Post by mariussandu on OPC-UA
CODESYS Forge
talk
(Post)
Hello, I am experiencing an intermittent OPC UA server issue on CODESYS Control for Raspberry Pi SL 4.21.0.0. Runtime information: codesyscontrol 4.21.0.0 Raspberry Pi 4 Model B Rev 1.1 - 4Gb OPC UA Server: CmpOPCUAServer 3.5.22.x Server IP: 192.168.0.110 OPC UA endpoint: opc.tcp://192.168.0.110:4840 The main OPC UA client is Node-RED running on 192.168.0.111. This has an active subscription with some tags and also some write functions active. The system normally works correctly for a period, but at some time the OPC UA communication stopped. Node-RED started reconnecting continuously but could not reconnect. I also tried connecting using UaExpert, but UaExpert returned: BadTimeout At the same time, the PLC application itself was still running. Before restarting CODESYS, I captured the TCP connections. The OPC UA server was still listening: tcp 11 0 192.168.0.110:4840 0.0.0.0:* LISTEN However, there were many connections from the Node-RED client stuck in CLOSE_WAIT: 192.168.0.110:4840 192.168.0.111:45008 CLOSE_WAIT 192.168.0.110:4840 192.168.0.111:53678 CLOSE_WAIT 192.168.0.110:4840 192.168.0.111:44032 CLOSE_WAIT 192.168.0.110:4840 192.168.0.111:36612 CLOSE_WAIT 192.168.0.110:4840 192.168.0.111:45012 CLOSE_WAIT 192.168.0.110:4840 192.168.0.111:36592 CLOSE_WAIT ... Some of these sockets also had data remaining in Recv-Q, for example: Recv-Q = 61 Recv-Q = 121 There were roughly 15–20 OPC UA connections in CLOSE_WAIT. Restarting only the CODESYS runtime immediately restored OPC UA communication. After restart: LISTEN 0 10 192.168.0.110:4840 and both Node-RED and UaExpert can connect normally again. There are no obvious OPC UA errors during startup or in log. On RPI 2 I had a memory leak regarding OPCUA so I had to upgrade to RPI4. What can I do in this case? Thank you!
Last updated: 2026-08-26
Post by robinep on PM564 online problem
CODESYS Forge
talk
(Post)
Hi I'm beginner in codesys There is a PM564 ABB Plc in a machine and I am going to upload plc program The connection with plc is established with tk503, Codesys is online and show plc status, How can I upload the program in PLC? I don't have any source code. regards
Last updated: 2026-09-26
Post by timvh on Legacy IFM CANopen I/O modules with CR710S / CODESYS 3.5
CODESYS Forge
talk
(Post)
I don't work for IFM, nor for CODESYS and didn't create the .eds file or developed the CAN protocol. I have no knowledge of the exact contents and SDO's or PDO's which are exchanged. So no, I am not sure. But if the .eds file confirms to the CANopen specifications, why shouldn't it?
Last updated: 2026-10-02
Post by dmb-fan on Nach "Alles Bereinigen" viele unklare Fehler, aber nur in Schrittketten
CODESYS Forge
talk
(Post)
Offiziele CoDeSys Rückmeldung: Der Fehler ist bekannt und erfasst mit SFC-224 SFC with parallel branch without name is no more compilable. Das ist ein Accident zu 4.5.0.0. Lösung ist also entweder: Downgrade auf SFC 4.4.0.0 oder Vergabe von Namen für die parallelen Zweige
Last updated: 2026-10-19
Post by kaotic2499 on Upgraded Raspberry 2b to Raspberry 5, Trends Broken?
CODESYS Forge
talk
(Post)
There is currently a bug with the Raspberry Pi 64 SL where it is unable to Trend Global Retain or PersistantVars. The work around is to use standard Global Variables for Trend Data. This will be patched by Codesys in the near future reference "VIS-6170"
Last updated: 2025-11-13
Post by kalmeyer on STEPPER CODESYS SOFTMOTION_DRIVE
CODESYS Forge
talk
(Post)
Hello everyone I have been trying to solve this problem for a long time. Please help me..... I have browsed: https://forge.codesys.com/drv/sm3raspistepper/home/Home/ and it says under "IMPLIMENTATION" that I have to create a POU with the text to be able to use: MC_Power or MC_MoveVelocity How do I write it into the CODESYS program? Thanks in advance /Klaus Kalmeyer
Last updated: 2025-11-17
Post by yohayr on Access Violation sherd memory
CODESYS Forge
talk
(Post)
Hi, once in a while I get an Access Violation exception in Sherd memory pointer. the strange thing is that I protect the pointer dereference and I get this exception 1 line after the protection. I added photos of the exception can someone tell me what is that about?
Last updated: 2025-11-25
Post by yohayr on Access Violation sherd memory
CODESYS Forge
talk
(Post)
Hi, once in a while I get an Access Violation exception in Sherd memory pointer. the strange thing is that I protect the pointer dereference and I get this exception 1 line after the protection. I added photos of the exception can someone tell me what is that about?
