Post by plunje on Sensor not set ^{CODESYS Forge talk (Post)}
A got a larger project but this very small example makes it clear. I have a button, and after it's clicked a lamp should flip on and stays on, and when the mouse-button is released it should stay on. When I try that in the PLC_PRG it works, but when I change it to a function block (seet attched demo proj) it isn't. I'm fairly new to PLC programming but are very experienced C# engineer, but this goes above my head...
Last updated: 2024-05-26

Post by kris-samoy on Get Alarm status in Codesys ^{CODESYS Forge talk (Post)}
I am rather new to Codesys and I'm trying to figure out how to get the status of an alarm. This to interlock the start of a device until the alarm has been acknowledged... I am not sure if IAlarm.GetState (METH) can be used for this purpose. If yes then could someone please briefly explain how to use this? https://content.helpme-codesys.com/en/libs/AlarmManager/4.1.0.0/Interfaces/pou-IAlarm/GetState.html Thx & grtz, Kris
Last updated: 2024-06-03

Post by talhaali on Create an alarm list without use of Alarm config ^{CODESYS Forge talk (Post)}
Hi, I am trying to access active alarms in code(As alarm count variable updates only when we go to to alarm table frame in visualization). I wrote following code but it is not working: VAR iCountActiveAlarms : INT; parritfActiveAlarms : POINTER TO ARRAY[0..0] OF IAlarm; itfAlarmManagerClientAll : IAlarmManagerClient; END_VAR AlarmManager.g_AlarmHandler.GetActiveAlarms( itfAlarmManagerClient :=itfAlarmManagerClientAll, iCountActiveAlarms => iCountActiveAlarms, parritfActiveAlarms => parritfActiveAlarms); The Value is always 0. Please help.
Last updated: 2024-06-06

Post by talhaali on Create an alarm list without use of Alarm config ^{CODESYS Forge talk (Post)}
Hi, I am trying to access active alarms in code(As alarm count variable updates only when we go to to alarm table frame in visualization). I wrote following code but it is not working: VAR iCountActiveAlarms : INT; parritfActiveAlarms : POINTER TO ARRAY[0..0] OF IAlarm; itfAlarmManagerClientAll : IAlarmManagerClient; END_VAR AlarmManager.g_AlarmHandler.GetActiveAlarms( itfAlarmManagerClient :=itfAlarmManagerClientAll, iCountActiveAlarms => iCountActiveAlarms, parritfActiveAlarms => parritfActiveAlarms); The Value is always 0. Please help.
Last updated: 2024-06-06

Post by mozed on Signature verification faited fro the following package ^{CODESYS Forge talk (Post)}
Good morning, I'm trying to open a project but codesys tells me that there are certain packages that I don't have and that I need to download them. Once the installation of the packages begins, it shows me a error that the signature of certain packages does not correspond to that coming from the accepted installation context. Do you have a solution to my problem please, it is very urgent in my work. Sincerely
Last updated: 2024-06-11

Post by installwhat on C0077 on one machine but not another ^{CODESYS Forge talk (Post)}
https://forge.codesys.com/forge/talk/Engineering/thread/92c913bf7c/ Solved by changing the ethercat master version after reading the thread linked above. I think I need to read up on why this happened. I understand that placeholders should point to a particular version for obvious reasons however what has occurred in this instance is different. The example project was released as a "project archive" but it seems to load differently based on what I've got installed in my repositories. I'm going to dig into that tomorrow but any advice is welcome.
Last updated: 2024-06-11

Post by rene-h on VU.FbOpenDialog - TargetVisu - 2 x WebVisu ^{CODESYS Forge talk (Post)}
Hello, i am trying to find a way how to open Dialogs on a Single Visu. The options from VU.Globals are Target and WebVisu, but Webvisu opens the Dialog on both WebVisus and it should be separated. CurrentVisu can only be used when the Dialog is called from the Visu, but its all done in the Code. One Webvisu is for the User and one is for diagnostic reasons, and they should not be interfered from each other. Maybe someone can help me with this. Thanks
Last updated: 2024-06-13

Post by dario99 on Error when creating a new HTML5 visualisation ^{CODESYS Forge talk (Post)}
Hello, I'm quite new here. I would like to create a new HTML5 visualisation. I have already imported some templates via the visualisation elements repository, this worked fine. However, when I want to open the html5control.html in the editor or create a new project myself, I always get this error: default filesystem storage could not be found. Did you add storages.plugin to the profile? I can't find this plugin. The Package Designer (V4.1.0.0) and Codesys Visualisation (V4.5.0.0) plugins are installed Can anyone help me? Thank you very much!
Last updated: 2024-06-14

Post by rabaggett on No Visu on RasPi ^{CODESYS Forge talk (Post)}
OK, I got this to work as shown above in mos89p's comment. What I did: Tools/Update Raspberry Pi. Reloading the runtime seems to have solved the web problem. I can view the visualization on the Pi and laptop using a browser as shown above. Thanks! But Isn't the visualization supposed to take over the screen of the Raspi? When I run visu projects on Windows or Wago, the visualization shows on that device's screen by default.. But this is not happening in this case
Last updated: 2024-06-20

