Post by rossanoparis on CAN TX regression in Control for Raspberry Pi 4.21.0.0 with CAN API library (RX works, TX silently fails)
CODESYS Forge
talk
(Post)
Environment: Target: Revolution Pi (Kunbus RevPi), armv7l 32-bit OS: Raspbian GNU/Linux 9 (Stretch), kernel 4.19.95-rt38-v7 (SMP PREEMPT RT, built 2022-03-22) CAN: via SocketCAN (can0) Runtime: CODESYS Control for Raspberry Pi SL IDE: CODESYS V3.5 SP22 + patch 3 (previously V3.5 SP22 + patch 2, where everything worked with runtime 4.18.0.0) Library: CANBusAPI from the "CAN API" package, version 1.0.0.3 Summary: The setup worked correctly with V3.5 SP22 + patch 2 and runtime 4.18.0.0. After updating the IDE to SP22 + patch 3 and the runtime to 4.21.0.0, CAN transmission via the CANBusAPI library stopped working. Reception is unaffected. There are no error indications anywhere: the application runs normally and the CAN diagnosis reports a healthy bus. Systematic testing (below) shows the problem follows the runtime version, not the IDE update. Regression isolation: The same application (compiled under SP22 + patch 3, unchanged between tests) was downloaded to the same target with different runtime versions, changing only the runtime each time: 4.18.0.0: TX and RX both work 4.19.0.0: TX and RX both work 4.20.0.0: TX and RX both work 4.21.0.0: RX works, TX does not The behavior is fully reproducible in both directions (downgrading to 4.20 restores TX, upgrading to 4.21 breaks it again). Hardware, wiring, OS, project, and application code are identical across all tests. Diagnostic data (CANBusDiagnosis FB, while the application is transmitting on 4.21): ctSendCounter: incrementing normally ctTxErrorCounter: 0 ctRxErrorCounter: 0 eState: ERROR_FREE xBusAlarm: FALSE So the library accepts and counts the outgoing messages, no TX errors are reported, and the CAN controller state stays error-free, but the messages never reach the other nodes on the bus. Expected behavior: Messages sent via CANBusAPI (CANDriver / SendMessage) are transmitted on the bus, as with runtime versions up to and including 4.20.0.0. Notes: I am aware that the CAN API package (1.0.0.3, from 2016) is old; however, the regression is tied to the runtime version, since the identical binary works on 4.18-4.20. Questions: Is there a known change in CmpSocketCanDrv / CmpCAACanL2 between 4.20.0.0 and 4.21.0.0 that could affect TX via the CAN API library? Is runtime 4.21.0.0 still supported on Debian 9 Stretch (kernel 4.19, RT-patched), or is a newer OS required? If a minimum OS/kernel requirement was introduced with 4.21, is it documented?
Last updated: 2026-08-17
Post by s1ack on Wago PFC200 Ethernet / IoDrvEthernet Issue?
CODESYS Forge
talk
(Post)
CODESYS Control for PFC200 4.13.00 CODESYS IIoT Libraries SL 1.11.0.0 Application Based License: CODESYS Control Standard M I have (2) projects with similar code base and both using Wago PFC200. On the second project I am seeing 2 things that I have not been able to resolve: 1) Errors in the log under the Ethernet Item: IoDrvEthernet: [PCI\E1Q51CE62] Could not be found on target! Please check the Ethernet settings. 2) Exception for CPU Load. "Processorload watchdog: plcload=100, maxplcload=95" I have slowed down cyclic tasks on this project, even though on the first project there is actually more code - and it does not exhibit this behavior. In looking at the CPU loading via Linux 'TOP' command there appears to be 20% idle. So plenty of headroom (my opinion). In an effort to troubleshoot I have duplicated the target hardware on my bench. It ran overnight without a CPU load exception. On the test system, I have tried (3) version of the ethernet device. 3.5.16.0 3.5.17.0 and 4.2.0.0 Presently the log does not show the error, but status says the module reports an error. I really do not know if this issue is related to the CPU load exception. The issue does not appear to effect ethernet communications (ModbusTCP or SNMP or Webvisu or PuTTy into Linux Shell). On my test bench I have ModbusTCP slave simulators for all ModbusTCP slaves, but only (1) of the (5) SNMP devices present.
