Post by shivsrikakolum on Getting SMC_ERROR 34 SMC_AXIS_NOT_READY_FOR_MOTION, while the axis should be ready for motion ^{CODESYS Forge talk (Post)}
how did you manage to get rid of the error. i have set the cycle time to 2000 microsecond but my softaxis is still amber warning
Last updated: 2026-07-07

Post by konstantin on CAM Motion Recover after STO ^{CODESYS Forge talk (Post)}
Hello Mr. Seidel, both the master and the slave axis are modulo. Basically the situation is as follows: One master cycle is 100 units. Slave's modulo length is 2000 units. In the CAM table I defined 10 master cycles on X axis - 1000 units and on the Y axis is the slave - 2000 units. Then depending on the master position 0 to 1000 units the slave's position is plotted on the Y axis - 0 to 2000 units. For example, while the master is executing the 3rd cycle i.e. above 200 units, I trigger the STO function of the slave and it stops. The master executed his cycle but the slave was stopped during the execution. How can I set the slave to continue the CAM sequence from the point where it stopped i.e. third cycle of the master? When I reset the slave error and sync again, everyrhing starts from master's 0 position. Best Regards Konstantin Kolev
Last updated: 2026-02-13

Post by srouse on PFC200BUS not running ^{CODESYS Forge talk (Post)}
I started a project in codesys for a WAGO 750-8212 PLC and I am working on getting online with the controller. I can log in to the controller and I can see and control all of the fieldbus couplers that I have. I am unable to get the internal bus working. It just says that the bus is not running and when I scan or devices nothing shows up. Am I missing something important in my device tree?
Last updated: 2024-07-10

Post by polo on 1 Wire und i2c zeitgleich in Betrieb ^{CODESYS Forge talk (Post)}
Hallo zusammen, ich habe schon einige Zeit 16 DS18B20 am 1 Wire laufen ... auch die ganze Zeit stabil ... jetzt habe ich ein PWM Signal über i2c für eine Pumpenansteuerung zusätzlich in Betrieb genommen.. nur das Signal für die Pumpe geht über i2C ... 100Hz 10ms. Es läuft auch alles soweit ... nur fallen mir jetzt die Temperaturen in Abständen aus ... Vertragen sich die beiden Systeme zeitlich evtl. nicht so gut ... 1 wire extra task mit 200ms Prio 0 i2c task 10ms ... damit die 100Hz auch übertragen werden Prio 1 (Adafruit_PWM) Main Task 20ms Prio 5 Oder jetzt besser beides über i2c abrufen ... ist aber dann evtl. für die DS18B20 zu schnell ? Oder sind die 5V vom Pi jetzt zu schwach für beide Signale? Vielen Dank euch
Last updated: 2026-04-27

Post by sturmghost on Initialization of visualization variables and cyclic code execution ^{CODESYS Forge talk (Post)}
I'm looking for a smart and short way to implement initialization of visualization variables depending on the visualization input. For an easy example consider a rectangle which rests at XPos := 0 when the input state is false and at XPos := 50 when the input state is true. My visualization variables look like this: VAR_IN_OUT State : BOOL; END_VAR VAR XPos : INT; END_VAR I put this rectangle via a visualization frame element into another visualization and link a frame reference variable with the state to it. If the variable is true, the rectangle should rest at XPos := 50 and false at XPos := 0 at visualization init but how should I assign the 50 or 0 to the internal visualization variable XPos? I would need some init-methode for the visualization but I dont want a global init-method for such tasks. I want to do it inside of the visualization element but I can't see any solution for this? It would be good to be able to define ST-code within the visualization element which runs cyclic at each VISU_TASK task-cycle then I could just check the input state and change the XPos accordingly. Does someone have a solution?
Last updated: 2023-10-01

Post by open on How to create a stopwatch? ^{CODESYS Forge talk (Post)}
Hi @ph0010421, I tried the program the TimeTaken is calculated when stop is triggered. I want the TimeTaken to be continuously calculated and counting when a BOOL variable is true. I tried to program this way: Declaration: PROGRAM PLC_PRG VAR bStartStop: BOOL := FALSE; // Start/Stop button bReset: BOOL := FALSE; // Reset button bRunning: BOOL := FALSE; // Flag indicating whether the stopwatch is running tStartTime: TIME; // Variable to store the start time tElapsedTime: TIME; // Variable to store the elapsed time END_VAR Implementation: // Main program logic IF bReset THEN // Reset button pressed, reset the stopwatch bRunning := FALSE; tElapsedTime := T#0s; ELSIF bStartStop THEN // Start/Stop button pressed, toggle the running state IF bRunning THEN // Stop the stopwatch bRunning := FALSE; ELSE // Start the stopwatch bRunning := TRUE; tStartTime := tElapsedTime; END_IF; END_IF // Update the elapsed time when the stopwatch is running IF bRunning THEN tElapsedTime := tElapsedTime + T#1s; // Adjust the time increment as needed END_IF However counting of the seconds is not accurate. I tried changing the main task cycle time interval to 1000ms. The counting of seconds become slower. (see attached) Please help
Last updated: 2023-12-08

