Post by fless on How to change bHiresMode ^{CODESYS Forge talk (Post)}
you need to set the increments to 10 (the screenshot shows 10000 hex = 65536). all the turn settings to 1. and the application units to 366. But usually you use the resolver resolution per motor turn. Insert the gear ratios (1:1 for no gear) and the last field you put the circumference of your drive wheel.
Last updated: 2024-03-12

Post by mp9876 on Attempting customizing menus fails in LADDER environment; due to free CODESYS version ? ^{CODESYS Forge talk (Post)}
That definitely does the job with the Ladder Logic Diagram type; fully equipped toolbox. Just starting with Codesys and was following programming steps which explains the choice of ladder I had picked. Thanks for the tip and have a good one! Cheers!
Last updated: 2024-03-14

Post by manuknecht on High Cycle Times for SoftMotion_PlanningTask when using AxisGroup ^{CODESYS Forge talk (Post)}
Hi, we did install the real-time kernel patch on the RPI and also performed the additional optimizations including isolating the cores. Changing the configuration of the planning task e.g. running it on a separate core, changing the cycle times and mode from cyclic to freewheeling did not show any improvements.
Last updated: 2024-03-14

Post by abinvest579 on COP instruction ^{CODESYS Forge talk (Post)}
Hi All, I have hands on rockwell software like rslogix 5000 and studio 5000. Currently started working on codesys i want to know is there any COP instruction with similar functionality in codesys like rockwell. I want to use it to split REAL into 2 INT,DINT to 2 INT also reverse 2 INT into DINT and 2 INT into REAL. Thanks in advance
Last updated: 2024-03-18

Post by markushunter on Different behavior between the "Start" button in the IDE and the Cmp function "AppStartApplication()" ^{CODESYS Forge talk (Post)}
One workaround is to create a second application which is started after the rested of the main application. The second application starts the main application after time x and is rest after done start of the main application. No problems during the fieldbus re-start by this workaround.
Last updated: 2024-03-22

Post by thysonfury on OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Post)}
Hi after some assistance with an error on a Groov PR2 PLC. We have a few different communications set up as shown below: One Modbus TCP Slave Connection - ( Sending / Receiving Data from a PC ) Two Modbus TCP Master Connection - ( Reading Data from a UPS Panel and Reading Data Gas Chromatograph) One Modbus RTU Slave Connection 485 - (Reading Data from a fire and gas panel) One Modbus RTU Master Connection 485 - (Sending Data to a Telemetry Unit) All Licenses have been installed as per OPTO22 suggestions of the order below: Modbus TCP Master Modbus TCP Slave Modbus RTU Master Modbus RTU Slave When I check on License manager the RTU Master license seems to disappear on installing the RTU. (What ever reason I’ve been told this is “normal”). If I use Device License Read It will successfully read all the licenses correctly. Now the issue is every 2 hours and between 4. For what ever reason the communications seems to end and lock up for about 20 seconds. During this time even if I was logged into the PLC it would kick me off and I’d have to re type the password to enter. Most of the devices can handle this however the RTU flags up a communications failure at the SCADA and is raising alarms every 2 hours and 4 mins. We’ve had multiple people go through the code to check for anything obvious. Does anyone have any ideas?
Last updated: 2024-04-15

Post by thysonfury on OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Post)}
Hi after some assistance with an error on a Groov PR2 PLC. We have a few different communications set up as shown below: One Modbus TCP Slave Connection - ( Sending / Receiving Data from a PC ) Two Modbus TCP Master Connection - ( Reading Data from a UPS Panel and Reading Data Gas Chromatograph) One Modbus RTU Slave Connection 485 - (Reading Data from a fire and gas panel) One Modbus RTU Master Connection 485 - (Sending Data to a Telemetry Unit) All Licenses have been installed as per OPTO22 suggestions of the order below: Modbus TCP Master Modbus TCP Slave Modbus RTU Master Modbus RTU Slave When I check on License manager the RTU Master license seems to disappear on installing the RTU. (What ever reason I’ve been told this is “normal”). If I use Device License Read It will successfully read all the licenses correctly. Now the issue is every 2 hours and between 4. For what ever reason the communications seems to end and lock up for about 20 seconds. During this time even if I was logged into the PLC it would kick me off and I’d have to re type the password to enter. Most of the devices can handle this however the RTU flags up a communications failure at the SCADA and is raising alarms every 2 hours and 4 mins. We’ve had multiple people go through the code to check for anything obvious. Does anyone have any ideas?
Last updated: 2024-04-15

