Post by wollvieh on License Activation Problems ^{CODESYS Forge talk (Post)}
on a raspberry pi delete the folder and its content before licensing. /var/opt/codesys/cmactlicense If you plug this SD card in another raspi ( which has another hw-serial number) you'll get a second empty softcontainer. This could lead to an unlicensed PFC (it could only handle one container) The solution is: To delete the /var/opt/codesys/cmactlicense directory and content of it and then aktivate the lizenz via WibuCmRau file and Lizenzmanager.
Last updated: 2024-06-24

Post by mizi on SM_Drive_Virtual ^{CODESYS Forge talk (Post)}
Hi I recently started learning Codesys SoftMotion. At first, I mainly used YouTube videos. I stopped at two videos where the same problem keeps recurring. fbReadPos( Axis := X_Axis, Enable := TRUE, Position => gAxes.lrActualPos); <- axis cannot move I checked the entire code line by line. Zero errors. GPT spits out nonsense, throwing up increasingly worse errors. And when I copy its code, it says the code is wrong and gets stuck in a loop of its own stupidity. Can anyone explain why it doesn't work? Link to the video below: https://www.youtube.com/watch?v=CYa2HvYZgbM&list=PLsEhEcYjG7na0OveU7cqFXBx7ATyGGn0A&index=3
Last updated: 2025-10-21

Post by eschwellinger on Unrecoverable SoftMotion state after switch to PreOp ^{CODESYS Forge talk (Post)}
i would recommend to check the plc log..
Last updated: 2025-10-23

Post by dinesh-vamtec on SysProcessExecute ^{CODESYS Forge talk (Post)}
I'm trying to open the Help.chm file in CodeSys ST, not working.
Last updated: 2025-10-24

Post by mg0815 on ERROR: Calling the program "AlarmStorage_Prg" is not allowed from multiple tasks ^{CODESYS Forge talk (Post)}
...
Last updated: 2025-11-04

Post by r-c-r on SM3RaspiStepper 0.0.0.6 issue ^{CODESYS Forge talk (Post)}
Version 0.0.0.7 - still the same problem. Any updates?
Last updated: 2025-12-05

Post by lbartik on J1939 TX/RX PDU1 ^{CODESYS Forge talk (Post)}
Is it possible to transmit a PDU1 PGN using the J1939 manager and local device? What if I need to transmit a PGN RQST via 0xEA00 (PGN 59904)? How would I do this P2P (Destination < 0xFF) or broadcast (Destination 0xFF)? I don't think this is possible for any destination type. I don't think it's possible to receive broadcast PDU1 messages either. For example, an address claim PGN 60928 (0x18EEFF80) is addressed to all nodes (0xFF) and not any specific local device so it will be filtered out. These are major oversights in the IoDrvJ1939 library to not support every PDU1 RX/TX scenario. IoDrvJ1939 supported scenario: 1. Receive (RX) PDU1 (P2P) destination-specific (PDU-specific < 255) to local device with matching address IoDrvJ1939 unsupported scenarios: 1. Receive (RX) PDU1 (P2P) global (PDU-specific = 255) 2. Transmit (TX) PDU1 (P2P) global (PDU-specific = 255) 3. Transmit (TX) PDU1 (P2P) destination-specific (PDU-specific < 255)
Last updated: 2024-09-23

