Post by bertus on Axis directions in CNC editor not using right-hand rule?
CODESYS Forge
talk
(Post)
Hello, Coming from robotics, I'm used to coordinate systems using the right-hand rule. But when I created below small NC program in the Codesys CNC editor, I noticed that the axis triad's Z-axis is flipped (see attached screenshot), resulting in left-hand rule. Is there a setting to change this? Or am I misunderstanding something in the CNC world? N000 G00 X0 Y0 N010 G01 X100 N020 G01 Y50 N030 G01 X0 N040 G01 Y0 N050 G01 Z25
Last updated: 2026-01-02
Post by axberry on CODESYS Control for Raspberry Pi 5 - "Hardware version or firmware version not supported" on Rev 1.1, persists across multiple runtime versions and OS images
CODESYS Forge
talk
(Post)
Hi, I'm trying to run CODESYS Control for Raspberry Pi SL on a Raspberry Pi 5, and the runtime consistently fails to start with the following error when launched manually: ooops... this runtime was built for RASPBERRYPI. Hardware version or firmware version not supported! (-18, 0x00000BB8, 0xFFFFFFFB) Hardware: Raspberry Pi 5 Model B Rev 1.1 Revision code: d04171 CPU: aarch64, BCM2712 Serial number is correctly exposed via /proc/cpuinfo and /proc/device-tree/serial-number /proc/device-tree/model correctly reports "Raspberry Pi 5 Model B" What I've tried (all resulting in the same error): CODESYS Control for Raspberry Pi SL 4.11.0.0 (SDK 3.5.19.61) β the version that introduced Pi 5 support CODESYS Control for Raspberry Pi SL 4.21.0.0 (SDK 3.5.22.20) β latest available Raspberry Pi OS Bookworm (64-bit) with kernel 6.12.93+rpt-rpi-2712 (June 2026 build) Fresh install on Raspberry Pi OS Bookworm (64-bit) with an older image from November 24, 2025 β same error, ruling out a kernel-version regression Bootloader/EEPROM confirmed up to date (rpi-eeprom-update reports "up to date") Clean purge and reinstall of the codesyscontrol package each time (verified via dpkg -l, no leftover files) Verified /etc/codesyscontrol/3S.dat correctly symlinks to /etc/codesyscontrol/3S_aarch64.dat The service starts (systemctl status briefly shows active (running) with a real PID under /opt/codesys/bin/codesyscontrol.bin), but crashes shortly after and the process disappears β port 11740 never opens. Since this happens identically across two different runtime versions and two different OS images (5+ months apart), it doesn't seem to be a kernel/firmware timing issue. Could this be specific to the Rev 1.1 board revision, or is there a known issue with the hardware detection logic in the SL runtime that I should be aware of? Happy to provide full debug logs (-d flag output) or journalctl output if useful. Thanks in advance!
Last updated: 2026-08-10
Post by dmb-fan on From target start Win OnScreenKeyboard
CODESYS Forge
talk
(Post)
Hi ! I am get crazy.... I try to start osk.exe from Visu or PLC. From Visu I can't load it, always error (It change from programm execute always to load receipe ..!?!?) From PLC always freeze of PLC, - I allowed the win service of the PLC the data exchange between desktop and service - I allowed in ..user.cfg [SysProcess] Command=AllowAll Shutdown with SysProcessExecuteCommand works, but 'osk.exe' or the complete path always crashed the system. And like always: No documentation. Just guessing. Or know somebody more and have a link for me? THANKS !
Last updated: 2026-10-27
Post by gseidel on Axis directions in CNC editor not using right-hand rule?
CODESYS Forge
talk
(Post)
Hi bertus, the coordinate systems used in SoftMotion CNC are all right-handed. The CNC editor uses isometric projection. This can be confusing, as in your example. The y-axis seems to point into the screen, away from the viewer. However, this is just an optical effect. If you turn on the (experimental) perspective projection (must be added to the CNC tool bar using tools->customize), you can see that the coordinate system is in fact right-handed. Best regards, Georg
Last updated: 2026-01-07
Post by srinidhi on Pilz PBRT Robot with CoDeSys
CODESYS Forge
talk
(Post)
If anyone here are working with robots and using Codesys to control it and implement tasks, Please let me know. I am currently in my Master thesis and i need some advice on this. We have Pilz Robot with Codesys and I am trying to proceed with certain tasks but have no documentation for it. Would be helpful if anyone of you can suggest and help connect with the right people.
