Modubus TCP connection affecting EtherCAT running. ^{CODESYS Forge talk (Thread)}
Modubus TCP connection affecting EtherCAT running.
Last updated: 2013-08-25

mobus tcp slave device. read/write holdings with 2 variables. ^{CODESYS Forge talk (Thread)}
mobus tcp slave device. read/write holdings with 2 variables.
Last updated: 2024-03-20

Problem trying Net Base Services 3.5.15.0 TCP connection ^{CODESYS Forge talk (Thread)}
Problem trying Net Base Services 3.5.15.0 TCP connection
Last updated: 2024-10-04

Post by garrian on How to write multiple coils (Modbus FC15) ^{CODESYS Forge talk (Post)}
Thanks for your reply. I belive it is contiguous, I'm writing to adress 0 to 4. Or, do you mean something else? Well, something is happening. If I on the client set adress 1,2,3 to true, only 1 is set to true on the server side. On the client side, the data is array of word. But on the server side, the coils are array of bool. Holding register is array of word on server side. Can this be a problem? Attached screenshot of how it looks at the server side.
Last updated: 2 days ago

Post by thysonfury on OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Post)}
Hi after some assistance with an error on a Groov PR2 PLC. We have a few different communications set up as shown below: One Modbus TCP Slave Connection - ( Sending / Receiving Data from a PC ) Two Modbus TCP Master Connection - ( Reading Data from a UPS Panel and Reading Data Gas Chromatograph) One Modbus RTU Slave Connection 485 - (Reading Data from a fire and gas panel) One Modbus RTU Master Connection 485 - (Sending Data to a Telemetry Unit) All Licenses have been installed as per OPTO22 suggestions of the order below: Modbus TCP Master Modbus TCP Slave Modbus RTU Master Modbus RTU Slave When I check on License manager the RTU Master license seems to disappear on installing the RTU. (What ever reason I’ve been told this is “normal”). If I use Device License Read It will successfully read all the licenses correctly. Now the issue is every 2 hours and between 4. For what ever reason the communications seems to end and lock up for about 20 seconds. During this time even if I was logged into the PLC it would kick me off and I’d have to re type the password to enter. Most of the devices can handle this however the RTU flags up a communications failure at the SCADA and is raising alarms every 2 hours and 4 mins. We’ve had multiple people go through the code to check for anything obvious. Does anyone have any ideas?
Last updated: 2024-04-15

Post by thysonfury on OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Post)}
Hi after some assistance with an error on a Groov PR2 PLC. We have a few different communications set up as shown below: One Modbus TCP Slave Connection - ( Sending / Receiving Data from a PC ) Two Modbus TCP Master Connection - ( Reading Data from a UPS Panel and Reading Data Gas Chromatograph) One Modbus RTU Slave Connection 485 - (Reading Data from a fire and gas panel) One Modbus RTU Master Connection 485 - (Sending Data to a Telemetry Unit) All Licenses have been installed as per OPTO22 suggestions of the order below: Modbus TCP Master Modbus TCP Slave Modbus RTU Master Modbus RTU Slave When I check on License manager the RTU Master license seems to disappear on installing the RTU. (What ever reason I’ve been told this is “normal”). If I use Device License Read It will successfully read all the licenses correctly. Now the issue is every 2 hours and between 4. For what ever reason the communications seems to end and lock up for about 20 seconds. During this time even if I was logged into the PLC it would kick me off and I’d have to re type the password to enter. Most of the devices can handle this however the RTU flags up a communications failure at the SCADA and is raising alarms every 2 hours and 4 mins. We’ve had multiple people go through the code to check for anything obvious. Does anyone have any ideas?
Last updated: 2024-04-15

Post by thysonfury on OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Post)}
Hi after some assistance with an error on a Groov PR2 PLC. We have a few different communications set up as shown below: One Modbus TCP Slave Connection - ( Sending / Receiving Data from a PC ) Two Modbus TCP Master Connection - ( Reading Data from a UPS Panel and Reading Data Gas Chromatograph) One Modbus RTU Slave Connection 485 - (Reading Data from a fire and gas panel) One Modbus RTU Master Connection 485 - (Sending Data to a Telemetry Unit) All Licenses have been installed as per OPTO22 suggestions of the order below: Modbus TCP Master Modbus TCP Slave Modbus RTU Master Modbus RTU Slave When I check on License manager the RTU Master license seems to disappear on installing the RTU. (What ever reason I’ve been told this is “normal”). If I use Device License Read It will successfully read all the licenses correctly. Now the issue is every 2 hours and between 4. For what ever reason the communications seems to end and lock up for about 20 seconds. During this time even if I was logged into the PLC it would kick me off and I’d have to re type the password to enter. Most of the devices can handle this however the RTU flags up a communications failure at the SCADA and is raising alarms every 2 hours and 4 mins. We’ve had multiple people go through the code to check for anything obvious. Does anyone have any ideas?
Last updated: 2024-04-15

