Post by arvind on communication ^{CODESYS Forge talk (Post)}
HI All past two weeks im trying to configure and establish communication between wago rs485 fieldbus coupler(750-315/300-000) with wago pfc 200 plc but not able to communicate can you peoples help me to configure and establish communication using codesys v3.5 and above
Last updated: 2023-08-19

Post by eschwellinger on RPI Zero w - Edge gateway cant install ^{CODESYS Forge talk (Post)}
ok now it is clear - this is a single core Pi Zero W. For this device there is no edge device available. But just for working with CODESYS it is not really needed and yes plc runs only for 2h unlicensed.
Last updated: 2023-09-13

Post by davidredondo on Send file from codesys to...... ftp, cloud, etc ^{CODESYS Forge talk (Post)}
Hi all, I am also looking for a solution to transfer a csv file from ifm HMI-PLC to some cloud and finally to node-red, for example. Do any of you advise me how to do it? Thanks
Last updated: 2023-11-08

Post by ibarragerman on PLCHandler where is it ^{CODESYS Forge talk (Post)}
Hello, someone has some example to use PLC Handler? Without SDK. I would like to make some test before to go forward buying SDKs.
Last updated: 2024-07-26

Post by ibarragerman on PLCHandler where is it ^{CODESYS Forge talk (Post)}
Hello, someone has some example to use PLC Handler? Without SDK. I would like to make some test before to go forward buying SDKs.
Last updated: 2024-07-26

Post by ibarragerman on PLCHandler where is it ^{CODESYS Forge talk (Post)}
Hello, someone has some example to use PLC Handler? Without SDK. I would like to make some test before to go forward buying SDKs.
Last updated: 2024-07-26

Post by elayaraj on Codesys Soft PLC OPC UA server ^{CODESYS Forge talk (Post)}
Hi, You may refer to this below video link to get some idea.. hopefully it works https://www.youtube.com/watch?v=RBMff-IlPA4
Last updated: 2024-08-30

Post by trycyclepower on EtherCAT drive going into fault mode require power cycle everytime ^{CODESYS Forge talk (Post)}
I have EtherCAT servo drive lost communication with PLC everytime it gets faulted, it does not not communicate until I power cycle everything again, how to solve this issue?
Last updated: 2024-09-11

Post by prakashkoladiya on CODESYS Gateway is not running ^{CODESYS Forge talk (Post)}
Suddenly CODESYS gateway has been stopped running as below picture so I’m not able to scan network PLC. I also tried to start CODESYS gateway service manually but its giving error as below. Have you faced this kind of problem before ??
Last updated: 2024-10-08

Post by tmo21 on Automation server - trends stop recording - need to manually reconnect ^{CODESYS Forge talk (Post)}
Hi Edwin, Thanks for your message. Edge controller Version: 4.4.0.0 based on 3.5.17.30 PLC version: Device Identification Name CODESYS Control for Raspberry Pi MC SL Vendor 3S - Smart Software Solutions GmbH Device type Softmotion3S Firmware version 4.4.0.0
Last updated: 2024-10-23

Post by kumareasu on Windows on ARM / Microsoft Surface ^{CODESYS Forge talk (Post)}
I too need this information. Is it possible to install CoDeSys runtime and convert a ARM system installed Windows IoT as OS and convert as PLC?
Last updated: 2024-11-16

Post by jaguerop on j1939 ^{CODESYS Forge talk (Post)}
buenas noches, acudo a sus grandes conocimientos alguien quien mepuede orientar en j1939 y codesys 2.3 deseo controlar un motor deutz a traves de un plc CR0020 la aceleracion del motor diesel
Last updated: 2025-07-13

Post by timvh on Codesys Control for PLCnext (PLC - AXL F 2152) ^{CODESYS Forge talk (Post)}
Do not filter on Phoenix devices. First add an Ethernet device (from CODESYS). Then add a Profinet Controller (from CODESYS). Then add your Phoenix devices to this CODESYS Profinet Controller.
Last updated: 2025-09-09

Post by dkugler on Project loses 'Download time' information ^{CODESYS Forge talk (Post)}
if this happens I go to --> Build --> Generate code then there exists a IDE Code and a PLC/API code and comparison before download is possible. Give it a try?
Last updated: 2025-09-18

Post by jinlee on Multiple WebVisu ^{CODESYS Forge talk (Post)}
Hi there, I am having a similar problem like you. I have 3 screens connected to one PLC. I have set 3 different URLs for them. But 3 of them are still dependent to each other. How can I make them independently ? Kind regards, Jin.
Last updated: 2024-01-25