Last updated: 2025-11-25
Post by bertram on Installation IOT Libraries kann nicht installiert werden
CODESYS Forge
talk
(Post)
IOT Package SL 1.12.0.0 läst sich nicht Installieren da keine Installation gefunden wurde in die die das Package installiert werden kann. Windoof 11 Installer 2.5.0 Codesys V3.5 SP21 Patch 3+ 64 Bit. Hat jemand einen Rat für mich ? Bin um jeden Tip dankbar. herzliche Grüße an alle.
Last updated: 2025-11-25
Post by worker69 on Alarmgruppenvorlage kann über Kontextmenü keine weitere Latch Variable hinzugefügt werden
CODESYS Forge
talk
(Post)
Hallo, ich habe das problem, dass ich in einer Alarmgruppenvorlage keine wietere LATCh Variable hinzufügen kann. Wenn ich dies über das Kontextmenü versuche, dann erscheint folgende Fehlermeldung "Der Objektverweis wurde nicht auf eine Objektinstanz festgelegt". Ich verwende Codesys V3.5.19 P0 und 23.5.19 P7 Was mache ich falsch
Last updated: 2026-01-05
Post by alexgooi on Codesys KNX implementation
CODESYS Forge
talk
(Post)
Dear forum, We are currently doing some research on the Codesys KNX implementation (https://store.codesys.com/en/codesys-knx-sl.html). We almost have it working but we are missing the last part. The setup: We have a Codesys virtual control container running on docker (4.17.0.0), the I/O is running over an Ethernet IP coupler (Weidmüller), and this is running fine. As far as I’m concerned this tells me that the ethernet device is working properly (the container has access to the outside world, including multicast). Underneath this ethernet adapter the KNX module is added (see picture). In the KNX device (Codesys) 2 input variables are added (see picture), and these are exported to ETS (ETS 5). In ETS A Codesys KNX device has been imported and the Codesys export was imported, afterwards the group addresses are attached to the variables (see picture). Afterwards this configuration is downloaded to the Codesys controller (Container) via ETS. ETS asks for the pressing of the programming button, when the virtual programming button is pressed the download starts and finishes without any errors. This tells me that ETS is communicating with the Codesys controller, and that the download process is ok (so far so good). Now the part where we are struggling with, somehow we need to convert the KNX TP to KNX IP. For this we have the following interface: Zenio KIPI SC (https://www.zennio.com/product/kipi-sc/) this is a KNX TP to IP interface. We have the following setup for this device (see picture) (an IP in the same subnet is used). We tried multiple combinations of IP addresses but the TP devices are simply not communicating to the Codesys container. Does anyone has any advice on what to try next. To make the question more explicit how can we link the TP bus to the Codesys device? Kind Regards Alex
Last updated: 2026-01-05
Post by osande on Trend/trace data
CODESYS Forge
talk
(Post)
Ok, the problem is that the trend/trace system can't read function block instance data. The variables has to be stored directly under the program calling the FBs. Thus, FB variables to be trended/traced must be connected to variables declared in the program. Seems like a bug to me!
Last updated: 2026-03-13
Post by bdschnapp on OPC-UA ApplicationUri / ProductUri
CODESYS Forge
talk
(Post)
From Codesys support: The format of the URN is always the same. It's always urn:<vendor>:<product>:OPCUA:Server. What I think you can influence the vendor and product (DeviceName) through settings in the runtime cfg file:</product></vendor> [SysTarget] VendorNameUnicode="T\00E\00S\00T\00" DeviceNameUnicode="t\00e\00s\00t\00" Note that these are 16-bit strings, thus the ASCII padded with nulls
Last updated: 2026-03-17
Post by dat422 on OPC UA Enum Issue
CODESYS Forge
talk
(Post)
Hi everyone, I’m using CODESYS V3.5 SP22 with the Communication Manager to run an OPC UA server. I have a problem with enums: when I view them in a client like UaExpert, only the last enum member is shown, and it has the wrong value. Has anyone seen this issue before or knows what might cause it? Thanks!
Last updated: 2026-03-27
Post by nulltrace on Modbus TCP Server connection is ESTABLISHED but all holding registers are value 0?
CODESYS Forge
talk
(Post)
your case looks different, the first one was an codesys modbus tcp-slave, your's an Master-Application with gateway. I dont know this Unit, but i would say, from Point of Codesys it looks wrong configured. Just give us more detailed configuration and the please make a sketch of the topology you're trying to realise.
