Post by mp9876 on Attempting customizing menus fails in LADDER environment; due to free CODESYS version ? ^{CODESYS Forge talk (Post)}
That definitely does the job with the Ladder Logic Diagram type; fully equipped toolbox. Just starting with Codesys and was following programming steps which explains the choice of ladder I had picked. Thanks for the tip and have a good one! Cheers!
Last updated: 2024-03-14

Post by k4zz on Static Code Analysis ^{CODESYS Forge talk (Post)}
I've already experimented with two methods, but unfortunately, they only function with projects of type *.project. Consequently, when executing: system.commands["staticanalysis", "run"].execute() For the 2nd Option: You'll need to ensure that in the Static Analysis Settings, the option "Perform static analysis automatically after compilation" is checked. # get Project values myProject = projects.primary # Creates an active application app = myProject.active_application # build Application and run static code analysis app.generate_code()
Last updated: 2024-03-15

Post by eschwellinger on connect IDE to plc that uses modem ppp ^{CODESYS Forge talk (Post)}
Which plc type is it? Easy connection is to install a Gateway on remote side - this is available for Windows and Linux devices Then just add a new Gateway in CODESYS (with the IP Adress of the remote device) -> then scan the plc via this new added Gateway
Last updated: 2024-05-21

Post by rjonker on codesys mqtt publish serialization ^{CODESYS Forge talk (Post)}
pbPayload is a pointer, which it expects to point at a STRING. If you point it at an address holding a different data type, it will just assume those bytes are part of a string and likely trundle along memory until it finds a null byte (0x00) that would normally signify the end of a string PublishMessage := BOOL_TO_STRING(boolVariable);
Last updated: 2024-06-05

Post by maxsus on Visu Frame-configuration___text will not work ^{CODESYS Forge talk (Post)}
Hello I have a problem with the Frame-configuration. In the picture below you can see that I set the Editor Type to variable. If it would be text it would work, but it wasnt variable anymore. Thanks for your time. Sorry, my codesys is in German.
Last updated: 2024-08-20

Post by maxsus on Visu Frame-configuration___text will not work ^{CODESYS Forge talk (Post)}
Hello I have a problem with the Frame-configuration. In the picture below you can see that I set the Editor Type to variable. If it would be text it would work, but it wasnt variable anymore. Thanks for your time. Sorry, my codesys is in German.
Last updated: 2024-08-20

Post by timvh on Configuring a 2's compliment ^{CODESYS Forge talk (Post)}
You could create a DUT of the Type Union and add an array of 2 bytes + an Int. Then write the byte values in the array of the Union and read the Int. Or VAR iInt : INT; byHigh : BYTE := 2#1111_1111; byLow : BYTE := 2#1111_1111; END_VAR iInt := TO_INT(byHigh*16#100 + byLow);
Last updated: 2024-09-28

Post by janber on REFERENCE TO in an array ^{CODESYS Forge talk (Post)}
Hi all, in the online help it written, that array of reference to data type is not possible. Ok... but if I create array of struct of reference to - everything works fine - please see the screenshots: and it works this way OK. Is it intention or error in compiler 3.5.18.20 and we should avoid it? Thanks a lot, Jan.
Last updated: 2024-10-14

Post by reinier-geers on Energie price ^{CODESYS Forge talk (Post)}
On a website i can get the energie price. But how does that work in codesys? There is a video of Rest client. But i can find the HTTP library. If i type on my browser : https://enever.nl/api/stroomprijs_vandaag.php?token=ANWB i get {"status":"true","data":"Please provide a valid API token. More information at https:\/\/enever.nl\/prijzenfeeds\/","code":"2"}
Last updated: 2024-12-03

Post by reinier-geers on Energie price ^{CODESYS Forge talk (Post)}
On a website i can get the energie price. But how does that work in codesys? There is a video of Rest client. But i can find the HTTP library. If i type on my browser : https://enever.nl/api/stroomprijs_vandaag.php?token=ANWB i get {"status":"true","data":"Please provide a valid API token. More information at https:\/\/enever.nl\/prijzenfeeds\/","code":"2"}
Last updated: 2024-12-03

Post by winki on Warning attribut no_assign ^{CODESYS Forge talk (Post)}
Hello, I have two warning on my code, and I would like to understand why. C0540: Attribut 'no_assign' missing for the 'FB_MOdbusReadHolding'. The type of the variable clientTcp is set to 'no_assign'. In this FB, I have done: clientTcp : ModbusFB.ClientTCP; clientRequest : ModbusFB.ClientRequestReadHoldingRegisters; The error comes from clientTcp : ModbusFB.ClientTCP; I am using ModbusFB 4.4.0.0. Thx a lot
Last updated: 2025-01-10