Last updated: 2025-01-21
Post by tk096 on High Cycle Times for SoftMotion_PlanningTask when using AxisGroup
CODESYS Forge
talk
(Post)
Hi, under this circumstances the performance of a Raspberry Pi 4 should be sufficient to run a Softmotion robotics application. A closer look at the project would be required. Maybe you could contact the codesys support? Usually it is recommended to run the planning task cyclically every 2ms with task priority of 0 on a dedicated core. In the task configuration you can have a look at the average and maximum execution time of the planning task. You could use the function block SMC_TuneCPKernel (https://content.helpme-codesys.com/en/libs/SM3_Robotics/Current/SM3_Robotics/POUs/AdministrativeConfiguration/Computation/SMC_TuneCPKernel.html) to define suitable values for the parameters 'fSyncBufferDuration' and 'fPlanningInterval'. However, as previously mentioned, the performance of a Raspberry Pi 4 with realtime patch should be sufficient. The 'fPlanningInterval' parameter specifies the maximum planning step width in seconds. The cycle time of the planning task should not permanently exceed this value. A higher value reduces the computational effort, but can lead to a violation or no full utilization of the set limit values for velocity, acceleration and jerk. From a starting value of 0.016 seconds, the value should be increased gradually until the performance is acceptable. The parameter 'fSyncBufferDuration' specifies the size (in seconds) of the buffer between the planning and fieldbus task. The cycle time of the planning task must not exceed this value at peak times (this will lead to the error SMC_CP_QUEUE_UNDERRUN). A higher value can compensate for peaks in the cycle time of the planning task. At the same time, however, this also increases the latency for executing interrupts and aborting movements.
Last updated: 2024-03-22
Post by manuknecht on Maximum dynamic limits of MC_MoveLinearAbsolute and MC_MoveLinearRelative
CODESYS Forge
talk
(Post)
Hello all I use an axis group with two linear axes in a kinematic system. Using MC_MoveLinearAbsolute and MC_MoveLinearRelative, I am trying to realise dynamic movements (set velocity: 1 m/s, set acceleration: 30 m/s^2) with the highest possible jerk, as I want to compare this with a movement with a trapezoidal velocity profile. However, my measurements show that the axes accelerate with a maximum jerk of approx. 800 m/s^3, even if the value in the function block was set to 10,000 m/s^3. I have already increased the dynamic limits of the two axes accordingly (Velocity: 5000 u/s, Acc-/Deceleration: 250'000 u/s^2, Jerk: 100'000'000 u/s^3, where 1 u = 1 mm), but this had no effect. I have checked the input parameters of the function blocks and the VelFactor, AccFactor and JerkFactor factors are all set to the maximum (value 1). Reducing the cycle time has resulted in a higher jerk, but as we are already working with a cycle time of 1 ms, there is nothing more that can be done here. The axes themselves are still a long way from drawing the maximum current, which is why I assume that this should not be a problem either. Are there other factors or parameters that influence the dynamic limits and therefore allow faster movements? The PLC I am using is a Raspberry Pi 4 and Codesys V3.5 SP20 with all libraries up to date. Thanks in advance Manuel
Last updated: 2024-05-08
