Post by jvfred on CodesysHMI.exe: Start Error
CODESYS Forge
talk
(Post)
I have used Codesys HMI SL on several projects. Today I turned my PC on to start building another project and received the following error message when I tried to start my device: "CodesysHMI.exe: Start Error One of the following licenses is required: CodeMeter 101597:13 Failure reason: CmContainer Entry not found, Error 200 CodeMeterAct 5000304:13 Failure reasons: CmContainer Entry not found, Error 200" I have tried reloading HMI SL and even updated to the current version with no success. I am using HMI SL version V3.5.20.10. Any help would be greatly appreciated.
Last updated: 2024-11-01
Post by jvfred on CodesysHMI.exe: Start Error
CODESYS Forge
talk
(Post)
I have used Codesys HMI SL on several projects. Today I turned my PC on to start building another project and received the following error message when I tried to start my device: "CodesysHMI.exe: Start Error One of the following licenses is required: CodeMeter 101597:13 Failure reason: CmContainer Entry not found, Error 200 CodeMeterAct 5000304:13 Failure reasons: CmContainer Entry not found, Error 200" I have tried reloading HMI SL and even updated to the current version with no success. I am using HMI SL version V3.5.20.10. Any help would be greatly appreciated.
Last updated: 2024-11-01
Post by jddaigle on TargetVisu controls are incorrectly positioned
CODESYS Forge
talk
(Post)
Hello, I'm trying to run TargetVisu on my Linux IPC, and while it does work, the controls are misaligned compared to my WebVisu. Both visualizations are full-screen on a Debian 12 VM with a resolution of 1280x768. The WebVisu is running in Firefox. Are there any configuration I should adjust to ensure the controls align properly between the two? Any guidance or troubleshooting tips would be greatly appreciated! Thank you.
Last updated: 2024-11-03
Post by selim on Need help to get RS-485 signal in Cosesys .
CODESYS Forge
talk
(Post)
Hello Mr./Ms., I invested Raspberry Pi lot of time to get the output from the raspberry PI5. But, i did not get the signal. I use a raspberry pi 5> RS485 can hat > Modbus RTU, Industrial 8-ch analog acquisition module >weight transmitter jy-s60> S-load cell. I did not able to receive the signal from Modbus RTU to Raspberry PI5 where I use the RS 485 serial connection.
Last updated: 2024-12-01
Post by smartcoco on Request a dark mode for CODESYS
CODESYS Forge
talk
(Post)
CODESYS IDE is not a modern IDE. Its interface is ugly, its operation is not user-friendly, its functions are lacking, its feedback is slow, and its development is not good enough. In fact, CODESYS is a helpless choice under the current situation. But this situation will not last long. For example, SIMATIC AX is a strong competitor of CODESYS, which is more open and inclusive.
Last updated: 2024-12-03
Post by paterad on Edge gateway
CODESYS Forge
talk
(Post)
Hello, I am struggling with Edge gateway to the automation server. It is not possible to establish the link. When I create the Edge in codesys and get it to Automation server, it is red, unable to connect. Scan fails. RPi 4B Runtime 4.13.0.0 Edge gateway 4.13.0.0 Codesys 3.5.2.40 Any idea what to chase? I have been using previous versions of edge gateway. Now I updated all to latest versions, failed. Frustrating.
Last updated: 2024-12-03
Post by amy123 on JSON Utilities ENUM to STRING
CODESYS Forge
talk
(Post)
Hello, Is it possible to get the string returned from the ENUM JSONType? I read that with regular enumerations you can add '{attribute 'to_string'}' and access it. However, this is from the compiled library, so I can not add that attribute. When I try to use TO_STRING(JSONType) it returns the integer as a string. Ex. jsonType :=TO_STRING(pJSONData^._aJSONData[i].eType); gives '8' instead of NONE Thanks!
Last updated: 2024-12-09
Post by pmanuele on Beckhoff AS1060 and EL7041 configuration
CODESYS Forge
talk
(Post)
Hello everyone, i'm having some problems commanding AS1060 step motor with EL7041 (rev22) drive. With motor i've also the incremental encoder (05.2420.1230.0200.5009). I can correctly move the motor in "Position controller" operating mode with the internal counter. The problems start when i set the Encoder in feedback type or i change the operating mode. Does anyone have experience with these two terminals and can give me some advice of main parameters to check or change? Thanks everyone
Last updated: 2024-12-11
Post by paulpotat on Can't find the safety manual in the documentation
CODESYS Forge
talk
(Post)
Hello, I was browsing the "CODESYS Virtual Safe Control for Linux SL" documentation page, and it says the following : For more information about the development of safety-critical applications with CODESYS, see: * Safety Manual H1 β SafetyManual.pdf, which is stored in the directory ../<user>/CODESYS Virtual Safe Control Linux SL/Delivery/Manuals</user> What does this path refers to ? I can't find it in CODESYS installation directories. Best regards
Last updated: 2025-01-23
Post by mubeta on Profibus DP master with EL6731 and automatic restart of slaves
CODESYS Forge
talk
(Post)
The problem is looking for a bug somewhere in CoDeSys in that, when the slave returns, the cyclic data exchange resumes, but the diagnostics do not update and the node continues to resulting off-line. it is not a problem with the PB master, but with its 3S/CoDeSys management. CoDeSys 3.5.19.20 runtime. Any ideas on how to fix it? Thank you.
Last updated: 2025-02-03
Post by dogulas on Removing a symbol from the IEC Symbols Editor grid
CODESYS Forge
talk
(Post)
In the CODESYS IDE I have several symbols defined and I have IEC Symbol Publishing installed. On the IEC Symbol Publishing window and under the IEC Symbols Editor tab, I have dragged symbols from the tree on the left to the grid on the right. All this works fine. Now I want to remove one of the symbols from the grid on the right and I cannot see any way to do this. How can I remove a symbol from the grid on the right once I've added it?
Last updated: 2025-02-07
To search for an exact phrase, put it in quotes. Example: "getting started docs"
To exclude a word or phrase, put a dash in front of it. Example: docs -help
To search on specific fields, use these field names instead of a general text search. You can group with AND or OR.