Codesys on Raspberry support multiple OneWireMasters? Any help is appreciated.
Last updated: 2025-06-10

Post by fedex03 on Read Global Variable from an IoT Device ^{CODESYS Forge talk (Post)}
Hello everyone, I am new to the forum, and to programming with CodeSys. I am dealing with IoT device for industry and I should check if a device is able to read/write global variables in an EtherNet/IP Master. Since I do not have an EtherNet/IP PLC, I thought of using CodeSys as a softPLC. I created a program with a set of global variables (GVL) and a task that increments them. I would like to know if I need to enable any options so that the global variables can be read by IoT devices. My device supports Class 2 Class (Explicit Messaging Connection) communication. Thank you in advance for your help.
Last updated: 2025-07-22

Post by timvh on Codesys 3.5.18.60 – Application Loss and Persistent Data Corruption ^{CODESYS Forge talk (Post)}
Which device do you use? Does this have persistent memory (e.g. NVRAM) available? Maybe first ask your PLC vendor about the possibilities and how they advice to use persistent variables? If you have no NVRAM available, CODESYS will store the variables in a file when the device gracefully shuts down. But on an abrupt power failure, this is not possible. If you have no NVRAM and you want to use persistent variables, then consider using a UPS. In this case when the power is lost, the UPS can keep the power on the PLC which then can gracefully shut down. Alternatively use the Persistence Manager to store the variable values in a file e.g. only on change. See: https://content.helpme-codesys.com/en/CODESYS%20Application%20Composer/ac_pm_overview.html
Last updated: 2025-08-26

Post by alexgooi on Codesys virtual control redundancy ^{CODESYS Forge talk (Post)}
Dear Forum, I’m currently investigating the possibilities of Codesys virtual control (Linux). The research rig consists of a PC (Debian with real time kernel) with a docker server installed on it. The PC is communicating with a Remote I/O and I have to say the performance is great. The process in the container is running (soft) real time. Currently I’m checking if it is possible to replace physical controllers by remote I/O’s and run the Codesys applications on a docker server. If I’m going into this route the reliability of the server is very important (server down, complete installation down), is it possible to make the server redundant without needing 2 separate containers (including licenses), and maintaining the real time behavior? I’m not only expecting direct answers, if you have any idea or thought they are very welcome. Kind regards Alex
Last updated: 2025-09-03

Post by monteta on Automation without UI ^{CODESYS Forge talk (Post)}
Hello all, there is my problem. i have a project on a PC A who work properly, I aim to take this project and place it on a Pc B with a blank Codesys installed. All seemd to work, the project is created on the PC B, i create my with with online.create_online_application(project.project.active_application) recover my onlineDevice and try onlinedevice.connect() so that i can use create_live_user_management() but then a problem occure on my connect() saying gateway not configured properly. I have setted my set_credentials_for_initial_user(). when i use the Ui, there is absolutely no problem. an other question, is it possible to use the Start and Stop PLC of codesys Control Systray directly in my python script? So that if it detect that it's stopped, then he automatically start it?
Last updated: 2025-09-25

Post by ton on How to create a stopwatch? ^{CODESYS Forge talk (Post)}
One i wrote this to measure elepse time When xMeasure is true is starts en when false it stops and time is messured. FUNCTION_BLOCK FB_ElapseTime VAR_INPUT xMeasure: BOOL; END_VAR VAR_OUTPUT xRisingEdge: BOOL; xFallingEdge: BOOL; tElapsed: TIME; ltElapsed: LTIME; ltPrev_Elapsed: LTIME; ltElapsedMax: LTIME; END_VAR VAR xLastValue: BOOL; LTIMEStart: LTIME; LTIMEEnd: LTIME; tonReset: TON:= (IN:= TRUE, PT:= TIME#30S0MS); END_VAR ------------------------------------------- xRisingEdge:= (xLastValue XOR xMeasure) AND xMeasure; xFallingEdge:= (xLastValue XOR xMeasure) AND NOT xMeasure; IF xRisingEdge THEN ltPrev_Elapsed:= ltElapsed; LTIMEStart:= LTIME(); END_IF IF xMeasure OR xFallingEdge THEN LTIMEEnd:= LTIME(); END_IF ltElapsed:= LTIMEEnd - LTIMEStart; ltElapsedMax:= MAX(ltElapsedMax, ltElapsed); tElapsed:= LTIME_TO_TIME(ltElapsed); xLastValue:= xMeasure; tonReset(); IF tonReset.Q THEN tonReset.IN:= FALSE; ltElapsedMax:= LTIME#0NS; END_IF Meaby this will help.
Last updated: 2023-12-09

