Post by svn123 on In Simulation Mode, logic is not executing ^{CODESYS Forge talk (Post)}
Please check the attached snapshot. I am converting an int to real and storing in rVlv01_SV and then scaling the value using LIN_TRAFO. In the bottom Status Bar of Codesys, both RUN and SIMULATION are visible. When I enter value 100 as input to INT_TO_REAL instruction and press Ctrl-F7, the value can be seen at the input but the logic seems not to work. I searched for help but could not find anything relevant. What could be the reason. Codesys ver3.5.11 svn
Last updated: 2023-12-25

Post by andrax on Mux I2C ^{CODESYS Forge talk (Post)}
the TCA9548a does not work in Codesys. In Pyton this is only queried once and in Codesys cyclically. Of course you can also insert a terminating resistor in each port, then you should have no problems. I use this one: https://botland.de/8-bit-multiplexer/12723-qwiic-mux-breakout-8-kanal-modul-mit-i2c-multiplexer-tca9548a-sparkfun-bob-16784-5904422341428.html You can simply set the library to the latest version. You do not need Oscat. Do you need an example project for the BMP280?
Last updated: 2024-01-02

Post by andrax on Mux I2C ^{CODESYS Forge talk (Post)}
the TCA9548a does not work in Codesys. In Pyton this is only queried once and in Codesys cyclically. Of course you can also insert a terminating resistor in each port, then you should have no problems. I use this one: https://botland.de/8-bit-multiplexer/12723-qwiic-mux-breakout-8-kanal-modul-mit-i2c-multiplexer-tca9548a-sparkfun-bob-16784-5904422341428.html You can simply set the library to the latest version. You do not need Oscat. Do you need an example project for the BMP280?
Last updated: 2024-01-02

Post by toby on Codesys Control Raspberry PI 4.10.0 - missing 'Update Raspberry PI' option ^{CODESYS Forge talk (Post)}
Hi Edwin, Thanks for the message. My apologies I should have researched this more thoroughly before posting on here. I found a solution to my issue on this post: https://forge.codesys.com/forge/talk/Runtime/thread/6455efaa17/ I needed to run the 'CODESYS Installer' as an Admin, then install the RPi package v4.10.0 in to my package (v3.5 SP19 Patch 5). Thanks, hope you have a good day. Toby
Last updated: 2024-01-09

Post by durstloescher on Codesys Input Detector ^{CODESYS Forge talk (Post)}
Good morning, I am currently working on implementing a display dimmer. I want the display to dim after X minutes. This works so far. The implementation is done via the Linux subsystem, to which a command is sent to dim the display. However, my problem is resetting the timer when input is received. I want the dimming timer to be reset with each click/touch. Unfortunately, I can't find a suitable solution for this. Are there any ways to do this? Codesys v3.5 SP19 Patch 2
Last updated: 2024-02-15

Post by nano on Is there any support for I2C on Raspberry Pi? ^{CODESYS Forge talk (Post)}
hello jdj this question can be answered well with a pretty good forge documentation: https://forge.codesys.com/drv/io-drivers/doc/Generic/ u r also able to create in codesys directly an iec-code by using the i2c-interface as driver using the codesys ide and st depending on the stepperdriver, used in yöur hat, its possible that an driver is already available in the device-repository. which mcp-device is used on the hat?
Last updated: 2024-03-01

Post by remcoborghuis on C0032 Error to type Pointer to IoConfigParameter ^{CODESYS Forge talk (Post)}
Hi All, I'm using codesys on a raspberry PI. I use V3.5 SP18 Patch 2 development system and codesys for raspberry pi 4.8.0.0. Sometimes when I build the project I get error messages C0007: Expression expected instead of ',' and C0032: Cannot convert type 'Unknow type: '!!!'ERROR'!!!" to type 'POINTER TO IoConfigParameter'. I can't click on the message to bring me to the fault. After I do a "Clean all" the build finishes successful. Anyone who can help me with this problem? Thanks! Remco Borghuis
Last updated: 2024-03-25