Post by mondinmr on Direct Pointers in IOMapping for EtherCAT with IoDrvEthercatLib.ETCSlave_Dia ^{CODESYS Forge talk (Post)}
Using SDO, I can read the EtherCAT mappings and offsets from various registers like 0x1c12, 0x1c13, etc. When I obtain registers mapped in the PDOs and various offsets, I could technically access directly to the statusword, controlword, etc., if they are mapped. I have noticed that on IoDrvEthercatLib.ETCSlave_Diag I can find pointers to the input and output buffers. However, although the input buffer can be easily read by referring to what has been obtained from the SDOs, it is not possible to write to the output buffer, as it is overwritten in each cycle by the data from the IOMapping task. Is there a way, knowing an instance of IoDrvEthercatLib.ETCSlave_Diag, to obtain the pointer to the first data in the IOMapping? The offsets are identical to those of the PDOs, but obviously the data is a copy. For me, the cleanest thing would be to access the pointers on IOMapping, for DS402a devices to retrieve the key data and point them to internal references. I need to know this as, having developed our own motion library, I would like to simplify the initial setup by eliminating unnecessary and nonsensical mappings that can lead users to unnecessary errors. In the current version that we have been using for years, we have to map everything manually. I would like to pass only the slave reference to the FB_init constructors and eliminate the mapping.
Last updated: 2024-02-12

Post by hbuitrago on CmpIecTask-program loaded exception ^{CODESYS Forge talk (Post)}
I'm facing an error that show on the codesys and the PLC that dont let either the PLC run or access it using the remote software, Error: program loaded exception Log: exception position:IP=0x0xfffffffe (no IEC context could be retrieved) component: CmpIecTask exception [accessviolation] ocurred: APP=[application], Task=[Task] POU changed, that inhibits an online change, Plase let me know if there is a solution for this issue, Best regards,
Last updated: 2024-09-06

Post by rossanoparis on RevPi CONNECT+, CODESYS, EtherCAT master "Filedbus lost synchronicity" ^{CODESYS Forge talk (Post)}
Hello @rmaas I assume, you've already verified and tuned everything regarding the EtherCAT network. In my case the problem was due to a wrong core assignement. I suggest to not use the core #0 for your EtherCAT task. The OS realtime patch, which is present on RevPi OS, uses the core #0 for its porpouses and it mustn't be used by any other task which requires realtime and deterministic features. regards Rossano
Last updated: 2024-04-11

Post by nz-dave on *exception* [processorloadwatchdog] occurred in: app=[all], task=[all] ^{CODESYS Forge talk (Post)}
Can anyone shed some light on this issue im having. at random, sometimes days, sometimes weeks or months. i get this error and have to reset the plc. Im using a Weintek HMI with ethernet/ip remote io and vsd. i have tried increasing my task times and watchdogs. and when i view my PLCload in the shell its normally around 3-4%, highest ive ever seen is 7%. Nothing i do seems to help the issue. Could the HMI's Codesys CPU be getting to hot do to high ambient temp?
Last updated: 2026-02-01

Post by janderson on Ethercat scan for devices not picking up EL7041 as a softmotion axis ^{CODESYS Forge talk (Post)}
I have a beckhoff EL7041-1000 rev 21 in my ethercat bus but it wont correctly create a softmotion axis unless i manually insert the device. scan for devices gives me an el7041-1000 without an SM3 axis.
Last updated: 2023-09-02

Post by conny-nm on onewire bus master stop working after 4.8.0.0 upgrade ^{CODESYS Forge talk (Post)}
Habe ein ähniches Problem Ethercat läuft nur mit RT 4.8.0.0 nicht aber Onewire. Füge ich ForceFile läuft Onewire, nicht Ethercat. Bei IecFilePath.3 läuft Ethercat nicht aber Onewire
Last updated: 2023-09-20

Post by augmue on onewire bus master stop working after 4.8.0.0 upgrade ^{CODESYS Forge talk (Post)}
ich lese alle 4 Sekunden einen Sensor DS18B20 aus Datei im Verzeichniss /mnt/1wire mit USB-Adapter und owfs [SysFile] IecFilePath.3=/mnt/1wire
Last updated: 2023-09-20