Post by imdatatas on MC_CamIn did not work properly with SMC_FreeEncoder on SoftMotion 4.17.0.0
CODESYS Forge
talk
(Post)
Hello, I am facing a problem with the new Softmotion 4.17.0.0 version. Has anyone encountered a similar problem, what is the solution? I would be happy if you could share it. Problem description: -- "SMC_FreeEncoder" encoder axis is the master, -- The motor of the servo driver on the EtherCAT bus is the slave axis. -- When the MC_CamIn block executed, the InSync output is activated. However, although the master encoder axis position value changes, there is no movement in the slave servo axis! Test steps: 1-) EtherCAT servo axis installed, configured and motion test was performed with MC_Jog. No problem. 2-) Softmotion general axis pool > SMC_FreeEncoder was added and pulse amount configuration was performed. No problem. 3-) Incremental encoder actual count value was transferred to the "SMC_FreeEncoder.diEncoderPosition" variable as DINT under the ethercat task in every cycle and the encoder axis position value was observed. No problem. 4-) A simple CAM table with a 1:1 ratio was created under the project tree. (For example: Simply, when the encoder rotates 1 turn, the motor will rotate 1 turn.) 5-) The SMC_FreeEncoder axis enabled with MC_Power and brought to the StandStill state. 6-) The MC_CamTableSelect block was run with default input values ​​(all absolute) and only the Cam table name was specified. The Done output was seen successfully. No problem. 7-) The MC_CamIn block was activated with default input values ​​(absolute) and only the master encoder axis name, slave servo axis name, CamTableID input pins was specified and then "Execute" input set to TRUE. 8-) The InSync output information of the MC_CamIn block observed as TRUE. However, although the encoder axis value changed, the position value of the slave axis did not change at all, it did not move. It always remained at 0.0mm. 9-) When I repeated the same steps above, only changing the master axis to SM_Drive_Virtual instead of FreeEncoder and gave movement to the virtual axis, this time the slave axis moved successfully. However, when the same steps and operations are performed with the same IDE just downgrade SoftMotion version from 4.17.0.0 to 4.10.0.0, everything works normally and without problems as expected in MC_CamIn block with FreeEncoder master. (By the way, The used IDE version is Codesys V3.5 SP20patch3.) Best Regards Imdat
Last updated: 2024-11-11
Post by brandonje on [Error] IoDrvEtherNetIP Library with Weintek
CODESYS Forge
talk
(Post)
I'm using weintek and Codesys V3.5 SP22 when I try to charge an ethernetIP device show me this error: ------ Build started: Application: Device.Application ------- Typify code... [ERROR] cip object, 4.9.0.0 (codesys): TCPIP_Interface: C0231: Expression of type 'BOOL' expected in this place [ERROR] cip object, 4.9.0.0 (codesys): TCPIP_Interface: C0077: Unknown type: '(_pPhysicalLink^._xLinkState <> CmpSysEthernet.OperStatus.SYSETH_OPERSTAT_Up)' [ERROR] cip object, 4.9.0.0 (codesys): TCPIP_Interface: C0077: Unknown type: 'CmpSysEthernet.OperStatus.SYSETH_OPERSTAT_Up' [ERROR] cip object, 4.9.0.0 (codesys): TCPIP_Interface: C0062: 'CmpSysEthernet.OperStatus' is no structured variable [ERROR] cip object, 4.9.0.0 (codesys): TCPIP_Interface: C0063: 'CMPSYSETHERNET, 3.4.3.0 (3S - SMART SOFTWARE SOLUTIONS GMBH)' contains no definition for 'OperStatus' [ERROR] cip object, 