Post by dkugler on Codesys SVN ^{CODESYS Forge talk (Post)}
Don't set on SVN. The service phase has started in March 2024 and will be discontinued in 2027. We actually use SVN and have to switch to GIT in the future. As I informed, there is no way of getting a single SVN or GIT licence. I' dont understand, why Codesys forces us customers to pay for an expensive Professional Edition paket from year to year using only one part of it! If you find a way to buy a single licence, let me know.
Last updated: 2024-04-29

Post by rabaggett on CODESYS control for Raspberry Pi 64 SL errors ^{CODESYS Forge talk (Post)}
Update: I started over. I saved progress at each step. all compiled zero errors, zero warnings. Pre-processor messages remain, but I can make progress. Until I try to re- load the project file in Codesys. Re-loaded files error as above when compiled, even though they compiled error-free immediately before saving. Is my installation borked? (Not easy to re-install due to IT madness...)
Last updated: 2024-05-03

Post by totorovic on Softmotion not working with simulation mode ^{CODESYS Forge talk (Post)}
Good morning, I think that the mode Simulation does not support the Softmotion functionnality because it runs the CODESYS process with normal priority wich is not a good thing for real-time behavior. If you want to test your PLC project, please use a Codesys Control Softmotion (and your computer must have the Ethercat driver installed) or much easier, download your code into the C6 Smart. BR
Last updated: 2024-05-13

Post by kris-samoy on Get Alarm status in Codesys ^{CODESYS Forge talk (Post)}
I am rather new to Codesys and I'm trying to figure out how to get the status of an alarm. This to interlock the start of a device until the alarm has been acknowledged... I am not sure if IAlarm.GetState (METH) can be used for this purpose. If yes then could someone please briefly explain how to use this? https://content.helpme-codesys.com/en/libs/AlarmManager/4.1.0.0/Interfaces/pou-IAlarm/GetState.html Thx & grtz, Kris
Last updated: 2024-06-03

Post by sajid on NMEA Serial data read in Control win v3 x64 ^{CODESYS Forge talk (Post)}
I am using the SerialCom example program from the CODESYS website to read NMEA strings in CODESYS Control Win V3 x64 through a serial-to-USB converter. However, I occasionally receive only partial data or encounter errors in the received string. A screenshot of expected NMEA string attached for reference. Could you please advise on how to ensure the full NMEA string is received consistently? Error in strRead variable is <value of="" the="" expression="" cannot="" be="" retrieved=""></value>
Last updated: 2025-10-16

Post by sajid on NMEA Serial data read in Control win v3 x64 ^{CODESYS Forge talk (Post)}
I am using the SerialCom example program from the CODESYS website to read NMEA strings in CODESYS Control Win V3 x64 through a serial-to-USB converter. However, I occasionally receive only partial data or encounter errors in the received string. A screenshot of expected NMEA string attached for reference. Could you please advise on how to ensure the full NMEA string is received consistently? Error in strRead variable is <value of="" the="" expression="" cannot="" be="" retrieved=""></value>
Last updated: 2025-10-16

Post by askic on Generate FBs from source ^{CODESYS Forge talk (Post)}
Hello, I'm coming from Siemens (TIA) world and currently learning Codesys. I'd like to know if there is an option to add external txt file with ST code for creation of a function block and then use this file as a source file from which FB will be generated? For example, in TIA, there is an option add external source file to the project structure and then use option "Generate blocks from source". This would create a FB. Does Codesys have something similar? This external source file would look like this: FUNCTION_BLOCK Scaling VAR_INPUT x, k, n : REAL; END_VAR VAR_OUTPUT y : REAL; END_VAR VAR END_VAR y := k*x+n; END_FUNCTION_BLOCK
Last updated: 2024-07-31