Post by rajatdas2005 on Codesys Virtual control SL ^{CODESYS Forge talk (Post)}
Dear All, This is regarding Codesys Virtual control SL demo version. I am facing one issue. First I will describe the steps what I have followed till now. 1. In a PC I have Windows OS. Here Codesys IDE is installed, and also using the installer option of IDE I have also installed Codesys Virtual control SL. 2. A edge-gateway is also running in the same windows PC as local host. 3. Next I have a seperate PC with Ubuntu OS with docker installed. This machine is in the same network. 4. Now I have created a project in Windows machine using device "Codesys Virtual control SL". 5. In the Ubuntu machine I am running the Codesys Virtual control SL as docker and it is using the ubuntu machine network only. 6. Next using the localhost edge-gateway when I am searching the virtual control SL docker it is able to detect it. (screenshot attached) 7. But after creating the creadentials it is telling No Device is responding. 8. I have also checked the wireshark logs and able to see that in destination port 11740 data is coming. 9. From windows PC telnet ip 11740 is also working. 10. Ping is also working ===========================================LOGS ========================= sudo ss -tlnp | grep -E "(443|1217|4840|8080|11740)" LISTEN 0 10 10.135.114.142:4840 0.0.0.0: users:(("codesyscontrol.",pid=41864,fd=21)) LISTEN 0 10 172.18.0.1:4840 0.0.0.0: users:(("codesyscontrol.",pid=41864,fd=24)) LISTEN 0 10 172.17.0.1:4840 0.0.0.0: users:(("codesyscontrol.",pid=41864,fd=23)) LISTEN 0 10 127.0.0.1:4840 0.0.0.0: users:(("codesyscontrol.",pid=41864,fd=26)) LISTEN 0 10 192.168.122.1:4840 0.0.0.0: users:(("codesyscontrol.",pid=41864,fd=22)) LISTEN 0 5 0.0.0.0:11740 0.0.0.0: users:(("codesyscontrol.",pid=41864,fd=20)) LISTEN 0 128 0.0.0.0:8080 0.0.0.0: users:(("python3",pid=1280,fd=4)) LISTEN 0 10 172.19.0.1:4840 0.0.0.0: users:(("codesyscontrol.",pid=41864,fd=25))
Last updated: 2025-08-06

Post by sukrit on What licenses are required for runtime on raspberry pi cm4 ^{CODESYS Forge talk (Post)}
We have developed a project for 2 servo motors using raspberry pi computemodule 4 on ethercat master. we are using web visualization for display different screens. project is running well in demo. we want to implement it in production envoirment. being new still wondering which licences i need. Can We get this information in codesys devlopment software. code size is approx 5 mb, 1 instance of etharcat master and aproox 100 variables in visaualization.
Last updated: 2023-10-17

Post by seler on Custom button with output status ^{CODESYS Forge talk (Post)}
Just to clarify. Output for lamp will have two inputs: from plc IN (wall switch) and from visu button. Until now I had separate object for visu button and separate for visu lamp. Now I want it to be one object, bulb icone which will change color on lamp status and yet by touching it will change visu button state. Tried "Switch Image" object but there is no way to assign switch var.
Last updated: 2025-11-19

Post by ricola on ERROR: CodeMAccess2: Used CmRuntime 2.61.2705.500 is too old ^{CODESYS Forge talk (Post)}
hi there , can someone tell me how to deal with this error , please? I use the Linux ARM64SL (4.11) on a bullseye distro and when I want to update or install some package, I have the following reply : pi@NanoPi-R5C:~$ sudo apt upgrade Reading package lists... Done Building dependency tree... Done Reading state information... Done You might want to run 'apt --fix-broken install' to correct these. The following packages have unmet dependencies: ** codesyscontrol : Depends: codemeter but it is not installable or codemeter-lite but it is not installable** E: Unmet dependencies. Try 'apt --fix-broken install' with no packages (or specify a solution). and if I try apt --fix-broken install as suggested, I have a proposal to uninstall codesyscontrol ... :-D so I tried to search if there is some Codesys repo: nothing, then I tried to see if ther was something inside Codesys dev (V3.5.20) and I only found that by reading/requesting my device, i spoted that codemeter was too old . I don't see how to deal with this issue. is there a codemeter.deb somewhere ? thanks in advance for any help.
Last updated: 2024-09-17

Post by thewizard8 on Raspberry PI4 Serial Port ^{CODESYS Forge talk (Post)}
Hi Dear All, I'm using my raspberry PI4 as a CoDeSyS PLC (Build from scratch with custom electronics). I was able to implement all fieldbuses with the exception of Modbus Serial. I'm using the internal Port (GPIO) and I configured it in /etc/Codesyscontrol_user.cfg the following away: [SysCom] Linux.Devicefile.1=/dev/ttyUSB0 Linux.Devicefile.2=/dev/ttyS0 I'm using COM2 on Master configuration. I'm using a interface board from TTL/RS485 (bidirectional board), and it's works perfectly with other devices but not in CoDeSyS. I'm able to send data with python script and read it on my pc using putty, but when I use a modbus slave simulator to interface with codesys I always get red icons on master and slave. (Please find image attached). I'm pretty shure that this might be a bad parameter on my CoDeSyS runtime configurstion file. Can someone help me? I'm stuck and this is for my master degree certification.
Last updated: 2024-03-18

