Activity for winki
-
winki posted a comment on discussion Engineering 🇬🇧
Hello, I have the same Issue !!!
-
Hello, I am wondering if it is possible to have OPCua Server with Control for linux ARM64. Indeed I am not able to add symbol configuration.
-
Hello, I have two warning on my code, and I would like to understand why. C0540: Attribut 'no_assign' missing for the 'FB_MOdbusReadHolding'. The type of the variable clientTcp is set to 'no_assign'. In this FB, I have done: clientTcp : ModbusFB.ClientTCP; clientRequest : ModbusFB.ClientRequestReadHoldingRegisters; The error comes from clientTcp : ModbusFB.ClientTCP; I am using ModbusFB 4.4.0.0. Thx a lot
-
Hello, I have two warning on my code, and I would like to understand why. C0540: Attribut 'no_assign' missing for the 'FB_MOdbusReadHolding'. The type of the variable clientTcp is set to 'no_assign'. In this FB, I have done: clientTcp : ModbusFB.ClientTCP; clientRequest : ModbusFB.ClientRequestReadHoldingRegisters; The error comes from clientTcp : ModbusFB.ClientTCP; I am using ModbusFB 4.4.0.0. Thx a lot
-
Thx for your help, I just Uninstall and install again codesys. I did it as admnistrator and now it is working... I did not change anything into the target configuration. Only my codesys on my computer. Loic,
-
Thx for your help, I just Uninstall and install again codesys. I did it as admnistrator and now it is working... I did not change anything into the target configuration. Only my codesys on my computer. Loic,
-
Hello, I used to connect into my gateway using control SL tool 4.13, (it was called Update Linux.) I formated my computer, so today I install the new version of codesys and all package. Now I am not able to connect to my PLC using control SL. It says, check the status. Normally it used to worked perfectly before that.
-
Hello, I am new on CODESYS env. I would like to do some Modbus TCP, but I am wondering If using codesys you must use the device "Modbus_TCP_Client" & "Modbus_TCP_Server". I would like to do it without device, only using ST. Is that possible ? I try the example : MODBUS_master_example, but it is not working. If it is possible to dot it without any Device I will show my code. Thx a lot
-
Your right, much easier with Linux control SL ARM. Everything is working.
-
No, my vpn is 10.0.0.12. The docker interface is 172.17.0.1.
-
I do not have error anymore using nic with eth0 value. But my network it still 172.17.0.3 like the first picture.
-
Maybe I don't know. **Maybe if someone know it can help me. ** I will try Constrol SL runtime in the Host. I will try to but only Nic without IP
-
I made a mistake it is not end0 but eth0. But I have the same error.
-
For small project, I would like to use my industrial computer as a PLC + Industrial Computer. Like that I can save the cost of one PLC. That why I am using Codesys on Linux. With the nic it is not working. I already set the IP adress with /etc/network/interfaces. Can it comes from there ? looking to "Control Linux SL" docuemntation it should work with rtu.
-
For small project, I would like to use my industrial computer as a PLC + Industrial Computer. Like that I can save the cost of one PLC. That why I am using Codesys on Linux. With the nic it is not working. I already set the IP adress with /etc/network/interfaces. Can it comes from there ? looking to "Control Linux SL" docuemntation it should work with rtu.
-
Hello, Today I am able to test ma industrial computer in my test bench. I am able to do all the configuration throught my VPN, 100% remote. I can see the gateway & the Virtual PLC. Now I would like to do some Modbus TCP Client & Modbus RS485. But I am lost due to docker ! When I go to modbus TCP it only gave me the docker network, but not my eth0 & eth01 When I go to modbus rtu, how can I create the link between Com number & my /dev/ttyRS485 Loic,
-
Thx it is working !
-
Hello, I am new on CODESYS environement. I am used to BECKHOFF env. I would like to use codesys on debian distribution. I followed this tutorial : https://www.youtube.com/watch?v=TVF0LV279_4 But I am stuck on selected the device. I do not understand, everything is running correctly Someone have an idea ? Loic
-
Hello, I am new on CODESYS environement. I am used to BECKHOFF env. I would like to use codesys on debian distribution. I followed this tutorial : https://www.youtube.com/watch?v=TVF0LV279_4 But I am stuck on selected the device. I do not understand, everything is running correctly Someone have an idea ? Loic