Post by aliazzz on Unable to deploy Virtual Control SL on ARM64 (Raspberry Pi5) ^{CODESYS Forge talk (Post)}
An interesting remark for CODESYS Support. I found this after looking through the Runtime Deploy Tool messages when I connect to an AMD64 architecture Successfully Connected to Target ( {MyIP} - AMD64 ) when I connect to an ARM64 architecture (Raspberry Pi5) Successfully Connected to Target ( {MyIP} - ) As clearly seen in the attached .png, the AMD64 target is detected, while the ARM64 target architecture is not detected (displayed). I assume that this is the reason why the pulldown menu isn't populated correctly.
Last updated: 2024-07-28

Post by micik on ERR_OK not recognized ^{CODESYS Forge talk (Post)}
Hello, if I try to use ERR_Ok in my code to check whether the file is open correctly or not, I get an error "Identifier ERR_OK not recognized", I can use plain 0 (zero) instead. But in general, is this a proper way to check for success of file operation since the 4th parameter is a poinmter to RTS_IEC_RESULT, and normally I would expect this to be used somehow. _hFile := SysFileOpen(_sFileName, am:=SysFile.ACCESS_MODE.AM_WRITE, ADR(_result)); IF _result <> 0 THEN udDiag := 100; RETURN;
Last updated: 2024-08-17

Post by richiemuia on Static Analysis, Loading Files via script. ^{CODESYS Forge talk (Post)}
I've seen that you can use cmds like below to run SA from scripts. system.commands["staticanalysis", "run"].execute() But I would like to run different SA configuration files to create separate logs and cant find anywhere in the scripting engine if this is supported. This stems from if I turn on everything, SA stops reporting issues in the message log when the list gets over 600ish issues. Once we have done an initial clean up of code this wont be an issue, but I'm trying to get a baseline to track improvement.
Last updated: 2024-08-21

Post by richiemuia on Static Analysis, Loading Files via script. ^{CODESYS Forge talk (Post)}
I've seen that you can use cmds like below to run SA from scripts. system.commands["staticanalysis", "run"].execute() But I would like to run different SA configuration files to create separate logs and cant find anywhere in the scripting engine if this is supported. This stems from if I turn on everything, SA stops reporting issues in the message log when the list gets over 600ish issues. Once we have done an initial clean up of code this wont be an issue, but I'm trying to get a baseline to track improvement.
Last updated: 2024-08-21

Post by durallymax on Access Variable Visu Dialog ^{CODESYS Forge talk (Post)}
Is there a way to access the variable in the called dialog? Example: Text Field element with PLC_PRG.myVar as Text variable. OnMouseClick configured to write variable with keypad pop-up. OnValueChanged configured to Execute ST RND(PLC_PRG.myVar,2); Rather than change myVar with each copy of this Text Field, is there a way to access whatever the configured text variable is? Generally try to stay away from ST in visu, but was curious regardless.
Last updated: 2024-11-14

Post by andre-luis on Device diagnosis ( EtherCAT IO card ) ^{CODESYS Forge talk (Post)}
Hi, In our project, it is not rare to have I/O cards issues. I wanted to have a way to check their statuses ( Eg. INIT, OP, PREOP, etc.. ) I was trying to use the GetDeviceDiagnosisInfo method from the IoConfig_Globals, but there is no info available on the Web with a simple example; does someone have a link to some tutorial or anything else ? Kind Regards, Andre.
Last updated: 2025-02-06

Post by trusty-squire on AXIS Rollover ^{CODESYS Forge talk (Post)}
In that case, the best thing to do might be to track the offset in a separate variable of your logic, then when you provide target positions, make your target position use the tracked offset as below: ActualTargetPosition := (TargetPosition + MyOffset) MOD 360; Although, upon further reflection, you'll still have the same cycle time issues. You might be able to break your code into multiple tasks to reduce the cycle time, or use an Event task to capture the offset position?
Last updated: 2025-03-12

Post by johnbomb on Ignore Dependencies When Loading Package? ^{CODESYS Forge talk (Post)}
I'm trying to load a .package into Codesys 3.5.21, but the package is intended to only work with Codesys 3.5.18.0 and is configured with dependencies on the specific versions of other packages included with 3.5.18.0, and 21 has newer versions so the package will not install. I would like to install the package anyway to try and get things working on a newer Codesys version, since for some reason the installer for .18 errors out and doesn't fully work in my environment, but .21 seems to work fine.
Last updated: 2025-04-01

