Post by tomast on Codesys and Siemens SINAMICS 20 modbus RTU "Response CRC Fail" ^{CODESYS Forge talk (Post)}
Hi everyone, I'm currently working on a project involving the control of 5 VFDs via Modbus RTU, this time using the WAGO 750-8212 CPU. So far, I've managed to make progress, but I've encountered an issue. While I can successfully read and write to all the registers I need, I consistently encounter a "Response CRC Fail" error when attempting to write the value 1151 to the STW register at address 40100. I'm able to set the frequency via register 40101 and adjust all other parameters using different registers. Setting STW to 1150 results in the drive ready boolean from the ZSW-bit being received instantly. However, the moment I attempt to send 1151 to register 40100, I immediately receive the "Response CRC Fail" error for all channels. I've also attempted to use combined control, employing Modbus for frequency control and starting from a digital input. Everything seems to function properly until I send the start command to the VFD. Interestingly, I consistently encounter the same error the moment I send the start command, regardless of whether I use register 40006 (high) or 40100 (1151). Could someone please assist me in resolving this issue?
Last updated: 2024-03-21

Post by andrea199403 on Assigning Modbus addresses to a structure in a dynamic way ^{CODESYS Forge talk (Post)}
Hello everyone, I am new to this forum and I am also new to Codesys programming. My problem is this: I have a STRUCT of 64 bool and 30 real, this STRUCT is assigned in the programme 9 times. Now I need to communicate with an HMI via Modbus and I have defined the slave device and created the holding registers for communication. I would like to declare the first call of the STRUCT on the Modbus registers %QX2000.0 to %QX2007.7 for the booleans and on the registers %QW1004 to %QW1034 for the real registers. That said, I would like to change an index and set an offset of 100 bytes for the calls of the other 8 assignments, so that the result is: %QX2100.0 to %QX2107.7 for the booleans and on the %QW1104 to %QW1134 registers for the Real registers, etc. Is there a way to declare this? Thank you very much.
Last updated: 2025-10-21

Post by muhq on Profinet connection to Siemens CP343-1 Lean (IO-Device/Slave) ^{CODESYS Forge talk (Post)}
Hi, I am quite new to Codesys and I try to do a Profinet connection to an Siemens PLC (315-2DP) with CP343-1 Lean Modul. I already configured the Siemens PLC, exported the GSDML. Then I added a new project in Codesys, added following moduls: - Ethernet - PN_Controller - Imported Profinet Device via GSDML importer When I start the programm everything looks fine but I always get the message "Stopped Profinet" and no data is available This is only for a small test. Therefore I start to do that on a Windows 10 with Development System. Later I will try to realize this on Raspberry. Ethernet Adapter is configured (192.168.1.1 / 24) Firewall deactivated WinPCap is installed S7-Station seems to be found ('fuadazenzitest') Can please somebody help me?
Last updated: 2023-08-26

Post by simotion on Pointer to Softmotion axis ^{CODESYS Forge talk (Post)}
In my projet I use Softmotion. There are several Softmotion axis (type SM_Drive_Virtual). In the Global Variable List I have an array of pointers to the adress of the Axis. Axis : ARRAY[1..iMaxCntAxes] OF POINTER TO AXIS_REF_SM3 := ADR(AX01_Axis), // [1 ADR(AX02_Axis), // [2] This works, but when compiling I get the message : . [WARNING] E3D: GVL Device: PLC Logic: Application: C0564: A reference to uninitialized variable AX01_Axis is used for initialization of Axis. Accessing the uninitialized variable may result in unexpected behavior. [WARNING] E3D: GVL Device: PLC Logic: Application: C0564: A reference to uninitialized variable AX02_Axis is used for initialization of Axis. Accessing the uninitialized variable may result in unexpected behavior. Is there a way when initializing to force the hardware (softmotion axis) to first initialize and then the Global Variable List?
Last updated: 2023-10-25

Post by andre-luis on Check if Codesys runtime is on 'Running' or 'Stopped' state? ^{CODESYS Forge talk (Post)}
Hi there, I'm running the Codesys runtime on Windows 64 and I need to know if it is on "Running" or "Stopped" state just after a system crash. The following commands works perfectly well to (re)start it... net stop “CODESYS Control Win V3 - x64" net start “CODESYS Control Win V3 - x64" ...however I'm unable to determine when it is required to be call; I mean, by checking the System Tray icon, it is possible to know if it is on "Stopped" state, but I wanted to run a .BAT command to retrieve it. How can we do that?
Last updated: 2024-07-02