Last updated: 2026-05-10
Post by luca03 on OPC UA information model into the Communication Manager
CODESYS Forge
talk
(Post)
Hello, unfortunately I am unable to load an OPC UA information model as a NodeSet2.xml file into the CODESYS Communication Manager. Importing via Tools -> OPC UA Information Model Repository still works, but when I try to load the model explicitly, CODESYS crashes without displaying an error message. Has anyone else encountered this problem, or does anyone have any suggestions? Thanks in advance
Last updated: 2026-08-22
Post by jgalaska on SMC_Trafo 6DOF Config Error
CODESYS Forge
talk
(Post)
Hello, Recently I was trying to run 6DOF robot in codesys via SMC_Trafo_ArticulatedRobot_6DOF, unfortunately no matter what parameters I tried, it always outputs InvalidConfig Error. I saw the same issue in a topic: https://forge.codesys.com/forge/talk/Motion/thread/16e1f0327f/ But if I understand correctly, the user solved it by developing his own version of this block. I wanted to know if it is a bug in the library (SM3_CNC 4.20.0.0) or am I doing something wrong? Can anyone confirm that they can use the FB without it reporing the Error? Kind regards,
Last updated: 2026-01-21
Post by zeljko2212 on Seeking a Code-Based Solution for EtherCAT Slave Dropout or Master Errors in Production (Beyond Software Hot Reset)
CODESYS Forge
talk
(Post)
PROGRAM RES_ECAT VAR xMP1: INT; xRESTART: BOOL; xFinish: BOOL; xStop: BOOL; pSlave: POINTER TO ETCSlave; TP1 : TP; STS11: WORD; pSlave6: POINTER TO IoDrvEthercatDriverLib.ETCSlave; MP1: INT; TON1 : TON; xSTAT: BOOL; TP_1 :standard.TP; END_VAR TON1(IN:= NOT TON1.Q, PT:= T#300mS ); TP_1(IN:= ton1.Q, PT:= t#2s ); EtherCAT_Master.xRestart := xRESTART; EtherCAT_Master(); EtherCAT_Master(); xFinish := EtherCAT_Master.xConfigFinished; EtherCAT_Master.xStopBus := xSTOP; EtherCAT_Master(); pSlave := EtherCAT_Master.FirstSlave; WHILE pSlave <> 0 DO pSlave^(); IF pSlave^.wState = ETC_SLAVE_STATE.ETC_SLAVE_OPERATIONAL THEN xRESTART := FALSE; ELSE xRESTART := TP_1.Q; END_IF pSlave := pSlave^.NextInstance; END_WHILE
Last updated: 2026-02-14
Post by aapostolidis on _NEW when used with classes and interfaces. Interface shows "Hidden Instance" in watch.
CODESYS Forge
talk
(Post)
Hello, im using dynamic memory allocation with the NEW()-operator. When i instanciate a class with the NEW()-operator and want to debug/watch the interface of the class, the watch is only showing "Hidden Instance" (See attached screenshot). Is there any possibility to debug the interface data ? The interface is working properly but the debugging by the watch is not possible, what is a big disadvantage. Thank you. Best Regards, Alexander
Last updated: 2026-03-24
Post by lofty on CODESYS Download Issue
CODESYS Forge
talk
(Post)
I am attempting to install CODESYS 3.5.22.20 and the installer gets stuck at "Install Package CODESYS Compatibility Package 3.5.17.20" every single time. I've tried reinstalling the software multiple times and the same issue persists. I've tried running the installer as an administrator and even turned off my virus protection and the same issue persists. I've attached a photo for reference. Has anyone run into this issue before or have any idea what I can do to complete the install?
Last updated: 2026-05-26
Post by dmb-fan on Attemp Convert old V2.3 projects : Error HRESULT: 0x80010105 (RPC_E_SERVERFAULT))
CODESYS Forge
talk
(Post)
I had runnig this already. Then I updated to SP22 patch3. After that I got always this error: ===== Project importieren: XXXXnameYYYYYY ===== *[FATALER FEHLER] Fehler beim Import des Projekts: Ausnahmefehler des Servers. * [FATAL ERROR] Error importing the project: Server exception. (Exception to HRESULT: 0x80010105 (RPC_E_SERVERFAULT)) I delete the version and installed again. Same. I uninstalled all CoDeSys on the PC and installed the old SP22 patch2 new. Same error by opening old projects. Immediatly, not by converting. Convert V3.5.17 was always installed. What is happening or what can I do?