4.9.0.0 (codesys): SendEthFrame [TCPIP_Interface]: C0077: Unknown type: 'SysEthernetFrame' [ERROR] cip object, 4.9.0.0 (codesys): SendEthFrame [TCPIP_Interface]: C0046: Identifier '_diAdapterNumber' not defined [ERROR] cip object, 4.9.0.0 (codesys): SendEthFrame [TCPIP_Interface]: C0032: Cannot convert type 'Unknown type: '_diAdapterNumber'' to type 'DINT' [ERROR] cip object, 4.9.0.0 (codesys): SendEthFrame [TCPIP_Interface]: C0032: Cannot convert type 'Unknown type: 'ADR(ethFrame.ethData)'' to type 'POINTER TO StructEthernetframe' [ERROR] cip object, 4.9.0.0 (codesys): SendEthFrame [TCPIP_Interface]: C0077: Unknown type: 'ethFrame.ethData' [ERROR] cip object, 4.9.0.0 (codesys): SendEthFrame [TCPIP_Interface]: C0077: Unknown type: 'SysEthernetFrame' [ERROR] cip object, 4.9.0.0 (codesys): SendEthFrame [TCPIP_Interface]: C0032: Cannot convert type 'Unknown type: 'ethFrame.udFrameLen'' to type 'ANY' [ERROR] cip object, 4.9.0.0 (codesys): SendEthFrame [TCPIP_Interface]: C0077: Unknown type: 'SysEthernetFrame' [ERROR] cip object, 4.9.0.0 (codesys): _OpenEthAdapter [TCPIP_Interface]: C0032: Cannot convert type 'Unknown type: '((driverInstance * 2) + 1)'' to type 'ANY' [ERROR] cip object, 4.9.0.0 (codesys): _OpenEthAdapter [TCPIP_Interface]: C0077: Unknown type: '(driverInstance * 2)' [ERROR] cip object, 4.9.0.0 (codesys): _OpenEthAdapter [TCPIP_Interface]: C0077: Unknown type: 'driverInstance' [ERROR] cip object, 4.9.0.0 (codesys): _OpenEthAdapter [TCPIP_Interface]: C0046: Identifier 'driverInstance' not defined [ERROR] cip object, 4.9.0.0 (codesys): SendFrame [TCPIP_Interface]: C0077: Unknown type: 'SysEthernetFrame' [ERROR] cip object, 4.9.0.0 (codesys): SendFrame [TCPIP_Interface]: C0231: Expression of type 'BOOL' expected in this place [ERROR] cip object, 4.9.0.0 (codesys): SendFrame [TCPIP_Interface]: C0077: Unknown type: 'SIZEOF(ethFrame.ethData)' [ERROR] cip object, 4.9.0.0 (codesys): SendFrame [TCPIP_Interface]: C0077: Unknown type: 'ethFrame.ethData' [ERROR] cip object, 4.9.0.0 (codesys): SendFrame [TCPIP_Interface]: C0077: Unknown type: 'SysEthernetFrame' [ERROR] cip object, 4.9.0.0 (codesys): SendFrame [TCPIP_Interface]: C0018: 'ethFrame.udFrameLen' is no valid assignment target [ERROR] cip object, 4.9.0.0 (codesys): SendFrame [TCPIP_Interface]: C0077: Unknown type: 'SysEthernetFrame' [ERROR] cip object, 4.9.0.0 (codesys): SendFrame [TCPIP_Interface]: C0032: Cannot convert type 'Unknown type: 'ADR(ethFrame.ethData)'' to type 'POINTER TO BYTE' [ERROR] cip object, 4.9.0.0 (codesys): SendFrame [TCPIP_Interface]: C0077: Unknown type: 'ethFrame.ethData' [ERROR] cip object, 4.9.0.0 (codesys): SendFrame [TCPIP_Interface]: C0077: Unknown type: 'SysEthernetFrame' [ERROR] cip object, 4.9.0.0 (codesys): SendFrame [TCPIP_Interface]: C0201: Type 'SysEthernetFrame' is not equal to type 'SysEthernetFrame' of VAR_IN_OUT respectively REFERENCE 'ethFrame' [ERROR] cip object, 4.9.0.0 (codesys): _CloseEthAdapter [TCPIP_Interface]: C0046: Identifier 'ethClose' not defined [ERROR] cip object, 4.9.0.0 (codesys): _CloseEthAdapter [TCPIP_Interface]: C0018: 'ethClose' is no valid assignment target [ERROR] cip object, 4.9.0.0 (codesys): _CloseEthAdapter [TCPIP_Interface]: C0046: Identifier '_diAdapterNumber' not defined [ERROR] cip object, 4.9.0.0 (codesys): _CloseEthAdapter [TCPIP_Interface]: C0032: Cannot convert type 'Unknown type: '_diAdapterNumber'' to type 'DINT' [ERROR] cip