Post by vamsi on How to configure gateway for programming RPi 2B using Codesys ^{CODESYS Forge talk (Post)}
I am using a Raspberry Pi 2B. Installed Codesys V3.5.20.1 64-bit and installed 'CODESYS Control for Raspberry PI 4.12.0.0' I am able to install the packages using the 'Update Raspberry Pi' option, but when I try to log into the RPi, in the Device tab it says 'Sacn fail. Please checl that the gateway is running and that its settings are correct'. My setup looks like this. I connected my RPi to my company LAN and also my laptop to company LAN (using HP Docking station). This setup worked when I installed 'CODESYS Control for Raspberry PI', but now I donot know how to configure the gateway. Could anyone please help me in finding what I have to enter in the gateway configuration? Thanks, Vamsi.
Last updated: 2024-07-10

Post by yoeri on Refresh visulization realtime ^{CODESYS Forge talk (Post)}
Hi everyone, I need some help with displaying an image (test.png) on my device. Initially, showing the image is straightforward. However, I want to be able to update the image dynamically. My goal is to send updated files via FTP to the device, and have the display automatically show the latest version of the image. All images will be sent with the same name (e.g., test.png). Currently, I can see the updated image after sending it via FTP and performing a warm restart, but I'd like to achieve this in runtime, without having to restart the display or application. Does anyone have suggestions on how to implement this? Thanks in advance!
Last updated: 2024-10-21

Post by hyys12 on CODESYS 3.5 dicovery of PLC modules ^{CODESYS Forge talk (Post)}
I have a WAGO PLC, to which I am establishing a connection. Here I use the autodiscover to register the connected modules. Now, I have tested the in-/outputs of the different modules, to verify they are consistent with how they are physically connected to the PLC in regards to how CODESYS has numbered them. Will CODESYS always number the modules closest to the PLC itself lowest, and the one furthest away, the highest? I am rather new to the program, so I both hope my question makes sense, as well as not being completely obvious. Thanks!
Last updated: 2024-12-06

Post by tmarmy1 on Redundancy for RTE x64 - stuck in standalone ^{CODESYS Forge talk (Post)}
Sorry if this has been asked before, but I can't seem to locate a thread that leads me answers. I am running two RTE x64 softPLCs, one on the host machine and a second via a VM. I have managed to finally get both to a position that they see each other, but they are in standalone mode instead of an active/passive state for failover (image attached). Every attempt to sync via the button fails. There is probably some step or option that I have missed in my bumbling through this learning process, but for the life of me I can't seem to figure it out. Anyone got any suggestions what I need to look at to get this into an active/passive redundancy state?
Last updated: 2025-02-20

Post by peterkcontrols on TargetVisu started in windowed or not full screen ^{CODESYS Forge talk (Post)}
Hello, I am using Codesys on an industrial pc with a single monitor. I would also like to have a separate vision software running on the PC and would like to display it half screen. When I run the soft PLC the my visualization screen appears full screen, I would like to be able to set the size of the visualization screen so I can display other software on the monitor. Is it possible to set the width/height of the targetVisu? Anyone try something similar? I would like to avoid having to put it on a Virtual Machine. Thank you
Last updated: 2025-02-26

Post by matthew on High resolution displays with 150% scaling causes CodeSys IDE to be blurry ^{CODESYS Forge talk (Post)}
I have just upgraded my laptop which has a high res display 2560x1600 and I have to have scaling switch on at 150% but everything looks blurry and not crisp, It seems CodeSys IDE is the only software on my system to look this bad, if I switch to 100% it's crisp but way to small. From a bit of research this could be due to the use of old windows forms or something? I have found a temp workaround that sort of works but not great. You have to run CodeSys in compatibility mode and adjust the DPI settings, this works ok and the editor is clear and crisp again but the actual tool bars are small like running at 100% Anyone got any tips for running CodeSys on high res displays with scaling?
Last updated: 2025-03-03

Post by bingo on PLC Shell commands via ST Code ^{CODESYS Forge talk (Post)}
Suppose you need to switch PLC IP dynamically between 192.168.1.10\192.168.2.10, First, set PLC IP to 192.16.1.10. Create a PGVL with a flag ‘xUseSecondry’ xUseSecondry : bool ; create a function that use socket to update IP: FUNCTION fSwitchIP : bool VAR_INPUT useMainIP:bool; END_VAR --------------------------------CODE------ if useMainIP then SysSockSetIPAddress(‘0’, ‘192.168.1.10’); PGVL.xUseSecondry := 0; else SysSockSetIPAddress(‘0’, ‘192.168.2.10’); PGVL.xUseSecondry := 1; end_if Now, if during execution, you need to switch IP, call the function ‘fSwitchIP()’, Set input to 1 for main IP, 0 for secondary IP. In order to set secondary IP at startup, you can do the following: in your PLC_PRG add a flag: xInit : bool := 1 ; and the code: if xInit then if PGVL.xUseSecondry then fSwitchIP(0); end_if xInit := 0 ; end_if *Alternative way is to use system events.
Last updated: 2025-03-03

