Post by daanyouknow on Using a raspberry pi and NVLs to log variables outside of Codesys ^{CODESYS Forge talk (Post)}
Hi, My PLC/controller doesn't support OPC UA, so my current plan to create a ringbuffer/circular logger is to connect a raspberry pi to it, use the Network Variable List receiver and sender and raspberry pi codesys runtime to get the variables to the raspberry pi, after which I will use the pi which DOES support OPC UA to get the variables to a python program which logs the desired variables for a certain amount of time for me, would this work? I don't want to spend 50+ euros + licencing fees for a solution that might not work.
Last updated: 2025-11-14

Post by hickan on safety cpu cannot go online ^{CODESYS Forge talk (Post)}
Hi! I am using abb ac500 in automation builder v2.7 I have a problem with a new project. In the normal mode I have no problems, but in safety mode i cannot go online. I get 'Communication Error (#0) Logout Performed' message. I have tried changing the adress (level 1) in communication parameters. I tried 0.0.0.0.0 and 0.1.0.0.0 and 1.1.0.0.0 but it did no difference. What do you think could be causing this? Thanks!
Last updated: 2025-07-08

Post by tomast on Codesys and Siemens SINAMICS 20 modbus RTU "Response CRC Fail" ^{CODESYS Forge talk (Post)}
Hi everyone, I'm currently working on a project involving the control of 5 VFDs via Modbus RTU, this time using the WAGO 750-8212 CPU. So far, I've managed to make progress, but I've encountered an issue. While I can successfully read and write to all the registers I need, I consistently encounter a "Response CRC Fail" error when attempting to write the value 1151 to the STW register at address 40100. I'm able to set the frequency via register 40101 and adjust all other parameters using different registers. Setting STW to 1150 results in the drive ready boolean from the ZSW-bit being received instantly. However, the moment I attempt to send 1151 to register 40100, I immediately receive the "Response CRC Fail" error for all channels. I've also attempted to use combined control, employing Modbus for frequency control and starting from a digital input. Everything seems to function properly until I send the start command to the VFD. Interestingly, I consistently encounter the same error the moment I send the start command, regardless of whether I use register 40006 (high) or 40100 (1151). Could someone please assist me in resolving this issue?
Last updated: 2024-03-21

Post by andrea199403 on Assigning Modbus addresses to a structure in a dynamic way ^{CODESYS Forge talk (Post)}
Hello everyone, I am new to this forum and I am also new to Codesys programming. My problem is this: I have a STRUCT of 64 bool and 30 real, this STRUCT is assigned in the programme 9 times. Now I need to communicate with an HMI via Modbus and I have defined the slave device and created the holding registers for communication. I would like to declare the first call of the STRUCT on the Modbus registers %QX2000.0 to %QX2007.7 for the booleans and on the registers %QW1004 to %QW1034 for the real registers. That said, I would like to change an index and set an offset of 100 bytes for the calls of the other 8 assignments, so that the result is: %QX2100.0 to %QX2107.7 for the booleans and on the %QW1104 to %QW1134 registers for the Real registers, etc. Is there a way to declare this? Thank you very much.
Last updated: 2025-10-21

Post by rk-gaw on Unhandled exception and refactoring error ^{CODESYS Forge talk (Post)}
Hello everyone. I hope this is the right place to ask for help, this error is causing me a great amount of time loss and I really would like to end this nightmare. I don't know why but at times if I try to Browse -> Display Cross Reference on a variable Codesys just crashes. I'll attach the file with the complete crash report hoping someone can figure why it happend. I think that the unhandled exception comes from the PersisranceManager Module and is connected with the other big problem I'm facing: I cannot refactor in my project, if I'll try to refactor a POU name the whole POU will become "frozen", it's like its desynchronizing from the project and the project cannot find the pointer to the POU once I refactor it. And when I open the project a warning pop-up will show up with the frozen POUs name, but I cannot figure out what the warning is telling me. I'll attach every warning and error pop up the project is showing me, and thanks in advance to anyone who can figure something out.
Last updated: 2025-12-10