object, 4.9.0.0 (codesys): _CloseEthAdapter [TCPIP_Interface]: C0046: Identifier '_diAdapterNumber' not defined [ERROR] cip object, 4.9.0.0 (codesys): _CloseEthAdapter [TCPIP_Interface]: C0018: '_diAdapterNumber' is no valid assignment target [ERROR] cip object, 4.9.0.0 (codesys): _CloseEthAdapter [TCPIP_Interface]: C0046: Identifier '_stName' not defined [ERROR] cip object, 4.9.0.0 (codesys): _CloseEthAdapter [TCPIP_Interface]: C0018: '_stName' is no valid assignment target [ERROR] cip object, 4.9.0.0 (codesys): _CloseEthAdapter [TCPIP_Interface]: C0046: Identifier '_stDescription' not defined [ERROR] cip object, 4.9.0.0 (codesys): _CloseEthAdapter [TCPIP_Interface]: C0018: '_stDescription' is no valid assignment target [ERROR] cip object, 4.9.0.0 (codesys): AddressConflictDetection [TCPIP_Interface]: C0231: Expression of type 'BOOL' expected in this place [ERROR] cip object, 4.9.0.0 (codesys): AddressConflictDetection [TCPIP_Interface]: C0077: Unknown type: '(_pPhysicalLink^._xLinkState = CmpSysEthernet.OperStatus.SYSETH_OPERSTAT_Up)' [ERROR] cip object, 4.9.0.0 (codesys): AddressConflictDetection [TCPIP_Interface]: C0077: Unknown type: 'CmpSysEthernet.OperStatus.SYSETH_OPERSTAT_Up' [ERROR] cip object, 4.9.0.0 (codesys): AddressConflictDetection [TCPIP_Interface]: C0062: 'CmpSysEthernet.OperStatus' is no structured variable [ERROR] cip object, 4.9.0.0 (codesys): AddressConflictDetection [TCPIP_Interface]: C0063: 'CMPSYSETHERNET, 3.4.3.0 (3S - SMART SOFTWARE SOLUTIONS GMBH)' contains no definition for 'OperStatus' [ERROR] cip object, 4.9.0.0 (codesys): Recv [TCPIP_Interface]: C0077: Unknown type: 'SysEthernetFrame' [ERROR] cip object, 4.9.0.0 (codesys): Recv [TCPIP_Interface]: C0046: Identifier '_diAdapterNumber' not defined [ERROR] cip object, 4.9.0.0 (codesys): Recv [TCPIP_Interface]: C0032: Cannot convert type 'Unknown type: '_diAdapterNumber'' to type 'DINT' [ERROR] cip object, 4.9.0.0 (codesys): Recv [TCPIP_Interface]: C0046: Identifier '_diAdapterNumber' not defined [ERROR] cip object, 4.9.0.0 (codesys): Recv [TCPIP_Interface]: C0032: Cannot convert type 'Unknown type: '_diAdapterNumber'' to type 'DINT' [ERROR] memory block manager, 3.5.21.30 (codesys): ObjectRetain [Disposable]: C0448: Operator '__XADD' is not supported by your current target. At least runtime system version 3.5.14.0 is required. [ERROR] memory block manager, 3.5.21.30 (codesys): ObjectRelease [Disposable]: C0448: Operator '__XADD' is not supported by your current target. At least runtime system version 3.5.14.0 is required. [ERROR] cip object, 4.9.0.0 (codesys): SendFrame [LLDP_Management]: C0077: Unknown type: 'SysEthernetFrame' [ERROR] cip object, 4.9.0.0 (codesys): SendFrame [LLDP_Management]: C0201: Type 'SysEthernetFrame' is not equal to type 'SysEthernetFrame' of VAR_IN_OUT respectively REFERENCE 'frame' [ERROR] cip object, 4.9.0.0 (codesys): SendFrame [LLDP_Management]: C0201: Type 'SysEthernetFrame' is not equal to type 'SysEthernetFrame' of VAR_IN_OUT respectively REFERENCE 'ethFrame' [ERROR] cip object, 4.9.0.0 (codesys): CreateFrame [LLDP_Management]: C0077: Unknown type: 'SysEthernetFrame' [ERROR] cip object, 4.9.0.0 (codesys): CreateFrame [LLDP_Management]: C0032: Cannot convert type 'Unknown type: 'ADR(frame.ethData[0])'' to type 'POINTER TO BYTE' [ERROR] cip object, 4.9.0.0 (codesys): CreateFrame [LLDP_Management]: C0077: Unknown type: 'frame.ethData[0]' [ERROR] cip object, 