Post by rabaggett on No Visu on RasPi ^{CODESYS Forge talk (Post)}
Hello, I have been having trouble getting a visualization to show up on the RasPi. I have previously used both WAGO touchscreen and Windows ControlWin and had no trouble. The visu does not show on the Raspi screen on start of the program and attempts to view in a browser both on the Raspi (Chromium) and from my laptop (Brave,Chrome,Firefox) running Codesys development fail. The visu shows correctly in Codesys development when online. (Win 11) The control code that is active is operating correctly. Raspi Codesys runtime is licensed. What am I missing? Thanks!
Last updated: 2024-06-20

Post by kishan on OSCAT Scale_r function not working in LD 4.60 works in LAD2 on 3.5.21sp3 ^{CODESYS Forge talk (Post)}
here is formula for scale function you can impliment your own scale function Output=OutMin+(Input−InMin)×(InMax−InMin)(OutMax−OutMin) FUNCTION_BLOCK FB_Scale VAR_INPUT xIn : REAL; // Input value (e.g., raw sensor) xInMin : REAL; // Input range minimum xInMax : REAL; // Input range maximum xOutMin : REAL; // Output range minimum xOutMax : REAL; // Output range maximum END_VAR VAR_OUTPUT xOut : REAL; // Scaled output END_VAR VAR xGain : REAL; xOffset : REAL; END_VAR // Implementation xGain := (xOutMax - xOutMin) / (xInMax - xInMin); xOffset := xOutMin - xGain * xInMin; xOut := xGain * xIn + xOffset;
Last updated: 2025-10-26

Post by timvh on OSCAT Scale_r function not working in LD 4.60 works in LAD2 on 3.5.21sp3 ^{CODESYS Forge talk (Post)}
It seems like a bug in FBD. Work-around: If you click on the small line between the box and the output variable and delete this, the variable is removed. When you then assign a variable again (Ctrl-A), then you will see that the line will be a bit longer. If you then select the previous variable, you will see that it works.
Last updated: 2025-10-26

Post by ducng on SMC_FB_WASNT_CALLED_DURING_MOTION when enable MC_MoveRelative ^{CODESYS Forge talk (Post)}
Hello, I am using an Inovance PLC to control a servo via EtherCAT. When I enable MC_POWER, the drive switches to Run mode successfully. After that I call MC_MoveRelative, but I get the error SMC_FB_WASNT_CALLED_DURING_MOTION. The servo vibrates but the motor shaft does not move. I am new to EtherCAT/servo motion control, so I would appreciate any guidance or suggestions for troubleshooting this issue. Thank you in advance for your help.
Last updated: 2025-11-02

Post by kenth1973 on MC_Phasing state explenation ^{CODESYS Forge talk (Post)}
My MC_Phasing FB was stuck in iPhasingState=1 and error output HIGH on one axis. I could manually overwrite the state to 0 in the instance data. During normal run I see the state change from 0 to 10 to 100 back to 0 (maybe more states that I couldnt catch with the naked eye) But - what are the states numbers and their different explenations? This is not explained in the FB guide on codesys. (the pictures show state = 0 after I reset)
Last updated: 2025-11-22

Post by marciohogenelst on stablish CAN communication through the PC's USB port ^{CODESYS Forge talk (Post)}
I'm using Codesys v3.21SP4 on my PC via ControlWin to establish CAN communication through the PC's USB port. The software works fine. The CAN/USB converter works fine and is validated. However, there is no communication. Which folder and file should be modified to allow the CAN/USB converter to work and thus achieve the connection? Converter used: PCAN-View Information not yet processed: Access the folder: C:\Program Files (x86)\3S CODESYS\GatewayPLC\CODESYSControl.cfg Uncomment the line: Component.5=CmpPCANBasicDrv Any help would be appreciated.
Last updated: 2025-12-11

Post by marciohogenelst on stablish CAN communication through the PC's USB port ^{CODESYS Forge talk (Post)}
I'm using Codesys v3.21SP4 on my PC via ControlWin to establish CAN communication through the PC's USB port. The software works fine. The CAN/USB converter works fine and is validated. However, there is no communication. Which folder and file should be modified to allow the CAN/USB converter to work and thus achieve the connection? Converter used: PCAN-View Information not yet processed: Access the folder: C:\Program Files (x86)\3S CODESYS\GatewayPLC\CODESYSControl.cfg Uncomment the line: Component.5=CmpPCANBasicDrv Any help would be appreciated.
Last updated: 2025-12-11

Post by bertus on Axis directions in CNC editor not using right-hand rule? ^{CODESYS Forge talk (Post)}
Hello, Coming from robotics, I'm used to coordinate systems using the right-hand rule. But when I created below small NC program in the Codesys CNC editor, I noticed that the axis triad's Z-axis is flipped (see attached screenshot), resulting in left-hand rule. Is there a setting to change this? Or am I misunderstanding something in the CNC world? N000 G00 X0 Y0 N010 G01 X100 N020 G01 Y50 N030 G01 X0 N040 G01 Y0 N050 G01 Z25
Last updated: 2026-01-02