Post by preimesbergert on Raspberry Pi 4 B HW 1.5 Codesys control 4.10.0 stopps after a few seconds ^{CODESYS Forge talk (Post)}
Wanted to play a bit with a raspberry Pi 4 Model B HW 1.5 and Codesys. Regardless of the image (tried 32bit / 64bit version from Raspberry Pi Imager) and with all tested Codesys Control versions (4.2.0, 4.8.0, 4.10.0) and regardless if single core / multicore / 64 bit variant, always is the runtime stopped after about 30sec with the nice message: ooops... this runtime was built for RASPBERRYPI. Hardware version or firmware version not supported! (-7, 0x00000BB8, 0xFFFFFFFB) Whats wrong with it?!?!? I read a lot about the issue in topics from 2020-2021 but it always was stated with new Codesys control version issue will be fixed (4.4 for example) but still it is there.
Last updated: 2023-12-21

Post by preimesbergert on Raspberry Pi 4 B HW 1.5 Codesys control 4.10.0 stopps after a few seconds ^{CODESYS Forge talk (Post)}
Wanted to play a bit with a raspberry Pi 4 Model B HW 1.5 and Codesys. Regardless of the image (tried 32bit / 64bit version from Raspberry Pi Imager) and with all tested Codesys Control versions (4.2.0, 4.8.0, 4.10.0) and regardless if single core / multicore / 64 bit variant, always is the runtime stopped after about 30sec with the nice message: ooops... this runtime was built for RASPBERRYPI. Hardware version or firmware version not supported! (-7, 0x00000BB8, 0xFFFFFFFB) Whats wrong with it?!?!? I read a lot about the issue in topics from 2020-2021 but it always was stated with new Codesys control version issue will be fixed (4.4 for example) but still it is there.
Last updated: 2023-12-21

Post by jrsantab on Remote connection to ifm PLC & HMI ^{CODESYS Forge talk (Post)}
Hello, We are trying to access remotely a PLC (ifm 711S) and a HMI (ifm CR1077). Both are connected to a Teltonika RUT200 router. We establish the connection with OpenVPN Connect and can ping both controllers. We have a laptop that, most of the time, will allow Codesys connection to the controllers, but we have several other computers that are unable to connect, although all of them can ping successfully. We cannot find any difference in the configuration or software installed from one PC to another. If we connect to the router by WIFI, instead of VPN, all the computers work fine. We know that scanning the network will not work over a remote connection, so we input the controller IP directly. Has anyone had a simlar problem and can offer any hint on what to check to meke the connection run?
Last updated: 2024-04-11

Post by jrsantab on Remote connection to ifm PLC & HMI ^{CODESYS Forge talk (Post)}
Hello, We are trying to access remotely a PLC (ifm 711S) and a HMI (ifm CR1077). Both are connected to a Teltonika RUT200 router. We establish the connection with OpenVPN Connect and can ping both controllers. We have a laptop that, most of the time, will allow Codesys connection to the controllers, but we have several other computers that are unable to connect, although all of them can ping successfully. We cannot find any difference in the configuration or software installed from one PC to another. If we connect to the router by WIFI, instead of VPN, all the computers work fine. We know that scanning the network will not work over a remote connection, so we input the controller IP directly. Has anyone had a similar problem and can offer any hint on what to check to make the connection run?
Last updated: 2024-04-11

Post by esave on OPC UA Server with on Codesys + OPC UA Client on Labview ^{CODESYS Forge talk (Post)}
Hello everyone I want a communication between my PLC as an OPC UA Server and Labview on my PC as the OPC UA Client. I have an Festo CPX-E-CEC-C1-PN PLC and I have the OPC UA Toolkit from Labview. I created some Variables for testing (see picture 1) on Codesys. I tried to use this Labview block diagram (see picture 2) but I cant connect the PLC to it. What do I have to type in the Server Endpoint URL and what in the Node ID? Is this a good way for communication with a PLC to a PC? If not is there another way?
Last updated: 2024-04-12