4.9.0.0 (codesys): CreateFrame [LLDP_Management]: C0077: Unknown type: 'SysEthernetFrame' [ERROR] cip object, 4.9.0.0 (codesys): CreateFrame [LLDP_Management]: C0032: Cannot convert type 'Unknown type: 'SIZEOF(frame.ethData)'' to type 'UDINT' [ERROR] cip object, 4.9.0.0 (codesys): CreateFrame [LLDP_Management]: C0077: Unknown type: 'frame.ethData' [ERROR] cip object, 4.9.0.0 (codesys): CreateFrame [LLDP_Management]: C0077: Unknown type: 'SysEthernetFrame' [ERROR] cip object, 4.9.0.0 (codesys): CreateFrame [LLDP_Management]: C0018: 'frame.udFrameLen' is no valid assignment target [ERROR] cip object, 4.9.0.0 (codesys): CreateFrame [LLDP_Management]: C0077: Unknown type: 'SysEthernetFrame' [ERROR] iodrvethernetip, 4.9.0.0 (codesys): Receive [UcmmReceiver]: C0448: Operator '__COMPARE_AND_SWAP' is not supported by your current target. At least runtime system version 3.5.14.0 is required. [ERROR] iodrvethernetip, 4.9.0.0 (codesys): Send [UcmmReceiver]: C0448: Operator '__COMPARE_AND_SWAP' is not supported by your current target. At least runtime system version 3.5.14.0 is required. [ERROR] iodrvethernetip, 4.9.0.0 (codesys): Enqueue [UcmmQueue]: C0448: Operator '__COMPARE_AND_SWAP' is not supported by your current target. At least runtime system version 3.5.14.0 is required. [ERROR] iodrvethernetip, 4.9.0.0 (codesys): Enqueue [UcmmQueue]: C0448: Operator '__XADD' is not supported by your current target. At least runtime system version 3.5.14.0 is required. [ERROR] iodrvethernetip, 4.9.0.0 (codesys): Enqueue [UcmmQueue]: C0448: Operator '__XADD' is not supported by your current target. At least runtime system version 3.5.14.0 is required. [ERROR] iodrvethernetip, 4.9.0.0 (codesys): Dequeue [UcmmQueue]: C0448: Operator '__XADD' is not supported by your current target. At least runtime system version 3.5.14.0 is required. [ERROR] iodrvethernetip, 4.9.0.0 (codesys): Dequeue [UcmmQueue]: C0448: Operator '__COMPARE_AND_SWAP' is not supported by your current target. At least runtime system version 3.5.14.0 is required. [ERROR] iodrvethernetip, 4.9.0.0 (codesys): Dequeue [UcmmQueue]: C0448: Operator '__XADD' is not supported by your current target. At least runtime system version 3.5.14.0 is required. [ERROR] asynchronous job manager, 5.0.0.0 (codesys): ExtendAsync [FactoryBase]: C0448: Operator '__COMPARE_AND_SWAP' is not supported by your current target. At least runtime system version 3.5.14.0 is required. Compile complete -- 71 errors, 0 warnings Build complete -- 71 errors, 0 warnings : No download possible
Last updated: 2026-08-20
Post by fefefede on Error C0521 - unknow compiler
CODESYS Forge
talk
(Post)
Hello and thanks for reply. I not have "Libray Manager" on "Update Device". I not try to open project but i open Codesys and then create a new project and when try to generate code i have the error :/ I notiche a strnge situation. I have two different software on my pc: CODESYS V3.5 SP15 Patch 4 (with this my new program not work but can open and work with some course example); CODESYS V3.5 SP19 Patch 2 (with this my custom program work) Wich version i must be choose? Why i have two different version? Thanks
Last updated: 2023-09-02
Post by bernd on Version 3.5.19.40 probleme bei FUN mit _to_ im Name
CODESYS Forge
talk
(Post)