Post by arwie on Use MC_Home without enabling the drive for homing method 35 ^{CODESYS Forge talk (Post)}
Is it possible to use MC_Home without enabling the drive (MC_Power)? On the drive the homing method 35 (Homing on current position) has to be executed. The drive has to stay disabled due to safety. This is explicitly allowed by the drive. Unfortunately MC_Home reports the error SMC_REGULATOR_OR_START_NOT_SET when executed. Are there other options to start homing, if not with MC_Home?
Last updated: 2025-06-25

Post by patrick on Version 3.5.19.40 probleme bei FUN mit _to_ im Name ^{CODESYS Forge talk (Post)}
Ich bin leider auch über den Fehler gestolpert, aber selbst in Version 3.5.19.50 ist dieser noch enthalten. Bis 3.5.19.20 kann ich meine Programme noch nutzen. Ab 3.5.19.30 ist der Fehler anscheinend vorhanden. Ich habe leider auch schon einen Haufen Programme mit meiner Library erstellt, somit wäre ein umbenennen nur mit sehr viel aufwand möglich.
Last updated: 2024-01-02

Post by eschwellinger on Bibliothek: floatingpointutils ^{CODESYS Forge talk (Post)}
naja die compiled library hast du ja - du hast halt eine exception - und dann wirst du gefragt ob du das ganze Debuggen willst. Die offene Bibliothek wirst du nicht bekommen - daher würde ich so vorgehen: Dein Projekt hier mal anhängen so das man mal draufschauen was du genau aufrufst und wie.
Last updated: 2024-10-18

Post by jeroenaero on CodeSys Raspberry pi I2C driver not found ^{CODESYS Forge talk (Post)}
yes i took the library from another forum: https://forge.codesys.com/forge/talk/Runtime/thread/f1400b71b6/, it is made for the ads1115 but the ads1015 is almost the same device with same adresses i only changed the divide value of the analog value, because thats the only difference between the ads1115 and ads1015.
Last updated: 2024-11-07

Post by lbouchard on CANOpen SIL2 error: UNSAFESTACK_NOT_OPERATIONAL ^{CODESYS Forge talk (Post)}
Hello, Working in 3.5 SP11 32 bit and using the 3S CANopenSafety Slave 3.5.11.0 library on an IFM CR711S. The 3SCSSD.CANOpenDevicesSIL2 function block keeps throwing "UNSAFESTACK_NOT_OPERATIONAL" Additionally, the Status of the device gives "There was an error accessing an I/O parameter". Any ideas on where my issues may lay? I have not found any good documentation that would explain the issue.
Last updated: 2025-05-23

Post by garyl on Comments in arrays and assigning RST coil's to 600 outputs ^{CODESYS Forge talk (Post)}
Hello all, im working on a project that requires me to convert an old automation direct DirectSoft PLC d2-250-1. One of the problems im encountering is that all of the comments are attached to members of the different addresses. When i convert the addresses (1777 "C" registers, 777 X registers, and 20,0000 V registers) im running into difficulties keeping the inputs/outputs correct since they are missing documentation. Is there a good way to retain the comments of the indexes in the array? Secondly, initially i was declaring the "C" and "V" addresses individually and this worked to retain the comments as to which register did what, however i ran into a problem when one rung reset (or set to 0) approximately 600 C Addresses. Since each tag is separately declared this proved to be nearly impossible without a literal wall of code that attempted to crash the program. So i converted all of the registers (C,X,Y,V) into separate structs, declared them as arrays and pointed all of the original call outs in the program to the newly defined structs. However i have now lost comments and the program is very hard to follow. Thanks for any help with this issue.
Last updated: 2023-08-31