Post by i-campbell on Official MQTT-Client: MAX_RECEIVE_BUFFER_SIZE_EXCEEDED ^{CODESYS Forge talk (Post)}
I can't answer why it's not resetting, but from the description of g_udiMaxReceiveBufferSize, I would guess the sum of sizes of the mqtt packets received in one cycle exceeded this value. So the answer may be to increase that parameter. https://content.helpme-codesys.com/en/libs/MQTT%20Client%20SL/Current/MQTT-Client/Common/Params/MQTTParam.html https://content.helpme-codesys.com/en/CODESYS%20Development%20System/_cds_dlg_library_parameter.html
Last updated: 2023-09-26

Post by tk096 on Some 'pathetic' errors in SoftMotion program ^{CODESYS Forge talk (Post)}
Hi, I suppose that you are referring to the error code "SMC_FB_WASNT_CALLED_DURING_MOTION"? Starting of Softmotion version 4.15.0.0 the instance path of the function block that has not been called is logged into the device log. This might help you to identify why it has not been called.
Last updated: 2024-07-18

Post by timvh on Array to String ^{CODESYS Forge talk (Post)}
The new (UTF8) string library is faster and can handle large strings. https://content.helpme-codesys.com/en/CODESYS%20String%20Libraries/_strlib_start_page.html PS, in CODESYS, the maximum string length is not 255 characters. The String functions of the standard library are limited to strings of 255 characters. But you can use other (memory) functions to handle strings larger than 255 characters.
Last updated: 2024-07-22

Post by marks on Regarding trend storage access error ^{CODESYS Forge talk (Post)}
I had this problem when running the application as a Simulation. When I wrote it to the Pi all worked as expected. If this isn't the case for you, we've seen some issues with sqlite on the Pi's - so reset Origin and re-download may help in that case. Good luck, Mark
Last updated: 2024-07-24

Post by jmfernandes on OpenDir always in error ^{CODESYS Forge talk (Post)}
Thanks for the answer Tim. I am using the codesys version 3.5 SP16, is this also affected or only after version 19? But now at leastI know that is an acess problem to the file and not something else. Unfortunately the link you posted on 2023 are now dead, but I will investigate!
Last updated: 2024-08-01

Post by egau on Hard shutdown: no code on device after power on ^{CODESYS Forge talk (Post)}
Hi, thanks for the fast response :) Yes I Have a .err file. Sorry I forgot to upload it. It is a binary file though... "Runtime goes in exception before the shutdown ?" I think it goes into exception at the same time as the power is lost...
Last updated: 2024-10-03

Post by bertcom on Converting each character to a string into ASCII ^{CODESYS Forge talk (Post)}
@TimvH, Thank you, i think this way i can seperate the complete string to characters. Next part of the topic is converting the characters to an ASCII code. Is there an standerd function in Codesys for this? I alredy searched a few hours for it on the internet. no succes.
Last updated: 2024-11-11

Post by nz-dave on Ethernet/IP Scanner Exception ^{CODESYS Forge talk (Post)}
HI I have had a project running for a few weeks and twice it has shut the program down due to this exception. exception[ProcessorLoadWatchdog] occurred in: App=[all], Task[all] I have to reboot (power cycle) the system to clear the exception. or remotely restart the application. Any ideas? Cheers
Last updated: 2024-11-16

Post by winki on Warning attribut no_assign ^{CODESYS Forge talk (Post)}
Hello, I have two warning on my code, and I would like to understand why. C0540: Attribut 'no_assign' missing for the 'FB_MOdbusReadHolding'. The type of the variable clientTcp is set to 'no_assign'. In this FB, I have done: clientTcp : ModbusFB.ClientTCP; clientRequest : ModbusFB.ClientRequestReadHoldingRegisters; The error comes from clientTcp : ModbusFB.ClientTCP; I am using ModbusFB 4.4.0.0. Thx a lot
Last updated: 2025-01-10

Post by winki on Warning attribut no_assign ^{CODESYS Forge talk (Post)}
Hello, I have two warning on my code, and I would like to understand why. C0540: Attribut 'no_assign' missing for the 'FB_MOdbusReadHolding'. The type of the variable clientTcp is set to 'no_assign'. In this FB, I have done: clientTcp : ModbusFB.ClientTCP; clientRequest : ModbusFB.ClientRequestReadHoldingRegisters; The error comes from clientTcp : ModbusFB.ClientTCP; I am using ModbusFB 4.4.0.0. Thx a lot
Last updated: 2025-01-10