Post by marekxc on Error C0521 - unknow compiler ^{CODESYS Forge talk (Post)}
Select in tree "DEVICE", right-click and select "Update Device" Select "Library manager" and Change the version of the Library (down manualy). Samoetimes "Try reload Library". If you open a project version 3.5.19 in version 3.5.16, there are difficulties.
Last updated: 2023-09-02

Post by transmin01 on CANbus issue ^{CODESYS Forge talk (Post)}
Hi, I have been trying to get a CANbus device working with Codesys 3.5SP19 patch1 via a Beckhoff EL6751 gateway without success. I have the CANOpen_Manager and CANopen device configured but this will not run. Is there any code required to kickstart the CANbus comms into action? Regards Trevor
Last updated: 2023-09-13

Post by timvh on Troubles with using CAN API ^{CODESYS Forge talk (Post)}
In the example project, you can see that a CAN.CANAreaReceiver is used which has an VAR_IN_OUT reference to a RECEIVER_AREA structure. This structure has a dwIdStart and dwIdEnd to filter a range of ID's and process them through the referenced msgProcessor.
Last updated: 2023-09-19

Post by chris12345 on Calling OPC UA Methods from UaExpert ^{CODESYS Forge talk (Post)}
Hi, Is it possible to generate an .xml file with FBs and methods from Codesys? Or do I need a separate program to generate the .xml file? Or is there a otherway to use methods via opc ua from the own project?
Last updated: 2023-09-20

When using the Element Collections library, is there a proper way to remove a dynamically created collection from memory? ^{CODESYS Forge talk (Thread)}
When using the Element Collections library, is there a proper way to remove a dynamically created collection from memory?
Last updated: 2022-09-08

Post by rschwager on description about the build compiler definition ^{CODESYS Forge talk (Post)}
Hi CODESYS moderators and user! Is there any description about the compiler definition in property of application? e.g.: CANOPEN_NO_HEARTBEATPRODUCING Is there more definition? Best regards Robert
Last updated: 2023-09-26

Post by derpaul on Official MQTT-Client: MAX_RECEIVE_BUFFER_SIZE_EXCEEDED ^{CODESYS Forge talk (Post)}
Thank you very much so far - As I finaly decided to make an update on the PFC200 - as I've to get it up and running again. But something failed there and no I'm having an other Problem :-( I'll come back to this, when the error comes back!
Last updated: 2023-09-28

Post by simond on The required device description is not installed.. ^{CODESYS Forge talk (Post)}
Hi folks, can someone please tell me how to go about fixing this issue? I am getting this error when I implement an instance of the J1939_Manager. Thanks Simon
Last updated: 2023-10-03

Post by timvh on Visualization using methods and cyclic ST-calls ^{CODESYS Forge talk (Post)}
I think you want to implement client side scripting? Maybe creating HTML5 objects is an option, because the JavaScript is executed on the client side. See html5
Last updated: 2023-10-03

Post by davidbo on Is OPC communication possible with server certificate but no client certificate ^{CODESYS Forge talk (Post)}
I was just wondering is the following option possible and what the settings should be. Is OPC communication possible with only and mandatory server certificate but no client certificate?
Last updated: 2023-10-06

Post by damian177 on MQTT_client disconnect when call MQTT_sunscribe ^{CODESYS Forge talk (Post)}
Probably I have the same problem, When I connect to broker and try subscribe to much topics then the client return error, did you solve your problem ?
Last updated: 2023-10-10

Post by sivakov on Change the default ssh port ^{CODESYS Forge talk (Post)}
Of course there is! =) just edit file/etc/ssh/sshd_config and restart ssh service. but you'll lose the possibility of runtime management through "update Linux", so there enother question - how to change default port in codesys it-self?
Last updated: 2023-10-11

When using the Element Collections library, is there a proper way to remove a dynamically created collection from memory? ^{CODESYS Forge talk (Thread)}
When using the Element Collections library, is there a proper way to remove a dynamically created collection from memory?
Last updated: 2023-10-31

Sort by relevance or date