Post by trycyclepower on Only single ehternet ip drive is communicating ^{CODESYS Forge talk (Post)}
Hi all, I have two ethernet IP drives not communicating together. If I disable one, then other one starts working. ENIPScnannerIOTak cycle is setup as 20ms. Also, PLC updating variables setting is on.
Last updated: 2024-03-08

Post by wiresplus on Remote connection to ifm PLC & HMI ^{CODESYS Forge talk (Post)}
I use these Teltonika routers with ZeroTier rather than OpenVPN - works better for me. I can show you how if you like?
Last updated: 2024-04-13

Post by andreag0 on How to access to variable value through symbolic string name ^{CODESYS Forge talk (Post)}
Good to know. I am looking for some soluction to avoid PLC Handler and OPC-UA. Thank you.
Last updated: 2024-06-14

Post by gilad on CODESYS SoftMotion Generic DSP402 on WAGO PFC200 + Festo CMMT-AS: MC_Power stays Busy, Controlword remains 0 ^{CODESYS Forge talk (Post)}
Thank you very much, What FESTO provides should work even if I use another PLC (WAGO) that is not from FESTO?
Last updated: 2026-06-30

Post by gseidel on CODESYS SoftMotion Generic DSP402 on WAGO PFC200 + Festo CMMT-AS: MC_Power stays Busy, Controlword remains 0 ^{CODESYS Forge talk (Post)}
Hi gilad, I cannot tell for sure. But I think it should work on any PLC that is capable of doing motion control. Best regards, Georg
Last updated: 2026-07-01

Post by osande on V3.5 SP22 Patch1 ^{CODESYS Forge talk (Post)}
... and SP21 P6 also. Kind of bummer, migrating from TIA Portal to Codesys for PLC educational courses. These kind of bugs, and other deficiencies, really makes me regret my choice.
Last updated: 2026-05-06

Post by axberry on CODESYS Control for Raspberry Pi 5 - "Hardware version or firmware version not supported" on Rev 1.1, persists across multiple runtime versions and OS images ^{CODESYS Forge talk (Post)}
Hi, I'm trying to run CODESYS Control for Raspberry Pi SL on a Raspberry Pi 5, and the runtime consistently fails to start with the following error when launched manually: ooops... this runtime was built for RASPBERRYPI. Hardware version or firmware version not supported! (-18, 0x00000BB8, 0xFFFFFFFB) Hardware: Raspberry Pi 5 Model B Rev 1.1 Revision code: d04171 CPU: aarch64, BCM2712 Serial number is correctly exposed via /proc/cpuinfo and /proc/device-tree/serial-number /proc/device-tree/model correctly reports "Raspberry Pi 5 Model B" What I've tried (all resulting in the same error): CODESYS Control for Raspberry Pi SL 4.11.0.0 (SDK 3.5.19.61) — the version that introduced Pi 5 support CODESYS Control for Raspberry Pi SL 4.21.0.0 (SDK 3.5.22.20) — latest available Raspberry Pi OS Bookworm (64-bit) with kernel 6.12.93+rpt-rpi-2712 (June 2026 build) Fresh install on Raspberry Pi OS Bookworm (64-bit) with an older image from November 24, 2025 — same error, ruling out a kernel-version regression Bootloader/EEPROM confirmed up to date (rpi-eeprom-update reports "up to date") Clean purge and reinstall of the codesyscontrol package each time (verified via dpkg -l, no leftover files) Verified /etc/codesyscontrol/3S.dat correctly symlinks to /etc/codesyscontrol/3S_aarch64.dat The service starts (systemctl status briefly shows active (running) with a real PID under /opt/codesys/bin/codesyscontrol.bin), but crashes shortly after and the process disappears — port 11740 never opens. Since this happens identically across two different runtime versions and two different OS images (5+ months apart), it doesn't seem to be a kernel/firmware timing issue. Could this be specific to the Rev 1.1 board revision, or is there a known issue with the hardware detection logic in the SL runtime that I should be aware of? Happy to provide full debug logs (-d flag output) or journalctl output if useful. Thanks in advance!
Last updated: 2026-08-10