Post by winki on Warning attribut no_assign ^{CODESYS Forge talk (Post)}
Hello, I have two warning on my code, and I would like to understand why. C0540: Attribut 'no_assign' missing for the 'FB_MOdbusReadHolding'. The type of the variable clientTcp is set to 'no_assign'. In this FB, I have done: clientTcp : ModbusFB.ClientTCP; clientRequest : ModbusFB.ClientRequestReadHoldingRegisters; The error comes from clientTcp : ModbusFB.ClientTCP; I am using ModbusFB 4.4.0.0. Thx a lot
Last updated: 2025-01-10

Post by imdatatas on Problem with edge gateway config mode ^{CODESYS Forge talk (Post)}
I encountered the same problem. (Windows10 x64 single language OS). As @eschwellinger mentioned, I uninstalled the latest EdgeGateway version and installed version 3.5.20.0. Now, when I right-click and select "Allow Edge Gateway...", Config mode is activated without any error or warning window and I do not need to manually type [CmpEdgeGateway] for EdgeGateway version 3.5.20.0.
Last updated: 2025-02-04

Post by mubeta on UNION statement is not supported in the ethercat data exchange ^{CODESYS Forge talk (Post)}
Hi all, I am using a unionn statement for merge in integer data type some values that are received in byte from the i/o cards, but, using this simple and light technique, is not recognized by the ethercat data exchange and in fact the tags are not updated. In my opinion it's a very big bug.
Last updated: 2025-02-05

Post by eschwellinger on Codesys Network driver install for Codesys Control RTE x64 ^{CODESYS Forge talk (Post)}
Yes, either adding in the CODESYSContro_User.cfg because the driver will no longer appear in the list or type the name from the documentation in the configuration and when the gray check mark appears, the driver is also installed. It is just not selectable anymore.
Last updated: 2025-03-21

Post by davidmic on Struct Literal ^{CODESYS Forge talk (Post)}
Hi all I want to pass a struct into a function without declaring the struct in a VAR/END_VAR. Is this possible? I think this would be called a struct literal It would look something like this someFB.write(structArgument := MyStruct#(a := 1, b := 1.2), otherArgument := TRUE); With this struct declaration TYPE MyStruct : STRUCT a : INT; b : REAL; END_STRUCT END_TYPE
Last updated: 2025-03-28

Post by z870623 on About CPU Loading ^{CODESYS Forge talk (Post)}
I am running a runtime environment on an ARM A35 dual-core processor (1.5GHz) and have encountered some issues. The CPU load (both CPU0 and CPU1) occasionally spikes above 50% before returning to normal, and this happens around 2-3 times per minute. At the same time, I’ve noticed that the Max Cycle Time in the Codesys monitoring screen shows much worse performance compared to the A53 (1.2GHz), with nearly double the cycle time. The optimizations I have made so far are as follows: Set the CPU to performance mode. Isolated CPUs: CPU0 is dedicated to running Linux services and the runtime itself, while CPU1 runs the EtherCAT task and the MainTask. Despite CPU1 only running these two tasks, the utilization still increases above 50%, which I find unreasonable. Additionally, I performed tests using cyclictest both without and with the runtime running. The performance is shown in the following image: From the results, I believe the CPU performance should be fine, but I am unsure why the monitoring results are not as expected. The testing outcomes should ideally be as close as possible to the cyclictest results. Does anyone have related solutions to this issue?
Last updated: 2024-10-14

Post by duvanmoreno24 on Modbus writing on value change ^{CODESYS Forge talk (Post)}
Yes, I tried to do what you put in the first code. However, I have a problem with that and that is that the inputs must be declared with the type. I have many data types running in my code (real, int, uint, bool) and I can't put them in the same function, another thing is that I need to instantiate that function for everything I want to write to the slave. You put a for to 200 but it means that it has to be the same data type and inside the array, but I want to get them individually. I'm struggling to do it in a good and efficient way like wago's E-cockpit does. in the first screenshot you can see, you simply type in value, change the package of things you want to write in value change and it does everything by itself automatically, without comparing any old and new values and even less having the need to activate a bool. , it is perfect.
Last updated: 2024-04-03

