Post by pernockham on Is there a pragma for init/instantiation of local variables in FB (like in Methods) ^{CODESYS Forge talk (Post)}
Im using a pointer as input for a FB and for convenience I like to use 'referenced' variable internally. I use this setup in methods which works because internal variables are instantiated for each call. In a FB these variables are instantiated and initiated for the first call only. Is there a pragma/attribute available that changes this behaviour to mirror a 'method'-call?
Last updated: 2024-10-31

Post by jvfred on CodesysHMI.exe: Start Error ^{CODESYS Forge talk (Post)}
I have used Codesys HMI SL on several projects. Today I turned my PC on to start building another project and received the following error message when I tried to start my device: "CodesysHMI.exe: Start Error One of the following licenses is required: CodeMeter 101597:13 Failure reason: CmContainer Entry not found, Error 200 CodeMeterAct 5000304:13 Failure reasons: CmContainer Entry not found, Error 200" I have tried reloading HMI SL and even updated to the current version with no success. I am using HMI SL version V3.5.20.10. Any help would be greatly appreciated.
Last updated: 2024-11-01

Post by jvfred on CodesysHMI.exe: Start Error ^{CODESYS Forge talk (Post)}
I have used Codesys HMI SL on several projects. Today I turned my PC on to start building another project and received the following error message when I tried to start my device: "CodesysHMI.exe: Start Error One of the following licenses is required: CodeMeter 101597:13 Failure reason: CmContainer Entry not found, Error 200 CodeMeterAct 5000304:13 Failure reasons: CmContainer Entry not found, Error 200" I have tried reloading HMI SL and even updated to the current version with no success. I am using HMI SL version V3.5.20.10. Any help would be greatly appreciated.
Last updated: 2024-11-01

Post by jddaigle on TargetVisu controls are incorrectly positioned ^{CODESYS Forge talk (Post)}
Hello, I'm trying to run TargetVisu on my Linux IPC, and while it does work, the controls are misaligned compared to my WebVisu. Both visualizations are full-screen on a Debian 12 VM with a resolution of 1280x768. The WebVisu is running in Firefox. Are there any configuration I should adjust to ensure the controls align properly between the two? Any guidance or troubleshooting tips would be greatly appreciated! Thank you.
Last updated: 2024-11-03

Post by varshag on Trying to pull Logged In user details and certain other variable values and in turn log to a database ^{CODESYS Forge talk (Post)}
Hello All, I am new to Codesys and am trying to create a simple project which would let me log to a 6 column database table. I can use a push button on Visualization to initiate the logging. Column 1:Timestamp Column 2:Full name or Initials of Logged in operator Column 3,4,5,6: Certain variables Any help is highly appreciated. Thank you.
Last updated: 2024-11-07

Post by imdatatas on MC_CamIn did not work properly with SMC_FreeEncoder on SoftMotion 4.17.0.0 ^{CODESYS Forge talk (Post)}
Hello, I am facing a problem with the new Softmotion 4.17.0.0 version. Has anyone encountered a similar problem, what is the solution? I would be happy if you could share it. Problem description: -- "SMC_FreeEncoder" encoder axis is the master, -- The motor of the servo driver on the EtherCAT bus is the slave axis. -- When the MC_CamIn block executed, the InSync output is activated. However, although the master encoder axis position value changes, there is no movement in the slave servo axis! Test steps: 1-) EtherCAT servo axis installed, configured and motion test was performed with MC_Jog. No problem. 2-) Softmotion general axis pool > SMC_FreeEncoder was added and pulse amount configuration was performed. No problem. 3-) Incremental encoder actual count value was transferred to the "SMC_FreeEncoder.diEncoderPosition" variable as DINT under the ethercat task in every cycle and the encoder axis position value was observed. No problem. 4-) A simple CAM table with a 1:1 ratio was created under the project tree. (For example: Simply, when the encoder rotates 1 turn, the motor will rotate 1 turn.) 5-) The SMC_FreeEncoder axis enabled with MC_Power and brought to the StandStill state. 6-) The MC_CamTableSelect block was run with default input values ​​(all absolute) and only the Cam table name was specified. The Done output was seen successfully. No problem. 7-) The MC_CamIn block was activated with default input values ​​(absolute) and only the master encoder axis name, slave servo axis name, CamTableID input pins was specified and then "Execute" input set to TRUE. 8-) The InSync output information of the MC_CamIn block observed as TRUE. However, although the encoder axis value changed, the position value of the slave axis did not change at all, it did not move. It always remained at 0.0mm. 9-) When I repeated the same steps above, only changing the master axis to SM_Drive_Virtual instead of FreeEncoder and gave movement to the virtual axis, this time the slave axis moved successfully. However, when the same steps and operations are performed with the same IDE just downgrade SoftMotion version from 4.17.0.0 to 4.10.0.0, everything works normally and without problems as expected in MC_CamIn block with FreeEncoder master. (By the way, The used IDE version is Codesys V3.5 SP20patch3.) Best Regards Imdat
Last updated: 2024-11-11

Post by durallymax on Access Variable Visu Dialog ^{CODESYS Forge talk (Post)}
Is there a way to access the variable in the called dialog? Example: Text Field element with PLC_PRG.myVar as Text variable. OnMouseClick configured to write variable with keypad pop-up. OnValueChanged configured to Execute ST RND(PLC_PRG.myVar,2); Rather than change myVar with each copy of this Text Field, is there a way to access whatever the configured text variable is? Generally try to stay away from ST in visu, but was curious regardless.
Last updated: 2024-11-14

Post by selim on Need help to get RS-485 signal in Cosesys . ^{CODESYS Forge talk (Post)}
Hello Mr./Ms., I invested Raspberry Pi lot of time to get the output from the raspberry PI5. But, i did not get the signal. I use a raspberry pi 5> RS485 can hat > Modbus RTU, Industrial 8-ch analog acquisition module >weight transmitter jy-s60> S-load cell. I did not able to receive the signal from Modbus RTU to Raspberry PI5 where I use the RS 485 serial connection.
Last updated: 2024-12-01

Post by smartcoco on Request a dark mode for CODESYS ^{CODESYS Forge talk (Post)}
CODESYS IDE is not a modern IDE. Its interface is ugly, its operation is not user-friendly, its functions are lacking, its feedback is slow, and its development is not good enough. In fact, CODESYS is a helpless choice under the current situation. But this situation will not last long. For example, SIMATIC AX is a strong competitor of CODESYS, which is more open and inclusive.
Last updated: 2024-12-03

Sort by relevance or date