Post by pernockham on How to recognize licenses SMALL, MEDIUM, LARGE by CmpCodemeter ^{CODESYS Forge talk (Post)}
Solved finally, in short by: listening to eventId = EVT_CmpMgr_LicenseState, make a callback, extract the event-parameter which contains the RUNTIME_LICENSE_STATE. This gives me the license state as LICENSED / LICENSED_LOS / DEMOMODE etc. What Im not certain of at this point is this the aggregation of all three licenses or just the RUNTIME? Ie, what if my CONTROL-license is ok but my Visu-license is to low, will that set LICENSE_LOST, or would I need other listeners to find out if my VISU will shut down?
Last updated: 2026-10-07

Post by antonz on OSCAT Scale_r function not working in LD 4.60 works in LAD2 on 3.5.21sp3 ^{CODESYS Forge talk (Post)}
That's what I found as well Shaun. I have seen it at least in versions 3.5.21.1 and 3.5.21.3. There seems to be an issue with the FBD/LD package v4.6.0.0. The workaround proposed by Tim works but needs to be done manually on every code change/addition. For now we manually downgrade the FBD/LD package from v4.6.0.0 down to v4.5.0.0 after installation of CoDeSys. Same as you did. I hope this gets fixed on a next patch.
Last updated: 2025-11-21

Post by kalmeyer on NO SIGNAL ON POWER_ON FOR STEPPER MOTOR ^{CODESYS Forge talk (Post)}
I WOULD BE GRATEFUL FOR HELP....✔✔✔ I HAVE SPENT A LOT OF TIME ON THIS "SMALL" PROBLEM😢 I HAVE MADE A MC_POWER FOR STEPPERMOTOR. BUT I DO NOT GET A "HIGH" ON THE STATUS OUTPUT EVEN THOUGH PENABLE, PREG AND PDRIVESTART ARE ACTIVATED ( SEE ATTACHED WRONG_1) HAD I MADE SOME ERROR IN PLC_PRG_1..???? (WRONG_2) 1000 THANKS FOR HELP WITH THIS PROBLEM. 👀👀 /KLAUS FROM DENMARK
Last updated: 2025-11-23

Post by mrtt on Error while using Codesys SP19 Patch 4 on Windows 11 ^{CODESYS Forge talk (Post)}
Hello, same issue after a fresh install with CODESYS 64 3.5.21.30, on two different PCs Win10 and Win11. But with different Plug-In errors. CODESYS 64 3.5.19.70 runs after a lot of Package deinstallation/installation handling. But every think looks not really stable. Deinstallation of MS C++ and MS Runtime stuff -> CS installation. Than deinstallation of CodemMaster for anti freezing CS.
Last updated: 2025-11-27

Post by rtlman on Scan devices hangs CODESYS ^{CODESYS Forge talk (Post)}
Hello, I have a problem that randomly appeared today. When trying to scan a network adapter in "Deploy Control SL" the whole program hangs and needs to be restarted. I have been running "CODESYS v3.5 SP21 Patch 3" for a while and it has worked without any issues until now. I've tried upgrading to "CODESYS v3.5 SP21 Patch 4" with the same result. I've not made any system settings recently that im aware of which could cause this. Has anybody had similar a issue?
Last updated: 2025-12-12

Post by farren on Codesys complains about matching versions ^{CODESYS Forge talk (Post)}
I'm building up a 2nd PC to match an existing developer PC. Installed the same SP and Patch levels but when I open a project that was created on the existing PC, Codesys complains that it's not the same version. Attaching a screenshot..... What else is there to match? Also, can all of the libraries that are on the existing machine be copied from it to the new machine and if so, how? (So I get the same versions) Which files/folders do I copy? Thanks! -Farren
Last updated: 2025-12-14

Post by gseidel on Axis directions in CNC editor not using right-hand rule? ^{CODESYS Forge talk (Post)}
Hi bertus, the coordinate systems used in SoftMotion CNC are all right-handed. The CNC editor uses isometric projection. This can be confusing, as in your example. The y-axis seems to point into the screen, away from the viewer. However, this is just an optical effect. If you turn on the (experimental) perspective projection (must be added to the CNC tool bar using tools->customize), you can see that the coordinate system is in fact right-handed. Best regards, Georg
Last updated: 2026-01-07

Post by sheberle on ERROR: Calling the program "AlarmStorage_Prg" is not allowed from multiple tasks ^{CODESYS Forge talk (Post)}
Do you have any additional information about when the error occurs? I am trying to recreate this issue to find a workaround... Maybe you could also make the project available. You could add the following logfilter to the CODESYS configuration file: [CmpLog] Logger.0.Filter=0xFFFFFFFF Logger.0.Enable=1 Logger.0.MaxEntries=10000 Logger.0.MaxFileSize=1000000 SysSem.Filter=0xFFFFFFFF SysTask.Filter=0xFFFFFFFF I hope that the log filter will show us which task is responsible for this, so we can narrow it down a bit more.
Last updated: 2026-03-31

Sort by relevance or date