Post by thysonfury on OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Post)}
Hi after some assistance with an error on a Groov PR2 PLC. We have a few different communications set up as shown below: One Modbus TCP Slave Connection - ( Sending / Receiving Data from a PC ) Two Modbus TCP Master Connection - ( Reading Data from a UPS Panel and Reading Data Gas Chromatograph) One Modbus RTU Slave Connection 485 - (Reading Data from a fire and gas panel) One Modbus RTU Master Connection 485 - (Sending Data to a Telemetry Unit) All Licenses have been installed as per OPTO22 suggestions of the order below: Modbus TCP Master Modbus TCP Slave Modbus RTU Master Modbus RTU Slave When I check on License manager the RTU Master license seems to disappear on installing the RTU. (What ever reason I’ve been told this is “normal”). If I use Device License Read It will successfully read all the licenses correctly. Now the issue is every 2 hours and between 4. For what ever reason the communications seems to end and lock up for about 20 seconds. During this time even if I was logged into the PLC it would kick me off and I’d have to re type the password to enter. Most of the devices can handle this however the RTU flags up a communications failure at the SCADA and is raising alarms every 2 hours and 4 mins. We’ve had multiple people go through the code to check for anything obvious. Does anyone have any ideas?
Last updated: 2024-04-15

Post by nano on CODESYS Edge Gateway for Linux on embedded distribution ^{CODESYS Forge talk (Post)}
yocto isn't the part. which architecture you are using? arm, x86, 32bit?, 64bit? normally u can use the deliveral from store and integrate it into yocto. for resolv the dependencies, its best way todo using an recipe and let yocto do prebuildchecks jefore the install-commands
Last updated: 2024-04-17

Post by bryandimino on OPC Da Server Code Meter Issues after Enabling License ^{CODESYS Forge talk (Post)}
I'm trying to get the OPC server setup on my machine and currently I'm not having luck. I went ahead and got my license setup. However when I go to run WinCoDeSysOPC.exe I get an error message that I don't have the code meter licenses installed. Does anyone have any ideas on how I can fix this issue?
Last updated: 2024-05-02

Post by micik on CAA File- FILE_OPERATION_DENIED error ^{CODESYS Forge talk (Post)}
Hello, I'm trying to use FILE.Open to open file that exists in the given location. sFileName is formed from "Copy as path" in Windows. So I'm sure file exists and it is in the given location. And still, I get thiss denied error. What could be the problem here? Attached is a screenshot with current implementation.
Last updated: 2024-05-16

Post by felipemsgarcia on Generic EtherCAT slave ^{CODESYS Forge talk (Post)}
Hello, Without much info, I would assume that this is an optional object on the EtherCAT network and it's either disconnected or the address doesn't match. I would look into the devices manual or contact the manufacturer for further assistance. And, I would have posted a new topic instead of using a non related one... Cheers!
Last updated: 2024-05-16

Post by schnepper on How to delete main action from SFC Step ^{CODESYS Forge talk (Post)}
I added a main action to an SFC step, and then tried to delete it. There is no delete option in the SFC menu nor in the right click menu of the step. I deleted the action from the device tree, but building results in and error saying the action is not defined. Is there a way to delete a main action?
Last updated: 2024-05-23

Post by vitorp on Visualization Toolbox in German ^{CODESYS Forge talk (Post)}
Hello, I am new to Codesys. I installed it on my computer and set the language to English. Most of the localized text appears in the correct language, but the Visualization Toolbox and the element properties are in German. I haven't found a way to change them to English. Can someone help me with this?
Last updated: 2024-06-17

Post by pharus on Setup problems with PiXtend ^{CODESYS Forge talk (Post)}
Hello all, I have an PiXtend V2L complete kit and installed everything like in the manual. Ive installed Codesys V3.5 S20 Codesys Control for Raspberry Pi PiXtend_V2_Professional_for_CODESYS.package But as soon as i Create a Project, i get a lot of error messages, and i cant find the PLC via Ethernet Thanks a lot
Last updated: 2024-06-19