Post by tomast on Codesys and Siemens SINAMICS 20 modbus RTU "Response CRC Fail" ^{CODESYS Forge talk (Post)}
Hi everyone, I'm currently working on a project involving the control of 5 VFDs via Modbus RTU, this time using the WAGO 750-8212 CPU. So far, I've managed to make progress, but I've encountered an issue. While I can successfully read and write to all the registers I need, I consistently encounter a "Response CRC Fail" error when attempting to write the value 1151 to the STW register at address 40100. I'm able to set the frequency via register 40101 and adjust all other parameters using different registers. Setting STW to 1150 results in the drive ready boolean from the ZSW-bit being received instantly. However, the moment I attempt to send 1151 to register 40100, I immediately receive the "Response CRC Fail" error for all channels. I've also attempted to use combined control, employing Modbus for frequency control and starting from a digital input. Everything seems to function properly until I send the start command to the VFD. Interestingly, I consistently encounter the same error the moment I send the start command, regardless of whether I use register 40006 (high) or 40100 (1151). Could someone please assist me in resolving this issue?
Last updated: 2024-03-21

Post by xnoop on MBTCP Slave configuration ^{CODESYS Forge talk (Post)}
Hello, I use Codesys 3.5 SP18 Patch 4 (64 bit) My Codesys project is composed of several dozen of Modbus TCP Slaves. I want to configure each of them by define : - Modbus TCP Slave Configuration : Name, IPAddress, port - Channels - Mapping I can't afford to configure manually and I need to find automatic way What possibilities does the Codesys offer? 1. I know it possible to use python script to create Modbus TCP Master and Slave. But I don't find anyway to create Channels and Mapping through the API 2. I 've tested to set mapping with file.csv on a Modbus Tcp Slave, but no way to import channels definition from file 3. I 've tried to use PLCOpenXml file. For example I 've create a project with an Ethernet device. I've exported it in PlcOpenXml file. After delete the Ethernet device, I've imported the PlcOpenXml file without success. I've tried the same by creating Modbus TCP Slave. Could you help me to find to good way ? Thanks
Last updated: 2024-06-19

Post by grant32 on RAMP_REAL FB is retaining my output value when i try to re use the FB ^{CODESYS Forge talk (Post)}
Hello, I'm relatively new to PLC programming. I am trying to creat a ramp down function, I have an example here of what I am using. I can get the function to work, the issue is that the OUT (variable3) value is being held by the FB so after I use it once it no longer works. In this example i set variable3 to 100 and the rest is as seen, over the course of a minute it ramped down to 10 (as desired). But when I deenergize TEST_START, set variable3 back to 100, and then re-energize TEST_START it immediately jumps back to the previously held value 10. The reset on this block just pauses the function and holds the last OUT. In my case I will need the function to start OUT at a set value, ramp down to the IN (variable2) value, and then accept a new OUT value to ramp down next time the block is energized. Hopefully this made sense, if anyone has any advice that would be awesome!
Last updated: 2024-07-29

Post by to-ke on Errors with VisuUserManagement library ^{CODESYS Forge talk (Post)}
Hallo zusammen, hi all, ich habe den gleichen Fehler. Auf einem Raspberry Pi geht der Fehler weg, wenn ich alles bereinige und dann vollständig übersetze. Wenn das Projekt im Codesys Development System wieder neu geladen wird ist der Fehler aber wieder da. Mit eine Win V3 x64 PLC kann ich den Fehler nur unterbinden wenn ich auf der HMI das VUM_Login einbinde. Dieses brauche ich aber nicht, da ich die HMI für das User Management selbst gestaltet habe. Das funktioniert auch. I have the same error. On a Raspberry Pi the error goes away if I clean everything and then compile completely. When the project is reloaded in the Codesys Development System, the error returns. With a Win V3 x64 PLC I can only prevent the error if I integrate the VUM_Login on the HMI. But I don't need this because I designed the HMI for user management myself. That works too. Anyone have an idea to fix this problem. Many thanks
Last updated: 2024-07-09