Post by manuknecht on Using an Axis of an Axis Group in Torque Conctrol ^{CODESYS Forge talk (Post)}
I don't seem to be able to use an axis, which is part of an Axis Group in torque control mode. I call the SMC_SetControllerMode FB to switch from position to torque control mode, followed by the SMC_SetTorque FB to set the desired torque. This works flawlessly for most axes, however if an axis is part of an axis group, switching the controller mode seems to work without any issues, but the desired torque is never set. SMC_SetTorque does not return an error, but fSetTorque of the axis is never changed. Disabling the axis group before does not change anything, but if I use MC_UngroupAllAxes before changing the controller mode, it all works as it should. Is there no way to control a single axis in torque control, if it is part of an axis group?
Last updated: 2025-07-17

Post by bruceae on Special Characters ^{CODESYS Forge talk (Post)}
Hello, I am fairly new to the codesys environment. Is there a reference chart that I can look at in order to write special character in a string? The Special characters that I need to inclue inside the string are as follows; Null Bell Carriage Return I have a TCP_Write command that I am sending to an external device. In order for that device to function properly it needs to see the string with the null and bell characters as the header, followed by the desired command, terminated with the carriage return. Any reference sheet or how to write this in the actual string would be greatly appreciated.
Last updated: 2025-08-26

Post by toby on Ethercat Servo Setup ^{CODESYS Forge talk (Post)}
Hi everyone, so a little update to this, I've come back to this project in the new year, and got it working. Yeah!, However, now with the new licensing setup, I need a new SoftMotion license, but it doesn't seem to be compatible with the previous Raspberry Pi SL license. Has anyone had any luck with Raspberry Pi and SoftMotion_Lite? Specifically the licensing of such? My customers new installation needs to be rebooted every 30min which is causing headaches! Another option is to not use the SoftMotion function blocks, and control the EtherCat amplifier directly, but I'm not sure how to do so. Does anyone have a specific example project of how to control a servo without the use of the SoftMotion function blocks? Thanks everyone for any assistance rendered. It's very much appreciated! Toby
Last updated: 2024-01-10

Post by idalu on Profinet PN_Controller Issue, Network Adapter ^{CODESYS Forge talk (Post)}
i have a problem with Profinet on my project. I'm using Codesys RTE 3.5.19.50. When i download program to controller the ethernet is ok, PN_Controller is ok but every device i'm trying to connect is red with error "DCP no RealStationName". When i'm trying to Scan for Devices on PN_Controller there are no devices found. I have installed Codesys driver CmpEt1000Drv to my network adapter (i'm sure it is right intel pro 1000 model). I have noticed that when i installed codesys driver i'm no longer able to ping this network adapter (i can ping it when intel driver is installed). On my previous projects with runetimes i can ping it even with codesys driver installed. I have also tried to do downgrade of everything to version 3.5.19.20 and it not helped.
Last updated: 2024-01-17

Post by tokamk on Dynamic setting of the modbus tcp/ip slave ip address ^{CODESYS Forge talk (Post)}
Hello, I'm working on a project which includes Panel-PC which communicates with a PLC through Modbus TCP/IP. On the PLC I have a CODESYS code which has Modbus slave objects. The Modbus slave objects have to have manually set IP address in order for them to work properly and the Ip address has to be the PC-Panels's IP. This project is going to a customer and they're using their own IP address realm. So, my question is that is it possible to configure these slaves in some other way, so that the customer doesn't need to modify the CODESYS project? I was thinking that would it be possible to set the IP address of these slaves from external source?
Last updated: 2024-02-15

Post by nilesh on Request for Assistance with Online Logic Changes in PLC System using Codesys ^{CODESYS Forge talk (Post)}
Dear Sir, We are writing to seek guidance regarding our current situation with the Opto 22 Groov EPIC PR1 PLC system. Over the past year, we have successfully downloaded and implemented logic using Codesys, and the PLC has been operational without issues. However, we now require minor modifications to the logic. Despite attempting to upload the modified logic, we are unable to see the "online change" option, prompting us to consider a direct logic download. Our concern is that during this process, certain digital outputs or analog outputs might momentarily disrupt operations, which is unacceptable given the system's continuous 24x7 operation. We have explored online changes in other PLC systems, but due to the absence of the last downloaded backup, we are unable to proceed confidently.
Last updated: 2024-03-01