Post by pharus on Setup problems with PiXtend ^{CODESYS Forge talk (Post)}
Hello all, I have an PiXtend V2L complete kit and installed everything like in the manual. Ive installed Codesys V3.5 S20 Codesys Control for Raspberry Pi PiXtend_V2_Professional_for_CODESYS.package But as soon as i Create a Project, i get a lot of error messages, and i cant find the PLC via Ethernet Thanks a lot
Last updated: 2024-06-19

Post by pharus on Setup problems with PiXtend ^{CODESYS Forge talk (Post)}
Hello all, I have an PiXtend V2L complete kit and installed everything like in the manual. Ive installed Codesys V3.5 S20 Codesys Control for Raspberry Pi PiXtend_V2_Professional_for_CODESYS.package But as soon as i Create a Project, i get a lot of error messages, and i cant find the PLC via Ethernet Thanks a lot
Last updated: 2024-06-19

Post by pharus on Setup problems with PiXtend ^{CODESYS Forge talk (Post)}
Hello all, I have an PiXtend V2L complete kit and installed everything like in the manual. Ive installed Codesys V3.5 S20 Codesys Control for Raspberry Pi PiXtend_V2_Professional_for_CODESYS.package But as soon as i Create a Project, i get a lot of error messages, and i cant find the PLC via Ethernet Thanks a lot
Last updated: 2024-06-19

Post by kuegerls on SysProcessExecuteCommand2 and CANopen Device ^{CODESYS Forge talk (Post)}
I have now conducted some tests. The problem occurs when the Python script establishes an OPCUA connection, even if I only establish the connection without reading or writing any data. Is there another way to exchange data between Python and CODESYS without having to put in a lot of effort?
Last updated: 2024-06-24

Post by timvh on Persistent Retain Variables Not Visible in Online View (WAGO PFC100 + CODESYS) ^{CODESYS Forge talk (Post)}
It is a known issue. It only happens with CODESYS and Wago controllers and the Persistent Variables. It seems related to using 64 bit variables in the PV list (e.g. LREAL). Internally in the PLC everything works okay. It is just a monitoring issue.
Last updated: 2025-10-26

Post by scrisp on Source code changes since last download ^{CODESYS Forge talk (Post)}
Why does CODESYS 3.5 show the message “Source code changes since last download” even though I did not create or modify any new variables? When I go online with the PLC, it detects changes and suggests synchronizing, but nothing was actually changed in the project. What could cause this and how can I fix it?
Last updated: 2025-11-28

Post by gseidel on SMC_ERROR SMC_CGR_INVALID_POSPERIOD ^{CODESYS Forge talk (Post)}
Hi blitz, that usually means that the modulo period, when converted to increments, is larger than 2^31. (The bus bandwidth is usually 2^32.) What is your "technical unit", do you program in angular degrees? And what is the modulo period? If you want you can post the drive configuration (screen shot of the "General" and "Scaling/Mapping" page). Best regards, Georg
Last updated: 2025-12-16

Post by robinep on PM564 online problem ^{CODESYS Forge talk (Post)}
Hi I'm beginner in codesys There is a PM564 ABB Plc in a machine and I am going to upload plc program The connection with plc is established with tk503, Codesys is online and show plc status, How can I upload the program in PLC? I don't have any source code. regards
Last updated: 2026-09-26

Post by timvh on Legacy IFM CANopen I/O modules with CR710S / CODESYS 3.5 ^{CODESYS Forge talk (Post)}
I don't work for IFM, nor for CODESYS and didn't create the .eds file or developed the CAN protocol. I have no knowledge of the exact contents and SDO's or PDO's which are exchanged. So no, I am not sure. But if the .eds file confirms to the CANopen specifications, why shouldn't it?
Last updated: 2026-10-02

Post by blitz on SMC_ERROR SMC_CGR_INVALID_POSPERIOD ^{CODESYS Forge talk (Post)}
Codesys - SMC_ERROR SMC_CGR_INVALID_POSPERIOD - Invalid modulo period less than or equal to zero or greater than half the bus bandwidth. Has anyone seen this error and actually understands what it means and how to get rid of it? I tried to work around it by reducing the number of increments on the drive but then the drive itself starts throwing errors.
Last updated: 2025-12-15

Sort by relevance or date