Post by mgabryel on Problems with CAN 2.0 comunication on Wago PLC (Codesys 3.5) ^{CODESYS Forge talk (Post)}
Hello, I am trying to program CAN Bus comunication on WAGO PLC (more precisely on WAGO Touch Monitor model TP600). I am using for this purpose library "WagoAppCanLayer2" from Wago company. My IDE for programming this device is CODESYS V3.5 SP19 Patch 2 + (64-bit). My program is written in Structured text using function blocks from previously mentioned library. Here is code of this program: 1) Variables declarations: PROGRAM PLC_PRG VAR oOpenInterface : WagoAppCanLayer2.FbCanL2Open :=( udiBaudrate := 125000 ); xInterfaceIsOpen : BOOL; sInterfaceInfo : STRING; oReceive : WagoAppCanLayer2.FbCanRx29BitFrame :=( xBufferMode := FALSE, wCanId := 16#181 ); xRecv : BOOL; sReceiveInfo : STRING; oSend : WagoAppCanLayer2.FbCanTx29BitFrame :=( dwCanId := 16#100, //was 16#201 xRtrFrame := FALSE ); xSend : BOOL; sSendInfo : STRING; oCanDiag : WagoAppCanLayer2.FbCanErrorInfo; xRst : BOOL; aSendData : ARRAY [1..8] OF BYTE; bSendLen : BYTE; TON_0 : TON; TON_1 : TON; END_VAR 2) Program body: oOpenInterface( xEnable := NOT xInterfaceIsOpen, I_Port := IoConfig_Globals.WAGO_CAN_LAYER2_DEVICE ); sInterfaceInfo := oOpenInterface.oStatus.GetDescription(); xInterfaceIsOpen S= oOpenInterface.xValid AND NOT oOpenInterface.xError; oReceive( xEnable := xInterfaceIsOpen, I_Port := IoConfig_Globals.WAGO_CAN_LAYER2_DEVICE, xRxTrigger := xRecv ); sReceiveInfo := oReceive.oStatus.GetDescription(); IF NOT xRecv THEN IF oReceive.bRxNBytes > 0 THEN oReceive.aRxBuffer[1]; oReceive.aRxBuffer[2]; oReceive.aRxBuffer[3]; oReceive.aRxBuffer[4]; oReceive.aRxBuffer[5]; oReceive.aRxBuffer[6]; oReceive.aRxBuffer[7]; oReceive.aRxBuffer[8]; END_IF xRecv := TRUE; END_IF aSendData[1] := 224; aSendData[2] := 13; aSendData[3] := 14; aSendData[4] := 15; aSendData[5] := 222; aSendData[6] := 13; aSendData[7] := 14; aSendData[8] := 15; bSendLen := 8; TON_0(IN:= NOT TON_1.Q, PT:= T#2S , Q=>xSend, ET=> ); TON_1(IN:= TON_0.Q, PT:= T#2S , Q=>, ET=> ); oSend( xEnable := xInterfaceIsOpen, I_Port := IoConfig_Globals.WAGO_CAN_LAYER2_DEVICE, aTxBuffer := aSendData, bTxNBytes := bSendLen, xTxTrigger := xSend ); sSendInfo := oSend.oStatus.GetDescription(); oCanDiag( xEnable := TRUE, I_Port := IoConfig_Globals.WAGO_CAN_LAYER2_DEVICE, xTriggerResetCounter := xRst, xValid=> , xError=> , oStatus=> , wBusState=> , wBusDiag=> , uiRxOverflowsL2=> , uiTxOverflowsL2=> , uiRxOverflows=> , uiMsgTimeouts=> , uiBusOffs=> , uiBusWarnings=> ); Program first opens comunication on CAN 2 device and then periodically try send one CAN data frame. After starting program CAN 2 interface is properly open. The xSend variable is toggling with period 2s. When program sends data an "Tx overflow" error appears. When I am watching CAN_H line on DSub 9 socket i am not able to see proper CAN frames - see screenshot attached to this message. Could somebody help me determine what is wrong with this program. Best regards
Last updated: 2024-08-02

Post by muhq on Profinet connection to Siemens CP343-1 Lean (IO-Device/Slave) ^{CODESYS Forge talk (Post)}
Hi, I am quite new to Codesys and I try to do a Profinet connection to an Siemens PLC (315-2DP) with CP343-1 Lean Modul. I already configured the Siemens PLC, exported the GSDML. Then I added a new project in Codesys, added following moduls: - Ethernet - PN_Controller - Imported Profinet Device via GSDML importer When I start the programm everything looks fine but I always get the message "Stopped Profinet" and no data is available This is only for a small test. Therefore I start to do that on a Windows 10 with Development System. Later I will try to realize this on Raspberry. Ethernet Adapter is configured (192.168.1.1 / 24) Firewall deactivated WinPCap is installed S7-Station seems to be found ('fuadazenzitest') Can please somebody help me?
Last updated: 2023-08-26