Last updated: 2026-08-11
Post by tarek on How to add/Scan devicenet Master/Slave
CODESYS Forge
talk
(Post)
Hello, i have a similar problem with this. Im using an EL6752 from Beckhoff DeviceNet Master and i dont have an EDS for the comms with the slave (EVO GT II Valve). In CODESYS they dont let me put a digital slave. My question, how can i add a slave in the EL6752 the Process data mapping to see values. I cant add a DeviceNet slave in the tree, thanks
Last updated: 2026-09-14
Post by dmb-fan on From target start Win OnScreenKeyboard
CODESYS Forge
talk
(Post)
Hi ! I am get crazy.... I try to start osk.exe from Visu or PLC. From Visu I can't load it, always error (It change from programm execute always to load receipe ..!?!?) From PLC always freeze of PLC, - I allowed the win service of the PLC the data exchange between desktop and service - I allowed in ..user.cfg [SysProcess] Command=AllowAll Shutdown with SysProcessExecuteCommand works, but 'osk.exe' or the complete path always crashed the system. And like always: No documentation. Just guessing. Or know somebody more and have a link for me? THANKS !
Last updated: 2026-10-27
Post by eschwellinger on communication
CODESYS Forge
talk
(Post)
depends on if you use PFC200 SL from CODESYS store or the Wago target for the PFC. If you use the SL product you need to setup the interface by a plcshell command...
Last updated: 2023-08-19
Post by kunz on Profinet Device keeps abort connection with AR alarm.ind(err)
CODESYS Forge
talk
(Post)
Can somebody explain what the error Connection aborted: AR alarm.ind(err) exactly mean? I have the same Problem and dont know how to solve the issue
Last updated: 2023-08-21
Post by reinier-geers on Ping By Name
CODESYS Forge
talk
(Post)
To bad. Controller uses Version 9.2 But i dont see a lower version of net bas Service. Maybe i can try a linux command.
Last updated: 2023-08-29
Post by roundex on CSVReaderInit returns error : INVALID_HANDLE
CODESYS Forge
talk
(Post)
Could you please give me an example where to select new path in plc. Right now my csv files are placed into /home/user/csvfiles
Last updated: 2023-08-30
Post by felipemsgarcia on EtherCAT - Force Control Word
CODESYS Forge
talk
(Post)
What worked for me: Use SMC_SetControllerMode and set the nControllerMode to SMC_nocontrol. With that, you can control the drive via Modes of Operation(16#6060) and Controlword(16#6040) directly. Hope that helps, Cheers!
Last updated: 2023-08-31
Post by tvm on Ranges, Lambdas, on Fixed arrays of structs
CODESYS Forge
talk
(Post)
Have you looked at this? https://forge.codesys.com/prj/codesys-example/element-collect/home/Home/ It's not exactly what you're looking for, but I've been able to make some things work more efficiently using this library.
Last updated: 2023-08-31
Post by automa on Defining local variables that can be independent with several users.
CODESYS Forge
talk
(Post)
Hi, I am looking for a way to define a local variable that will be multi user independent. This is so several user can connect at the same time select frames independent of each other.
Last updated: 2023-09-04
Post by laazik2 on v3.5 SP19 - Modbus TCP Devices - Channel Limit?
CODESYS Forge
talk
(Post)
I am actually wondering as well if there are plans to fix it or not? As adding two modbus devices creates it's own problems with connection limits and other issues, which some slave devices have.
Last updated: 2023-09-05
Post by tvm on Web Client (HMI) Disconnects from Webvisu (Weidmuller u-OS)
CODESYS Forge
talk
(Post)
We have seen this kind of thing before. I have two questions: 1. What kind of HMI are you using? 2. When this happens, are you able to connect using https, on port 8089?
Last updated: 2023-09-06
To search for an exact phrase, put it in quotes. Example: "getting started docs"
To exclude a word or phrase, put a dash in front of it. Example: docs -help
To search on specific fields, use these field names instead of a general text search. You can group with AND or OR.