Post by conny-nm on onewire bus master stop working after 4.8.0.0 upgrade ^{CODESYS Forge talk (Post)}
Danke für die Hilfe habe ich übersehen. Habe zwischenzeitlich ein neues Betriebssystem aufgespielt und jetzt wieder meinen alten Fehler das die Runtime nur ca. 20 Sekund läuft.
Last updated: 2023-09-21

Post by timvh on displaying all incoming CAN bus messages ^{CODESYS Forge talk (Post)}
Create a (global) array of Messages: aMessage : ARRAY[0..NR_OF_MESSAGES-1] OF CAN.RxMESSAGE; Then add each received message to the array. IF UserVarGlobal.g_countMsg_RPMset < NR_OF_MESSAGES THEN aMessage[UserVarGlobal.g_countMsg_RPMset] := Message; UserVarGlobal.g_countMsg_RPMset := UserVarGlobal.g_countMsg_RPMset + 1; END_IF
Last updated: 2024-07-22

Post by pernockham on PHOENIX CONTACT Axioline PLCnext project in CodeSys SodftPLC ^{CODESYS Forge talk (Post)}
The structure should be the same independent of which runtime version. Im using Codesys control for linux SL. Ie, add an ethernet device, then profinet controler then phoenix PN bus coupler.
Last updated: 2025-09-09

Post by lostcontrol on Remote Ethernet/ip Adapter communication with scanner running on codesys ^{CODESYS Forge talk (Post)}
is the bus running.? what type of values/IO is the adaptor providing? do you have a map of the data layout? are you actually looking at the right offset?
Last updated: 2023-12-16

Post by elektron785 on CAN-Bus in Demo-Version ^{CODESYS Forge talk (Post)}
Ja, Gerätebaum ist grün/orange (siehe Bild). IO-Variablen sind gemappt und im Programm verwendet. Ich habe mal noch ein paar Bilder zum Status angehangen.
Last updated: 2024-02-07

Post by davidbo on Does CODESYS use its own native driver for I2c? ^{CODESYS Forge talk (Post)}
CODESYS Control for Raspberry Pi MC Does CODESYS use its own native driver for I2c? I have a python script communicating with a device simultaneously with a CODESYS doing the same. The bus is not saturated. But I get many read errors
Last updated: 2024-02-13

Post by elektron785 on CAN-Bus in Demo-Version ^{CODESYS Forge talk (Post)}
Es funktioniert nun. Ich hatte die SYNC-Erzeugung im CANOpen-Manager vergessen. Mit dessen Aktivierung empfange ich die Daten in der Soft-SPS. Vielen Dank für die Hilfe bis hierhin :) Btw: Die PDO's waren standardmäßig als Übertragungstyp zyklisch-synchron eingestellt.
Last updated: 2024-02-14

Post by davelewis104 on J1939 SA ^{CODESYS Forge talk (Post)}
I am curious if there is a function block or function that will allow me to monitor the J1939 CANBus and pull out all of the SAs that are on a particular bus, without having to have them loaded in the J1939 manager?
Last updated: 2024-04-30

Post by eschwellinger on Ethercat bus on Beckhoff CX with Codesys for Linux ^{CODESYS Forge talk (Post)}
yes I think you need to build the kernel drivers for the CCAT driver for the backplane ETC networkcard https://github.com/Beckhoff/CCAT/
Last updated: 2024-05-13

Post by shivsrikakolum on SOFTMOTION - Error 34 when trying to execute and SMC_DI_AXIS_Error ^{CODESYS Forge talk (Post)}
I am using a Trio DX3 drive DC bus Unused , so I can control from SM3 Axis Datatype but as soon i try to Jog or Enable the MC_ Blocks It shows Error 36 can some one please the settings for this .
Last updated: 2026-07-07

Post by eschwellinger on Beckhoff CX9240 : Using Internal EtherCAT Bus ^{CODESYS Forge talk (Post)}
yes, you need to install Control RTE CX. In that package there is the Internal EthercatMaster / EthercatMasterSoftmotion which you could add then.
Last updated: 2026-07-10

Post by arj3090 on Beckhoff CX9240 : Using Internal EtherCAT Bus ^{CODESYS Forge talk (Post)}
I installed Linux ARM SL and it recognizes the RJ45 ethernet ports, but I cannot get it to recognize the internal port for the IO cards.
Last updated: 2026-07-10

Sort by relevance or date