Post by joanm on Programmatically change the IP addresses of the Modbus TCP slave devices ^{CODESYS Forge talk (Post)}
Hello all, I am working in a project in which there are multiple Modbus TCP slaves. I need to be able to change the IP addresses of those devices from the HMI and I was planning to use the process depicted here: https://faq.codesys.com/display/CDSFAQ/Modbus+TCP+Slave%3A+Dynamic+Setting+of+the+IP+Address I can see the port number is what is used to specify which slave device we want to modify the IP address of. This said, can I freely set arbitrary port numbers to each device? I mean, can I set the first device to be at port 502, the second one at port 503... Any drawback or restriction? Is there any other way to reference to the device without having to change the port numbers? Thank you all in advance.
Last updated: 2024-01-04

Post by ahuckphin on Issues with Modbus Slave with Raspberry Pi ^{CODESYS Forge talk (Post)}
I have a DFRobot RS485 temperature & humidity sensor (SEN0438) connected to my Raspberry Pi via a USB to RS485 adapter. I am able to connect and read the sensor data when running a python code locally. However in Codesys, I encounter this error "A bus error has occurred." and "There was no response in time". Could this be because of Modbus Server Channel and Modbus Server Init configuration on my part? Admittedly I am new to Codesys. To get to this stage, I: 1. added some lines to CODESYSControl_User.cfg 2. added "Modbus_COM" in Codesys and set "Serial Port Configuration" under "General" 3. added "Modbus_Master_COM_Port" in Codesys and checked transmission mode is set to "RTU" 4. added "Modbus_Slave_COM_Port" in Codesys and checked server address is set to 1 (also set 1 in my sensor) 5. added 1 channel and 1 init for "Modbus_Slave_COM_Port" under "Modbus Server Channel" and "Modbus Server Init"
Last updated: 2024-07-10

Post by installwhat on What is the solution for "Application stopped on recovery switch request"? ^{CODESYS Forge talk (Post)}
<Entry severity="information" component="<10>" user="nobody" timestamp="2024-07-04 ?? 5:10:47" infoId="1">Axis#=121 , Error=30014 , Emergency 2 <Entry severity="information" component="<10>" user="nobody" timestamp="2024-07-04 ?? 5:10:23" infoId="1">TCP Server : WaitClient <Entry severity="information" component="<10>" user="nobody" timestamp="2024-07-04 ?? 5:10:23" infoId="1">TCP Server : Init What is "component="<10>"? Is this system a vanilla CODESYS RTE or is it a modified installation. I think more details are required.
Last updated: 2024-07-08

Post by bfunk on Wago 750-8101 (mit Codesys V3) als Profinet device ^{CODESYS Forge talk (Post)}
Moin, ich habe da ein Problem und komme einfach nicht weiter... Ich moechte eine Wago 750-8101 (mit Codesys V3) zu einem ModBus TCP Slave und einem Profinet slave machen. ModBus habe ich hinbekommen, Profinet bekomme ich einfach nicht hin. habt ihr das evtl. einen hilfreichen Tip fuer mich? Programmiert wird mit Codesys V3.5 SP19 Patch 2 Auf dem Zielsystem (PFC100) ist die Zielsystemversion 4.6.0.0 Das es nicht optimal ist PN und ModBus TCP auf einer Schnittstelle zu haben ist mir bewusst. Wollte aber erstmal ModBus und Profinet zum laufen bekommen bevor ich das Profinet auf die 2. Ethernet-Schnittstelle bringe. /etc/CODESYSControl_User.cfg [SysSocket] Adapter.0.Name="br0" Adapter.0.EnableSetIpAndMask=1 Adapter.1.Name="br1" Adapter.1.EnableSetIpAndMask=1 ist eingetragen. so sieht der Status fuer das PN-device aus. Anbei ein Screenshot.
Last updated: 2024-01-16

Post by tokamk on Dynamic setting of the modbus tcp/ip slave ip address ^{CODESYS Forge talk (Post)}
Hello, I'm working on a project which includes Panel-PC which communicates with a PLC through Modbus TCP/IP. On the PLC I have a CODESYS code which has Modbus slave objects. The Modbus slave objects have to have manually set IP address in order for them to work properly and the Ip address has to be the PC-Panels's IP. This project is going to a customer and they're using their own IP address realm. So, my question is that is it possible to configure these slaves in some other way, so that the customer doesn't need to modify the CODESYS project? I was thinking that would it be possible to set the IP address of these slaves from external source?
Last updated: 2024-02-15