Post by vernon-laurence on EtherCAT fieldbus ^{CODESYS Forge talk (Post)}
The simplest way to do this would be to add a bus coupler dedicated to the expansion IO. The EtherCAT network does not fault when modules connected to the expander are not present. In the image below, nothing below the red line is present in the network - with the network working correctly. In your "base" project, simply include all of the possible modules, and then plug them in as you add pumps to the system. I would also highly recommend against the use of direct addressing. There are other methods to accomplish this, including using the "Optional" checkbox for modules and explicitly addressing them. Although, this would require more upfront work to design the network, and some additional work each time modules were added. https://content.helpme-codesys.com/en/CODESYS%20EtherCAT/_ecat_edt_slave_slave.html
Last updated: 2024-04-09

Post by danwoodlock on Rpi zero w lost license after 4.11 update ^{CODESYS Forge talk (Post)}
Hello all, Encountered an issue with my zero which seems to have happened after the 4.11 update. It now runs in demo mode (2hr) and I am trying to see what the appropriate steps are prior to contacting codesys directly. Background: I recently did a fresh install of w11 on my pc, so it seems "c:\ProgramData\CODESYS\Licenses\" only has information related to my pi5, which I licensed just this past Friday. I have all my license documentation about my rpi zero as far as the emails received, but when I try to claim using the ticket number it says its already been used, or something to that effect, which it was. Currently trying to perform device license reader, which is taking some time.
Last updated: 2024-04-14

Post by bjarne-pagaard on Codesys v3.5 Sint to byte ^{CODESYS Forge talk (Post)}
Hi A SINT is a short (signed) integer. It is already only 1 byte - so you should have no problem casting it to a byte like so: bMyByte := TO_BYTE(sintMyShortInt); If you have a regular INT you want to put in 2 bytes - there are a lot of ways you can do this. A Union is certainly one of them. You could have a union with 2 memebers: An array of 2 bytes as one member, and an integer value as another member. Another way would be to look at MEMCPY to put the value into your CAN-message. .. or create a function to take your input value as input, and giving you 2 individual bytes as output. This could be handy if you need to change the byte-order. Integer data types: https://help.codesys.com/webapp/_cds_datatype_integer;product=codesys;version=3.5.17.0 -Bjarne
Last updated: 2024-04-24

Post by peterned on CNC - system goes to X=0 Y=0 before CNC file execution starts, how to avoid that? ^{CODESYS Forge talk (Post)}
Hi, I have a XY system and use a CNC file to move it. Everything works OK, except for the following: when CNC execution starts, the system rushes at high speed to (X=0, Y=0) point, and only then goes to the first line of the CNC file. If one of the axes is near 0, the system jumps and immediately stops with an error. In the CNC file settings (screenshot attached) I specified low default values for speed/acceleration and a start position different from 0,0 - but all that is ignored. Any idea how to avoid that move to 0,0 ? Thanks.
Last updated: 2024-04-26

Post by salvadegianluca on SysPlcCtrl23 and C0338: The library 'cmperrors interfaces, 3.5.5.0 (system)' is supported just in 32 bit applications ^{CODESYS Forge talk (Post)}
Good afternoon to everyone; I'm stuck with this error and I don't know how to get out from it... I tried several time googling for alternative systems to control the PLC applications and resets but without success. I would like to realize the possibility to reset the CPU and to start/stop the applications as it was possible with the SysPlcCtrl23, but this library is no longer supported in 64 bit systems and it seems due to the cmperrors interfaces sub library that was included in the above said one. Someone found a work around for this issue?
Last updated: 2024-06-14

Post by salvadegianluca on SysPlcCtrl23 and C0338: The library 'cmperrors interfaces, 3.5.5.0 (system)' is supported just in 32 bit applications ^{CODESYS Forge talk (Post)}
Good afternoon to everyone; I'm stuck with this error and I don't know how to get out from it... I tried several time googling for alternative systems to control the PLC applications and resets but without success. I would like to realize the possibility to reset the CPU and to start/stop the applications as it was possible with the SysPlcCtrl23, but this library is no longer supported in 64 bit systems and it seems due to the cmperrors interfaces sub library that was included in the above said one. Someone found a work around for this issue?
Last updated: 2024-06-14

Post by salvadegianluca on SysPlcCtrl23 and C0338: The library 'cmperrors interfaces, 3.5.5.0 (system)' is supported just in 32 bit applications ^{CODESYS Forge talk (Post)}
Good afternoon to everyone; I'm stuck with this error and I don't know how to get out from it... I tried several time googling for alternative systems to control the PLC applications and resets but without success. I would like to realize the possibility to reset the CPU and to start/stop the applications as it was possible with the SysPlcCtrl23, but this library is no longer supported in 64 bit systems and it seems due to the cmperrors interfaces sub library that was included in the above said one. Someone found a work around for this issue?
Last updated: 2024-06-14

Sort by relevance or date