Last updated: 2026-04-08
Post by alexgooi on No Bootproject possible
CODESYS Forge
talk
(Post)
Hello Simon, Thank you for your response. The problem occurs after about 10 online changes, after this a full download is required, but that means that the installation is going down. Is it possible to enlarge the space reserved for online changes, so that the problem occurs after 100 online changes for example? Kind regards Alex
Last updated: 2026-04-14
Post by alexgooi on Network variable stops sending
CODESYS Forge
talk
(Post)
Are you making use of structs in the NVL? In the past I had similar behavior (NVL stops sending) when I added something in the struct. if you are making use of structs makes sure that the structs are identical in both projects. If this is not the case, have you tried changing the port number to something different than 1202?
Last updated: 2026-04-29
Post by cd-tt on cannot connect ot linux runtime: device does not answer the scanrequest
CODESYS Forge
talk
(Post)
thank you eschwellinger. That one solved it for me. The password must have a length of at least 8 characters. The password must consist of at least 4 different characters. The password must contain lowercase letters. The password must contain uppercase letters. The password must contain digits. The password must contain special characters.
Last updated: 2026-06-12
Post by repc2026 on Codesys MODBUS RTU devices
CODESYS Forge
talk
(Post)
I am trying to use Codesys to connect by Modbus RTU to an Arduino UNO, I add the Modbus COM Port but when I try to add the master and the slave I don't have these options, I attach an image of the device manager. I am using Codesys 3.5 SP21.
Last updated: 2026-07-13
Post by timvh on PROFINET Controller SL: WRREC remains BUSY forever, no DCE/RPC packets transmitted (RevPi Connect 5 + NORD SK205E)
CODESYS Forge
talk
(Post)
A customer of us had the same issue. They updated (at that time) to CODESYS 3.5.21.50 and Control for Linux SL versie 4.19.0.0. After that they couldn't reproduce the issue anymore. You might give this a try too.
Last updated: 2026-07-21
Post by wold on CodeMeter Network Server: Keep runtime dongle local-only and export only a second CmStick
CODESYS Forge
talk
(Post)
Hello, I am running a CODESYS Control Runtime on a Raspberry Pi. Two CmSticks are connected to the same system: CmStick A - Runtime license - MultiCore license - KNX license CmStick B - Engineering / Developer licenses My goal is: The runtime on the Raspberry Pi shall use CmStick A locally. Licenses from CmStick A shall NOT be provided by the CodeMeter Network Server. Only licenses from CmStick B shall be available to remote network clients. During troubleshooting I observed that the CodeMeter Network Server collects licenses from both CmSticks. The KNX license appears to be local-only, but the runtime and multicore licenses of the same dongle are still visible through the server. I would like to know if a supported configuration exists for the following scenario: One CmStick remains strictly local to the runtime. A second CmStick on the same machine is exported through the CodeMeter Network Server. Questions: Is it possible to exclude a specific CmStick from being exported by the CodeMeter Network Server? Can this be configured via License Access Permissions (ACL), WebAdmin, or another mechanism? Can export rules be applied per CmStick, per Firm Code, or per Product Code? If supported, could you provide a configuration example or a reference to the relevant documentation? The reason for asking is that after removing a separately installed CodeMeter server component and returning to a local-only setup, the runtime licensing behaviour became stable again. Therefore I am looking for the officially supported way to keep the runtime dongle local while still providing engineering licenses from a second dongle over the network. Thank you.
Last updated: 2026-08-02
Post by automa on SBOM
CODESYS Forge
talk
(Post)
Hi, How do you create your SBOM in Codesys. I have been searching for this topic but couldn't find any useful information. I am referring to making an exported list of all libraries used in the project. I have developed a python script that exports them, but I am open for ideas of beast practice
Last updated: 2026-08-21
Post by antonz on Could not write options file at...
CODESYS Forge
talk
(Post)
I ran into a similar issue, albeit not the exact same conditions nor the same file if I recall correctly. As a workaround I have used an elevated account to give my regular user account write access to the specific directory where the failure occurred. It is not pretty and I am not happy with it. It does work.
Last updated: 2026-09-07
Post by ilarioimi on Date Picker
CODESYS Forge
talk
(Post)
Hello, I am new here and need some help. I have added the Date Picker to a visualization page. The date selection works, but the current day is not highlighted. The date and time are displayed correctly by the system, which is set by default to “VisuElems.Visu_DateTime.DisplayUTC:= FALSE;”. Is there some project setting or Visualization Manager setting that I am missing? Thank you. Ilario.
Last updated: 2026-01-14
Post by schelchpaul on Problem with missing content in Dialog Windows in Win11
CODESYS Forge
talk
(Post)
Hello, i have the big Problem that dialog windows in Codesys 2.3 are cut off, as seen in the attached screenshots. I've tried to adjust the screen resolution, i tried changing scaling, i tried the compatibility options. To keep it short, nothing worked. If someone already had that problem and knows a fix, please answer.![]
Last updated: 2026-01-14
To search for an exact phrase, put it in quotes. Example: "getting started docs"
To exclude a word or phrase, put a dash in front of it. Example: docs -help
To search on specific fields, use these field names instead of a general text search. You can group with AND or OR.