Post by mucleus on How do I fix ";Internal Error (x86-64): Invalid type size" error? ^{CODESYS Forge talk (Post)}
I opened the project file of version 3.5.19.7 in 3.5.21.0. I updated all the environment of the project to the latest and compiled it. When I compile it, I get an error ";Internal Error (x86-64): Invalid type size". How can I fix this error? I will wait for your help.
Last updated: 2025-04-15

Post by nano on Creating, using an external Function. ^{CODESYS Forge talk (Post)}
the Answer is easy, you don't reapecting the codesys-behaviour and pre-request on a dll/so like you like to create. codesys won't load it about the fact that the dll isn't registered in codesys. check this page for more informations: https://content.helpme-codesys.com/en/CODESYS%20Control/_rtsl_extension_extension_sdk.html
Last updated: 2025-05-14

Post by astrum on OPC UA Information Model Error "Dimensions must be empty" ^{CODESYS Forge talk (Post)}
Hello everyone, does anyone know what this error means: Internal Error in code generation for http://opcfoundation.org/UA/DI/: Dimensions must be empty. I use the standard information models from Codesys and haven't even called the Information Model, but my program can't compile. the only thing I did was to insert the Communication Manage.
Last updated: 2025-08-11

Post by kporter on Removing <Empty> node in Device Tree ^{CODESYS Forge talk (Post)}
I initially created a SoftMotion axis for my EtherCAT CoE drive. I wanted to change it to use SoftMotionLight so I deleted the SM node, which left an <empty> node. I created the SML device, but the <empty> node remains. How can I remove that from the tree? </empty></empty>
Last updated: 2025-09-06

Post by beavel on Opening and saving files with fileOpenSave dialog ^{CODESYS Forge talk (Post)}
1 + Replying in hopes of getting an answer here. I would also like to modify the look of the FileOpenSave Dialog. I have successfully adjusted the looks of the User management Dialogs but can not find a library file to adjust this particular one. Any help would be helpful. @thk @eschwellinger @sheberle .
Last updated: 2025-09-08

Post by ph0010421 on TCP/IP client ^{CODESYS Forge talk (Post)}
Hello TCIS_Send needs to be longer than 4 bytes because idata is 28 bytes long. There may be other ways, but I would make a UNION with string/array of bytes. Write your STRING into the AsString part then copy the AsBytes part into TCIS_Send (Elements [3] to [30]) then 252 would be in [31] (I've assumed the idata is always the same length)
Last updated: 2023-12-19

Post by eschwellinger on New Ladder Diagram conversion does not work due to missing features ^{CODESYS Forge talk (Post)}
The "remove unused" parameters have been added to 1.0 version as well as the "manual" removal of pins... also allowed "empty" inputs for blocks is in and the compile error described there should no longer occurs. Drag drop of variables is not yet implemented and I don't think the double-click feature yet either.
Last updated: 2024-01-29

Post by nima-khajehali on Data Transferring between 2 PLCs in a same PC ^{CODESYS Forge talk (Post)}
Hi Guys, I want to simulate the data exchange between 2 soft PLCs on the same PC. We are trying to simulate the process and we could not see the desired result. What should I do to pass all data between these 2 PLC's correctly ? Please see attached
Last updated: 2024-02-05

Post by smartcoco on Dynamic object release issues ^{CODESYS Forge talk (Post)}
Dear, When I use "__NEW" to dynamically create the object "Object_1", and assign this object "Object_1" to another object "Object_2". At this point, I use "DELETE" to release the object from "Object_2". At this time, I cannot judge whether the object has been released normally through "Object_1" (in fact, the object has been released theoretically). Thanks for you help.
Last updated: 2024-03-01

Post by mp9876 on Attempting customizing menus fails in LADDER environment; due to free CODESYS version ? ^{CODESYS Forge talk (Post)}
That definitely does the job with the Ladder Logic Diagram type; fully equipped toolbox. Just starting with Codesys and was following programming steps which explains the choice of ladder I had picked. Thanks for the tip and have a good one! Cheers!
Last updated: 2024-03-14

Sort by relevance or date