Post by stewnguth on New License not working. ^{CODESYS Forge talk (Post)}
Hey there, I am pretty new to the codesys space, but I got a codesys control basic M license for my raspberry pi that isntalled with no problem yesterday. Today, I went to install the visualization M locense as well because I went over the variable limit and am getting a "servernotfound" error in codesys when attempting to activate. I also tried to follow the advice in some other threads and install using a license request file on the web interface but am getting a message saying "An internal error occured" when attempting to install the license. Can anyone help me get this up and running? Thanks for your time.
Last updated: 2024-05-23

Post by spice on WebVisu Recipe Save/Load ^{CODESYS Forge talk (Post)}
I'm currently reworking the controls on a cnc press brake and wanted to load various recipes as programs to run. I'm using a 2d array of REALs to store the X and Y coordinates as well as some other program parameters in a recipe. I'd like to store all of the recipes on a computer used as the HMI that way the text files can be edited and uploaded offline. I'm using Automation Directs P2CDS-622 Can this be done through webvisu? If not would a license for Codesys HMI SL on the computer allow me to accomplish this? I've attached the Project File Thanks, Spice
Last updated: 2024-05-31

Post by ragarcia on How to change login visualization for other visualization after user logged in ^{CODESYS Forge talk (Post)}
Hello everyone, I have a web visualization on Codesys and to be able to use the web visualization first an user and a password is requested. After the user logged in, I want to automatically change the visualization to the 'Home' visualization but I am not sure how to do this. In the login visualization I basically have a button with the input configuration to execute the action 'Login' after a click. Once the user is logged in, the visualization is still stuck in the login page and I want to automatically change to Home visualization if the user was succesfully logged in. How can I know the number of web visualization clients connected to my PLC? Thanks in advance
Last updated: 2024-06-04

Post by kronlundo on Licensing info not available (WAGO PFC200 + Codesys V3) ^{CODESYS Forge talk (Post)}
Hi! We're using a WAGO PFC200 for several projects towards the energy sector, and recently upgraded to CODESYS V3. We have the "IEC 60870-5-104 Server" package in a test program, and it works well with the package in DEMO mode. However, when we acquired a license for the "IEC 60870-5-104 Server" package and tried to add the license on the PFC200 through the license manager, we get an error (see attached file). It seems like there is no CmContainer on the device, does anyone have an idea on how to fix this? We've also contacted WAGO on this issue a while back with no feedback yet.
Last updated: 2024-06-10

Post by daanyouknow on Using a raspberry pi and NVLs to log variables outside of Codesys ^{CODESYS Forge talk (Post)}
Hi, My PLC/controller doesn't support OPC UA, so my current plan to create a ringbuffer/circular logger is to connect a raspberry pi to it, use the Network Variable List receiver and sender and raspberry pi codesys runtime to get the variables to the raspberry pi, after which I will use the pi which DOES support OPC UA to get the variables to a python program which logs the desired variables for a certain amount of time for me, would this work? I don't want to spend 50+ euros + licencing fees for a solution that might not work.
Last updated: 2025-11-14

Post by jroddball79 on PM556-TP-ETH — How to change IP address without overwriting the PLC program? ^{CODESYS Forge talk (Post)}
Still looking for a solution. I have gathered more information that might help: Device: ABB AC500 PM556-TP-ETH Firmware version: 2.4.2.14993 (dated 2014) Open ports confirmed: 502 (Modbus TCP), 1200 and 1201 (CODESYS runtime). SSH (22) and HTTP (80) are not reachable. No SD card in the PLC. I can connect via Automation Builder using the current IP and Online Login works, but I have no original source project available. Automation Builder requires a full PLC download to apply IP changes, which we want to avoid as it would overwrite the running program. Any guidance on how to change the IP without a full download would be greatly appreciated. I am also open to solutions using third party tools, DCP protocol, or scripts. Thank you
Last updated: 19 hours ago