Post by simotion on Pointer to Softmotion axis ^{CODESYS Forge talk (Post)}
In my projet I use Softmotion. There are several Softmotion axis (type SM_Drive_Virtual). In the Global Variable List I have an array of pointers to the adress of the Axis. Axis : ARRAY[1..iMaxCntAxes] OF POINTER TO AXIS_REF_SM3 := ADR(AX01_Axis), // [1 ADR(AX02_Axis), // [2] This works, but when compiling I get the message : . [WARNING] E3D: GVL Device: PLC Logic: Application: C0564: A reference to uninitialized variable AX01_Axis is used for initialization of Axis. Accessing the uninitialized variable may result in unexpected behavior. [WARNING] E3D: GVL Device: PLC Logic: Application: C0564: A reference to uninitialized variable AX02_Axis is used for initialization of Axis. Accessing the uninitialized variable may result in unexpected behavior. Is there a way when initializing to force the hardware (softmotion axis) to first initialize and then the Global Variable List?
Last updated: 2023-10-25

Post by tokamk on Dynamic setting of the modbus tcp/ip slave ip address ^{CODESYS Forge talk (Post)}
Hello, I'm working on a project which includes Panel-PC which communicates with a PLC through Modbus TCP/IP. On the PLC I have a CODESYS code which has Modbus slave objects. The Modbus slave objects have to have manually set IP address in order for them to work properly and the Ip address has to be the PC-Panels's IP. This project is going to a customer and they're using their own IP address realm. So, my question is that is it possible to configure these slaves in some other way, so that the customer doesn't need to modify the CODESYS project? I was thinking that would it be possible to set the IP address of these slaves from external source?
Last updated: 2024-02-15

Post by vernon-laurence on EtherCAT fieldbus ^{CODESYS Forge talk (Post)}
The simplest way to do this would be to add a bus coupler dedicated to the expansion IO. The EtherCAT network does not fault when modules connected to the expander are not present. In the image below, nothing below the red line is present in the network - with the network working correctly. In your "base" project, simply include all of the possible modules, and then plug them in as you add pumps to the system. I would also highly recommend against the use of direct addressing. There are other methods to accomplish this, including using the "Optional" checkbox for modules and explicitly addressing them. Although, this would require more upfront work to design the network, and some additional work each time modules were added. https://content.helpme-codesys.com/en/CODESYS%20EtherCAT/_ecat_edt_slave_slave.html
Last updated: 2024-04-09

Post by danwoodlock on Rpi zero w lost license after 4.11 update ^{CODESYS Forge talk (Post)}
Hello all, Encountered an issue with my zero which seems to have happened after the 4.11 update. It now runs in demo mode (2hr) and I am trying to see what the appropriate steps are prior to contacting codesys directly. Background: I recently did a fresh install of w11 on my pc, so it seems "c:\ProgramData\CODESYS\Licenses\" only has information related to my pi5, which I licensed just this past Friday. I have all my license documentation about my rpi zero as far as the emails received, but when I try to claim using the ticket number it says its already been used, or something to that effect, which it was. Currently trying to perform device license reader, which is taking some time.
Last updated: 2024-04-14

Post by bjarne-pagaard on Codesys v3.5 Sint to byte ^{CODESYS Forge talk (Post)}
Hi A SINT is a short (signed) integer. It is already only 1 byte - so you should have no problem casting it to a byte like so: bMyByte := TO_BYTE(sintMyShortInt); If you have a regular INT you want to put in 2 bytes - there are a lot of ways you can do this. A Union is certainly one of them. You could have a union with 2 memebers: An array of 2 bytes as one member, and an integer value as another member. Another way would be to look at MEMCPY to put the value into your CAN-message. .. or create a function to take your input value as input, and giving you 2 individual bytes as output. This could be handy if you need to change the byte-order. Integer data types: https://help.codesys.com/webapp/_cds_datatype_integer;product=codesys;version=3.5.17.0 -Bjarne
Last updated: 2024-04-24

Sort by relevance or date