Hallo, ich habe von Version 3.5.19.0 auf 3.5.19.40 hochgerüstet, jetzt bekomme ich bei allen FUNs die "to" im Namen haben einen Fehlermeldung. Oft in der OSCAT.LIB verwendet. Gleiche Meldung wenn ich einen FUN neu anlege. Sobald ich das to weglasse z.b. nur "t" ist der Fehler weg. Programm ist unverändert. Fehlermeldung: Typ.... wird nicht unterstützt. Hat jemand das gleiche Problem? Bzw. wo liegt das Problem? Bzw. nutzt jemand das SP4 und bei ihm kommt der Fehler nicht? Läuft bei mir auf Rasperry. Beispiel: DT_TO_SDT -> Fehlermeldung Typ DT_TO_SDT wird nicht unterstützt. DT_T_SDT -> Übersetzung Fehlerfrei
Last updated: 2023-11-09
Post by ewi04 on Recipe Manager - RecipeManCommands, load & write wrong values, Bug?
CODESYS Forge
talk
(Post)
Hallo, I have a strange problem with the recipe manager. ISSUE: When using RecipeManCommands not all values are loaded correctly. Saving a recipe with CreateRecipe(), ReadAndSaveRecipe() or ReadAndSaveRecipeAs() works without any problems. BUT: LoadRecipe(), WriteRecipe() or LoadFromAndWriteRecipe() do not load the data correctly. It is Interesting that we have a different error pattern with LoadRecipe() than with WriteRecipe() or LoadFromAndWriteRecipe(). LoadRecipe() does not load all data and WriteRecipe() or LoadFromAndWriteRecipe() overwrites some data or assigns it incorrectly. And it is also strange that LoadRecipe() writes the values to the PLC. Normally it doesn’t do it. It makes no difference whether the memory type is textual or binary. I have an object consisting of STRUCTs which is inserted in the recipe definition. Environment: Codesys V3.5 SP19 Patch 4 (64Bit), Recipe Management 4.2.0.0 *Add a project (reduced to the problem)
Last updated: 2023-11-15
Post by riccardo on Codesys SP19 patch 4
CODESYS Forge
talk
(Post)
Hallo everyone, I am working on new PLC of Weidmueller that uses Codesys SP19. I made the upgrade at the Patch 4 coming from patch 0. Unce made the upgrade everything is working well in the progect except the web visu user menagent. In the new version, when I perfom the login, I cannot use the keyboard of the device; the window where to digit the user name and password opens, the buttons "OK" and "Cancel" work but the system doesn't allow to put input from the device keybord, the mouse behaves as it is an image. If I active the virtual keypad or numpad it works otherwise nothing. I am wondering if it is a bug of the new package or if I must set something else. Thanks in advance, Riccardo.
Last updated: 2023-11-27
Post by mahmutbeyaz on Create a Motion Profile
CODESYS Forge
talk
(Post)
Dear All, I hope first to get notice and somebody answer my question. How can I create a motion profile with the axis following it (once or periodically)? As my research shows, Schineder has a UI-based (Motion Sizer) program that helps create a motion with different configurations, which is Codesys-based. I need to create a motion profile based on position, changing the speed. (i.e., 0-300mm moves with 300 mm/s, 300-400mm moves with 500 mm/s, 500-800mm moves with 1000 mm/s, and 800-0mm moves with 2000 mm/s). MC_PositionProfile does it time-based, which is not working for me as the axis may not stabilize the position in time, which may cause a big failure in the system.
Last updated: 2023-11-30
To search for an exact phrase, put it in quotes. Example: "getting started docs"
To exclude a word or phrase, put a dash in front of it. Example: docs -help
To search on specific fields, use these field names instead of a general text search. You can group with AND or OR.