Post by wbj0t on Global variable access by Programms and Modbus Devices (attach device to bus) ^{CODESYS Forge talk (Post)}
Hi everyone. I use Raspberry Pi 4, one core codesys SL. I have a question about global variable access via programm when I glued the same variable to MODBUS SERIAL/TCP DEVICE holding register. So, the question: what behavior of this modifying? When I set "Always update variables (in bus cycle)" and set some task as bus for the Device, then in another task I cant change this varible (can, but immediatly the old value setted again). But the same things works with MODBUS SLAVE: again "Always update..." and master attached to some task, then I change variable in another task and all works. I cant set up my variables from retains file at PrepareStart event because of this behavior with MODBUS SERIAL/TCP DEVICE. Thanks, wbj0t.
Last updated: 2024-07-18

Post by ofey on Device parameter - ‘ModbusTCP Configuration’ ^{CODESYS Forge talk (Post)}
Hi! Do anybody know how I can add and enable the parameter 'Default Modbus TCP slave' on a device? I am currently writing a program where the PLC shall be set up as a Modbus TCP client, but I dont know how to add parameters to devices in codesys. I'm pretty new to the codesys environment. The picture in the attachment is on a similar PLC project where I have not written the code. my goal is to add this parameter in another project.
Last updated: 2023-10-04

Post by winki on Modbus TCP Client ^{CODESYS Forge talk (Post)}
Hello, I am new on CODESYS env. I would like to do some Modbus TCP, but I am wondering If using codesys you must use the device "Modbus_TCP_Client" & "Modbus_TCP_Server". I would like to do it without device, only using ST. Is that possible ? I try the example : MODBUS_master_example, but it is not working. If it is possible to dot it without any Device I will show my code. Thx a lot
Last updated: 2024-10-25

Post by nano on Modbus TCP/IP slave communication errow ^{CODESYS Forge talk (Post)}
please tell us the exact error message from diagnostic. U can view it at devicetree in the node-element diagnostic from modbus-configuration. u also can activate the function auto-reconnect in master and increase a little bit the timeout and the repetition to male thw communication a little bit more robust
Last updated: 2024-02-04

Post by oymyakon on Modbus Lockup ^{CODESYS Forge talk (Post)}
Hi i have a project where i am communicating with many modbus devices using TCP to serial. This is all working extremely well except when i turn one of the remote devices off. If i leave the auto reconnect on it still doesn't talk to the rmianing devices and if i turn Auto reconnect off it locks up. Any help would be appreciated. Paul.
Last updated: 2024-08-07

Post by oymyakon on Modbus Lockup ^{CODESYS Forge talk (Post)}
Hi i have a project where i am communicating with many modbus devices using TCP to serial. This is all working extremely well except when i turn one of the remote devices off. If i leave the auto reconnect on it still doesn't talk to the rmianing devices and if i turn Auto reconnect off it locks up. Any help would be appreciated. Paul.
Last updated: 2024-08-07

Connect Client Codesys With Server Java ^{CODESYS Forge talk (Thread)}
Connect Client Codesys With Server Java
Last updated: 2023-08-17

Security Screen - Custom Certificates for OPC UA Server? ^{CODESYS Forge talk (Thread)}
Security Screen - Custom Certificates for OPC UA Server?
Last updated: 2023-08-23

OPC UA Server limitations, large array crashes runtime ^{CODESYS Forge talk (Thread)}
OPC UA Server limitations, large array crashes runtime
Last updated: 2023-08-23

CODESYS Automation Server Connector for 3.5 SP11 ^{CODESYS Forge talk (Thread)}
CODESYS Automation Server Connector for 3.5 SP11
Last updated: 2023-08-30

Download Missing Libraries failed, Apache server HTTPS protocol ^{CODESYS Forge talk (Thread)}
Download Missing Libraries failed, Apache server HTTPS protocol
Last updated: 2020-09-23

Log in to remote PLC via Automation Server ^{CODESYS Forge talk (Thread)}
Log in to remote PLC via Automation Server
Last updated: 2020-09-29

Codesys Soft PLC connection to TOP OPC UA- Server ^{CODESYS Forge talk (Thread)}
Codesys Soft PLC connection to TOP OPC UA- Server
Last updated: 2021-03-22

Sort by relevance or date