Post by danwoodlock on RPI Zero w - Edge gateway cant install ^{CODESYS Forge talk (Post)}
Hello all, First post. I recently acquired an RPI zero W from amazon, and have been using it with Codesys v3.5 SP19 patch 2. I first got it working yesterday, and after installing the runtime on the Pi, I was prompted to install the edge gateway. Installation of the edge gateway failed because of unsupported architecture, undeterred I was able to connect to the pi and program as I wanted. The issue I've noticed is that if I do not load anything to the pi overnight, I can then no longer connect to the pi and download, although I can still ping it from my pc. I found that if I power cycle the PI, I am then able to connect again, and it works as normal. I did some googling and found instances where people recommended downloading the newest edge gateway, which brings me here. Wondering if there are any suggestions, or if this is a known issue. I actually tried installing all 3 versions of edge gateway for science, but all fail with the same message. Thanks -Dan
Last updated: 2023-09-13

Post by climblinne on Calling OPC UA Methods from UaExpert ^{CODESYS Forge talk (Post)}
Hello, I hope someone could help me. I installed the newest Codesys 3.5 SP 20 Patch 1. When loading the demo files from @i-campbell I can upgrade them to the latest version and everthing works on the OPC-UA client side as expected (object "a" is visible, I can use the "ExampleMethod"). Now I * remove the "Information Model", * delete the "OPC_UA_Symbols Objects", * Add "Information Model" again * add "TestRootObjectType" again and "Generate IEC declarations" * and search for mapped instances (to get instance "a" again) Very good still working as expected. Now I delete the OPC_UA_Symbols and add it again referring to the "objecttest" from 16.9.2020. Also I redo the steps from above. The result is now, that I can't see the "a" object in the "Root/Objects" folder. Why ist this and how can I make it running? I think, it could may be a different version of the UA configuration file. I tried to build my own model definition files and got the same problem (but I am really not an expert). When someone has a actual model, which is also running in the actual Codesys I would be very grateful. Or even better, how to make the correct model in e.g. UA Modeler SW (I followed the description https://documentation.unified-automation.com/uamodeler/1.6.0/html/howprojnet_sec.html).
Last updated: 2024-07-01

Post by z870623 on About CPU Loading ^{CODESYS Forge talk (Post)}
I am running a runtime environment on an ARM A35 dual-core processor (1.5GHz) and have encountered some issues. The CPU load (both CPU0 and CPU1) occasionally spikes above 50% before returning to normal, and this happens around 2-3 times per minute. At the same time, I’ve noticed that the Max Cycle Time in the Codesys monitoring screen shows much worse performance compared to the A53 (1.2GHz), with nearly double the cycle time. The optimizations I have made so far are as follows: Set the CPU to performance mode. Isolated CPUs: CPU0 is dedicated to running Linux services and the runtime itself, while CPU1 runs the EtherCAT task and the MainTask. Despite CPU1 only running these two tasks, the utilization still increases above 50%, which I find unreasonable. Additionally, I performed tests using cyclictest both without and with the runtime running. The performance is shown in the following image: From the results, I believe the CPU performance should be fine, but I am unsure why the monitoring results are not as expected. The testing outcomes should ideally be as close as possible to the cyclictest results. Does anyone have related solutions to this issue?
Last updated: 2024-10-14

Post by mubeta on Profibus DP master with EL6731 and automatic restart of slaves ^{CODESYS Forge talk (Post)}
WHEREAS, I have already searched various posts and forums, where mostly there are few references and mostly geared toward integration in TwinCAT. I am looking for how to properly configure the EL6731 board as a DP master, (where I have its 3S license), with CoDeSys 3.5.19.x. I have three types of slaves, all integrated with their GSD descriptors. In the tab for the various slaves, I don't see options related to node restart on 'station return'. On the card manual, I read that for each slave I should be able to configure parameter 8000:2C: “8000:2C Restart behavior after DP fault Reserve, must be 0 BIT1 RW 0x00 (0dec)” However, in the project I see no way to configure this parameter, in any of the boards; and the arrays do not always have such an extensive size; most of the time they are only two or three words in size. The problem is that, after the hot reset of CoDeSys, the master restarts by starting all slave nodes, but if one or more get lost and go offline, there is then no automatic restart upon their return. I would need to figure out any solution, even via software, how to figure out that this one is back available and restart it.
Last updated: 2025-02-02

Sort by relevance or date