Post by andrebrandt on FB string and naming ^{CODESYS Forge talk (Post)}
Thank you so much. This worked. Waht im trying to do here is to automatically tag each sensors, valves and so on. There is a preatty nasty tag system i working on. "_320" is not alloved. I can have a tag "+4f=320.004-RT001V" In codesys I want to build the FB in folders. -4f | --320 | --001 This is the system structure. Inside here is all of the sensors and so on. But with Codesys, I cannot tag this like this. So what I'm trying to do now is to Make a folder for the building "4f" and one for the system "320", and a POU _001. Is there a way in init to get folder names?
Last updated: 2024-10-01

Post by eaglealex on Length of string and Array of bytes ^{CODESYS Forge talk (Post)}
Hello! I have tried read a file to the string variable. But I faced a problem - there is about 2800 bytes of information in file, but string have a limit 2393 bytes. I made two variables with same address (for automatic convertion) - string[3000] and array of bytes[1..3000]. And I noticed that array of bytes contains all information from file, but string shows only first 2393 bytes. So I have lost information. Is there really such a limitation? Or I have an error in my program and Codesys 2.3 have no limit for such kind of conversation between string and array of bytes? Thank you very much!
Last updated: 2025-04-01

Post by fedex03 on Read Global Variable from an IoT Device ^{CODESYS Forge talk (Post)}
Hello everyone, I am new to the forum, and to programming with CodeSys. I am dealing with IoT device for industry and I should check if a device is able to read/write global variables in an EtherNet/IP Master. Since I do not have an EtherNet/IP PLC, I thought of using CodeSys as a softPLC. I created a program with a set of global variables (GVL) and a task that increments them. I would like to know if I need to enable any options so that the global variables can be read by IoT devices. My device supports Class 2 Class (Explicit Messaging Connection) communication. Thank you in advance for your help.
Last updated: 2025-07-22

Post by mohammadasif on Blink Function definition is wrong in codesys online help ^{CODESYS Forge talk (Post)}
https://content.helpme-codesys.com/en/libs/Util/Current/Signals/BLINK.html in the above link, please correct your website the following: "Output value, starts with FALSE and switches between TRUE and FALSE for the given high and low times" it should actually be: "Output value, starts with TRUE and switches between TRUE and FALSE for the given high and low times" if not please let me know if this has changed in a util library update, in your older website it has the right definition here: https://help.codesys.com/webapp/blink;product=codesys;version=3.5.11.0
Last updated: 2023-12-28

Post by esave on OPC UA Server with on Codesys + OPC UA Client on Labview ^{CODESYS Forge talk (Post)}
Hello everyone I want a communication between my PLC as an OPC UA Server and Labview on my PC as the OPC UA Client. I have an Festo CPX-E-CEC-C1-PN PLC and I have the OPC UA Toolkit from Labview. I created some Variables for testing (see picture 1) on Codesys. I tried to use this Labview block diagram (see picture 2) but I cant connect the PLC to it. What do I have to type in the Server Endpoint URL and what in the Node ID? Is this a good way for communication with a PLC to a PC? If not is there another way?
Last updated: 2024-04-12

Post by wbj0t on connect IDE to plc that uses modem ppp ^{CODESYS Forge talk (Post)}
Hello everyone! I have an PLC device that uses modem ppp connection to the internet with white IP. Device PPP connection with modem operator established, so I can connect to this device via SSH also within Codesys IDE (check version, info, etc...) BUT, I cant establish connection to this device in the device gateway options for application upload and debugging. How can I do this? Im trying set my device remote IP and port 11740, but, as I understand, it is wrong decision, because the next logic in this connection: local W10 service (Codesys Gateway) listen on 1217, then (some how) this service scanning local networks for seeking any local IP which listening on port 11740, and then connects and writes there. OR IM WRONG?:) W10 tool 'Test-NetConnection' with parameters 'ip -Port 11740' succeeded with True. Need some help, please :)
Last updated: 2024-05-21