Post by oi18ct on ARM SL Development Board Recommendation ^{CODESYS Forge talk (Post)}
Hello codesys forum, My company is looking at developing a solution with Codesys ARM SL. The requirements will not tax the capabilities of Codesys. I would like to buy an AMR 7 or 8 Dev Board for experimenting. I am looking for a recommendation as I have minimal experience with Linux. Any input from the forum would be most appreciated as the hardware requirements as provided by Codesys for ARM SL seem pretty minimal (basically a arm7 or 8 with Debian is all). Our needs are small in scale- something like 8 digital inputs, 6 digital outputs, 2 analog inputs and 1 analog output. A small gui will be published via web visualization for external display (no local display). Communications with ModbusTCP and uart/RS485. It may be necessary to access i2c and make c or python calls to some existing code that is pretty small. Something like the EMCraft STM32MP1 SOM Starter Kit or Octavo Systems OSD32MP1-RED development board? Ideally something that has a path to a SoM for production. Kontron appears to have some interesting options too. Just having a hard time deciding where to start. Thanks in advance... LC
Last updated: 2023-11-11

Post by jeroenaero on Problem with CodeSys Control SL Deploy Tool 4.15.0.0 ^{CODESYS Forge talk (Post)}
Hello, We just installed the new version of CodeSys Control SL Deploy Tool 4.15.0.0 but we get the following error when we try to add a VPLC. Can someone of the CodeSys team fix this issue? the object reference is not set to an instance of the object Zie het einde van dit bericht voor meer informatie over het aanroepen van JIT-foutopsporing (Just In Time) in plaats van dit dialoogvenster. ** Tekst van uitzondering ** System.NullReferenceException: De objectverwijzing is niet op een exemplaar van een object ingesteld. bij _3S.CoDeSys.RuntimeDeployTool.Views.AddNewInstanceForm.ShowAllImages() bij _3S.CoDeSys.RuntimeDeployTool.Views.AddNewInstanceForm..ctor(List1 virtualControls, List1 existingNames) bij _3S.CoDeSys.RuntimeDeployTool.Views.MainEditorTab_Operation.OnAddInstanceClick() bij _3S.CoDeSys.RuntimeDeployTool.Views.MainEditorTab_Operation.bt_add_Click(Object sender, EventArgs e) bij System.Windows.Forms.ToolStripItem.RaiseEvent(Object key, EventArgs e) bij System.Windows.Forms.ToolStripButton.OnClick(EventArgs e) bij System.Windows.Forms.ToolStripItem.HandleClick(EventArgs e) bij System.Windows.Forms.ToolStripItem.HandleMouseUp(MouseEventArgs e) bij System.Windows.Forms.ToolStripItem.FireEventInteractive(EventArgs e, ToolStripItemEventType met) bij System.Windows.Forms.ToolStripItem.FireEvent(EventArgs e, ToolStripItemEventType met) bij System.Windows.Forms.ToolStrip.OnMouseUp(MouseEventArgs mea) bij System.Windows.Forms.Control.WmMouseUp(Message& m, MouseButtons button, Int32 clicks) bij System.Windows.Forms.Control.WndProc(Message& m) bij System.Windows.Forms.ScrollableControl.WndProc(Message& m) bij System.Windows.Forms.ToolStrip.WndProc(Message& m) bij System.Windows.Forms.Control.ControlNativeWindow.OnMessage(Message& m) bij System.Windows.Forms.Control.ControlNativeWindow.WndProc(Message& m) bij System.Windows.Forms.NativeWindow.Callback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam) ** Geladen assembly's ** mscorlib Assembly-versie: 4.0.0.0 Win32-versie: 4.8.9300.0 built by: NET481REL1LAST_C
Last updated: 2025-04-24

Post by antonz on CoDeSys v3.5: creating libraries for both 32-bit and 64-bit controllers ^{CODESYS Forge talk (Post)}
Looking for thoughts on creating libraries that can be used on both 32-bit and 64-bit controllers. We are currently writing software in CoDeSys for both target types and will continu to do so for the near future. Projects are always unique, no straight forward copy/paste, yet there is enough similarity between them to use libraries for recurring logic. I do not want to create and maintain twice for both platforms if this is not absolutely necessary. I am aware of useful datatypes like __XWORD, __XINT, __UXINT. Still looking for more information and/or sample code for portable pointer arithmetic. In addition to that: how should one go about when creating and working with compiled libraries? Would I need to compile the same lib twice, once for 32-bit targets once for 64-bit targets? I would end up with two different libs with the same namespace, which does not sound elegant to me. Note: I did not intentionally make the previous paragraph bold. The forge forum software seems to do this automatically upon insertion of a word which starts with two underscores, e.g. __XWORD (yeah, here we go again :) )
Last updated: 2025-08-25

Sort by relevance or date