Post by marek71 on Ambiguous use of name - CO136 ^{CODESYS Forge talk (Post)}
My PLC is WAGO PFC200 Firmware Revision 26. target After updating WAGO_Devices_and_Libraries with newer Firmware 27, CODESYS wants to update all libraries to new versions. I will only add that I did not update the Firmware in the PLC. After compiling the program, I received the following errors: ------ Build started: Application: Device.Application ------- Typify code... [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): FbSerialInterface_internal: C0136: Ambiguous use of name 'RTS_IEC_HANDLE' [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): FbSerialInterface_internal: C0136: Ambiguous use of name 'RTS_IEC_RESULT' [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): Initialize [FbSerialInterface_internal]: C0032: Cannot convert type 'Unknown type: 'RTS_INVALID_HANDLE'' to type 'POINTER TO BYTE' [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): Initialize [FbSerialInterface_internal]: C0136: Ambiguous use of name 'RTS_INVALID_HANDLE' [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): Initialize [FbSerialInterface_internal]: C0046: Identifier 'RTS_INVALID_HANDLE' not defined [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): comextra_is_tx_empty: C0136: Ambiguous use of name 'RTS_IEC_HANDLE' [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): comextra_get_line_state: C0136: Ambiguous use of name 'RTS_IEC_HANDLE' [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): comextra_is_line_available: C0136: Ambiguous use of name 'RTS_IEC_HANDLE' [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): COMSW_SET_MODE: C0136: Ambiguous use of name 'RTS_IEC_HANDLE' [ERROR] wagosyscom_internal_pfc, 1.0.2.5 (wago): comextra_set_line_state: C0136: Ambiguous use of name 'RTS_IEC_HANDLE' Compile complete -- 10 errors, 0 warnings Build complete -- 10 errors, 0 warnings : No download possible The problem was caused by the WagoSysPlainMem(WAGO) library in the original version 1.5.3.0 after updating to 1.5.3.1. After returning to version 1.5.3.0, the problems disappeared. Probably the version number of this library is responsible for supporting the appropriate Firmware Revision. Can anyone confirm or deny my suspicions?
Last updated: 2024-07-06

Post by janderson on Ethercat scan for devices not picking up EL7041 as a softmotion axis ^{CODESYS Forge talk (Post)}
it appears that the different revisions have different PDOs. I am currently trying to use the rev25. I have tried to use the rev24 (the device repository entry not from 'scan for devices') and i keep getting 'invalid output mapping' or 'invalid input mapping' in the ethercat log. I cant even get the bus to run from the device description that comes from 'scan for devices'...
Last updated: 2023-09-18

Post by janderson on Ethercat scan for devices not picking up EL7041 as a softmotion axis ^{CODESYS Forge talk (Post)}
it appears that the different revisions have different PDOs. I am currently trying to use the rev25. I have tried to use the rev24 (the device repository entry not from 'scan for devices') and i keep getting 'invalid output mapping' or 'invalid input mapping' in the ethercat log. I cant even get the bus to run from the device description that comes from 'scan for devices'...
Last updated: 2023-09-18

Post by albertisa on GPIO Konfiguration auf SK-AM64B ^{CODESYS Forge talk (Post)}
Hallo, seit einigen Tagen versuche ich erfolglos eine Ansteuerung der GPIOs des SK-AM64B Entwicklungsboards (Texas Instruments) über Codesys zu bewerkstelligen. Bei dem Versuch GPIOs anzusteuern, ohne die devdesc.xml bzw. den iodriver anzupassen, wird mir von Codesys die Fehlermeldung "Bus läuft nicht" (siehe Screenshot) angezeigt. Welche Vorgehensweise wird zur Konfiguration der IO empfohlen? Ist eine Anpassung der devdesc.xml und des IOdrivers notwendig? Wie wird am besten bei der Anpassung der genannten Dateien vorgegangen? Folgende Dokumentation ist mir bekannt, hat mir aber noch nicht weitergeholfen: https://forge.codesys.com/drv/io-drivers/doc/Generic/
Last updated: 2023-09-19

Post by vincentger on using ADS1115 ^{CODESYS Forge talk (Post)}
Any reason the ADS1115 wouldnt work with SP20.1 and Runtime 10.0.0.0 on the Raspberry Pi . Using Bullseye or Buster i run into the same issue: Libary and integration works in general as described above BUT i am seeing "bleeding" between the analog inputs . Specifically consecutive ones: So sometimes the raw from AI1 shows on AI2, AI2 on AI3, .. AI4 on AI1. Even with filtering i cant smoothen that out properly and i feel like something is wrong. Almost like the bus is stumbling over itself, or the request from Codesys to the device.
Last updated: 2024-10-28

Post by dkugler on Beckhoff EL6652-0010 with Codesys ^{CODESYS Forge talk (Post)}
we use successful for many years the KEB MFI terminal for Profinet, EtherCAT, Ethernet/IP,... You'll need a EtherCAT Coupler as "head" from KEB, Kendrion or Berghof. It's all the same board inside: https://www.kebamerica.com/products/ethercat-bus-coupler/ Or the coupler with 16Di/Do integrated: https://www.kebamerica.com/products/ethercat-digital-io-module/ last year I got a EK1100 with EL6731 Profibus treminal runnig. But it was a lot of reverse engineering and thinkering in Codesys and TwinCAT to be done, to get it up, fulfilling my needs. Good luck!
Last updated: 2025-03-25

Post by installwhat on Ethercat and profinet on together ^{CODESYS Forge talk (Post)}
I'm curious about the impact of having profinet and Ethercat (specifically softmotion so frame at start of task?) running together. Since it's advised to access the data from the bus task should have both profinet io and ethercat on the same task? Are there any implications around this one should be aware of especially since the frame at task start is just, so far as I'm aware, an ethercat thing? Thanks
Last updated: 2025-04-08

Sort by relevance or date