Post by mborchert on PFC100 Error "Bus not running" ^{CODESYS Forge talk (Post)}
Hello, i currently want to use a wago 750-8102 with the "codesys control for pfc100" runtime. I want to add the devices connected to the internal pfc100 bus via the "search devices" tab. This was reccommended in the following thread: https://forge.codesys.com/forge/talk/Deutsch/thread/7701332199/ But whenever i try to search for devices codesys just doesnt find anything and i cant close the "search devices" window. Has anyone got an idea what the problem might be? I already tried adding the devices connected to the pfc100 manually but the bus just doesn´t start. best regards Moritz
Last updated: 2024-06-17

Post by imdatatas on Error: C0138: No matching 'FB_Init' method found for instantiation of VisuClientObjectMgr ^{CODESYS Forge talk (Post)}
Unfortunately, the "C0138: No matching 'FB_Init" method found" error is a nightmare for CODESYS V3.5 SP21. I'm not sure if anything has been done about this or if anything will be fixed. I've encountered the same issue many times, and it was only resolved by completely uninstalling SP21, deleting all related files and folders from my computer, and then installing SP19. So, I've given up on using SP21 and switched back to SP19patch7. Here are some previous posts regarding the "C0138: No matching 'FB_Init" on SP21 of Codesys. https://forge.codesys.com/forge/talk/Visualization/thread/0763d6ca8e/ https://forge.codesys.com/forge/talk/Motion/thread/9074005bf4/
Last updated: 2025-11-28

Post by kporter on Codesys EtherCAT Driver (CmpEt1000MPD) can't set MAC address ^{CODESYS Forge talk (Post)}
EtherCAT is a point-to-point protocol so it doesn't need a unique MAC address. It would be very useful to set the MAC address to 020000000000, the standard address for this kind of application. (The important bit is the 02 at the start of the address, which means locally-administered MAC.) The stock Windows driver can do this for my i210 card. But the CODESYS CmpEt1000MPD driver cannot. The image shows the setting with the Windows driver. If I set all my customers' cards to this address, then I don't need to deal with this when deploying my application. A simple PowerShell script can be used to set the MAC address once when the NIC is installed and the driver is changed.
Last updated: 2026-02-09

Post by toby on Ethercat Servo Setup ^{CODESYS Forge talk (Post)}
Hi Everyone, I have a simple project with a single servo, but its my first time using Codesys and motion, so I'm a little confused and lost, I've tried to read the tutorial online, but I'm not having much luck sorry. Can I please ask for some pointers. I have a ComfilePi HMI (Raspberry Pi) communicating to a Omron R88D-1SN08H-ECT amplifier. Please see the attached project file (which is better for sharing, the project file, or a archive?). This file was simply for testing the motion of the servo before anything else is tested with it. The project simply rotates the servo 1 rotation when called for, but the speed can vary based on user input. Nothing much fancy. As yet, I haven't had any servo movement, no errors on the amplifier display. How do I link the motion FBs to the physical drive? Thank you very much for any help you can offer. I'm sorry if I'm doing something very stupid or basic and getting it wrong. Have a good day. Toby
Last updated: 2023-09-20

Post by pernockham on Pointer/reference to Codesys trend recording object? ^{CODESYS Forge talk (Post)}
I have a Hmi that acts as an interface for many (mostly identical) units. This is managed by a sort of "mux" where you select which unit that should be presented on the HMI. Backbone is solved by a HMI-gvl defined as reference/pointer to "unit-data", which then can be set to the individual units. While this works for most data I still have not sorted how to solve this for the trend recordings. One solution would be to have already "mux:ed" data values as source for the/one trend. However then the trend would contain data from different units/sources which could/will cause confusion. If its possible to "clear" this can be mitigated. Possibly let the trend have its own "mux-selector" (ie, the hmi are focusing on unit#3 however trend data is locked on unit#5), that could also work.. Or, let each unit have its own trend recording, which is focused if the unit is "selected". Can I reach the trend recording objects programmatically (those defined in the device tree)? Ie, can I use a "reference/pointer to these trend recording objects"? There is a field "data source" in the trend properties dialog which seems to resemble what Im looking for? But Im not sure if I can use it in some way, I cannot change anything in this field it only says <local application="">. </local>
Last updated: 2025-09-16

Sort by relevance or date