Post by mmpl on CAA Library Function ^{CODESYS Forge talk (Post)}
I want to change date and time format. I am using CAA storage library function. I am not receiving any value in to output.
Last updated: 2024-04-16

Post by micik on "CAA" meaning in library names ^{CODESYS Forge talk (Post)}
Hello, what CAA stands for? Since it is a collection of different libraries, does it mean it is created by some specific organization? Thanks!
Last updated: 2024-05-31

Post by timvh on CanOpen write issue ^{CODESYS Forge talk (Post)}
See: https://content.helpme-codesys.com/en/CODESYS%20Examples/_ex_canopen_canopen.html SDO example: SegmentedAndBlockWriteExample: Writing if an object of any length via SDO (segmented transfer or block transfer) by means of CiA405.SDO_WRITE_DATA This help page also contains a link to a demo project.
Last updated: 2024-07-16

Post by damian177 on Codesys V3.5 + Pixtend v1.3 + RaspberryPi ^{CODESYS Forge talk (Post)}
I solved my problem by adding CAA DTUtil Extern library. Now works.!
Last updated: 2023-09-28

Post by kislov on Converting UINT into bytes and converting 2Bytes into UINT ^{CODESYS Forge talk (Post)}
https://content.helpme-codesys.com/en/libs/CAA%20Memory/Current/CAA_Memory/Packing/PackBytesToWord.html + optional TO_UINT
Last updated: 2023-12-08

Post by micik on CAA File- FILE_OPERATION_DENIED error ^{CODESYS Forge talk (Post)}
Thank you wollview, it is clear now, it is due to security reasons that access to the file system is restricted.
Last updated: 2024-05-16

Post by kislov on "CAA" meaning in library names ^{CODESYS Forge talk (Post)}
CODESYS Automation Alliance I doubt that this organization still exists in any form.
Last updated: 2024-05-31

Post by sawicpx on CANbus Remapping PDOs During Runtime ^{CODESYS Forge talk (Post)}
Hello, I am working on an application where I need to remap PDOs to a different CANopen object during runtime depending on what value is at a specific register. I have gotten to the point where I put the device into Preoperational State using the CIA405.NMT function. I then reconfigure the PDO 180x and 1a0x obejcts usings SDOs to point to a new canopen object on the device however when I go to restart the Device from PREOP to OP using the CIA405.NMT function the device is reset back to the original configuration as per the initial setup. I am wondering is there any way to change the PDOs at runtime is there some more functionaility I can access to do this. Any direction is appreciated!
Last updated: 2023-12-22

Post by pazderai on CanOpen write issue ^{CODESYS Forge talk (Post)}
Thank you for an answer. Unfortunatelly, it doesn't work. The slave needs command byte as follows 0x22. It means expedited transfer where s-bit is not set, therefore data length is not specified. If I use segmented mode by CiA405.SDO_WRITE_DATA it produce command byte as follows 0x21 which is unfortunately supported by the slave and it returns with error 0x05040001 - SDO Abort Code -Client/server command specifier not valid or unknown. I can use CAN API low level to overcome this problem where it is possible to set 0x22 as a command byte, but than I can use user interface to set the communication probably, because I thing that machine expert uses library CiA405.SDO_WRITE for setting the slave. Or am I wrong?
Last updated: 2024-07-16

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi everybody We are currently working on a project with an RS232 serial COM interface and using the CAA SerialCOM library. We have it working fine reading and writing data, although we have found an issue we cannot resolve and any suggestions would be helpful. We have noticed that after a while the RS232 stops working. We have tracked this down to the HANDLE hCom keeps increasing and when this reaches 1023 the COM returns an unknown error "5003". Is there a way to reset this hCom reference? Thanks Richard
Last updated: 2024-03-22

Post by naps on Welchen I-Port benötige ich? ^{CODESYS Forge talk (Post)}
Hallo, ich versuche eine 750-653(konfiguriert per iocheck) über die Wago Modbus Lib einzusetzen. Ich scheitere im moment an dem Korrekten I-Port. Ich habe es mit 75x_653 und IoConfig_Globals.75x653 versucht, jedoch bekomme ich folgenden fehler: ------ Übersetzungslauf gestartet: Applikation: Device.Application ------- Code typisieren... Code erzeugen... [FEHLER] Unbenannt7: POU_1 Device: SPS-Logik: Application: C0032: Typ 'DED.CAADiagDeviceDefault(caa device diagnosis, 3.5.20.0 (caa technical workgroup))' kann nicht in Typ 'WagoTypesCom.I_WagoSysComBase(wagotypescom, 1.6.2.3 (wago))' konvertiert werden Übersetzung abgeschlossen -- 1 Fehler, 0 Warnungen : Kein Download möglich Wie kann ich den die Karte benutzen?
Last updated: 2024-10-01

Post by fleaplc on FILE_OPERATION_DENIED ^{CODESYS Forge talk (Post)}
By using the CAA FILE library (FB FILE.Open) (raspberry pi, codesys 3.5.19.0) I always get the error FILE_OPERATION_DENIED The file exist, it has r/w/x access and path is correct... Some idea to fix it?
Last updated: 2023-09-25

Post by baldeep on Codesys Raspberry Runtime 4.10.0.0 and RSM Utility 3.5.19.0 ^{CODESYS Forge talk (Post)}
I had been using Codesys Raspberry 4.9.0.0 Runtime for a Project with CAA File 3.5.19.0. But now with Update 4.10.0.0 and Raspberry pi 64 Bit.....i cannot compile my code as RSM Utility 3.5.19.0 is not recognised. Any help? Regards
Last updated: 2023-11-20

Post by timvh on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
You should only open de COM port once and then leave it open. This hCom should not keep on incrementing. (off course when you are done communicating, you need to close the COM port)
Last updated: 2024-03-22

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by micik on Reverse bytes in an array ^{CODESYS Forge talk (Post)}
Hello, I'm getting the data in Codesys that is an array of 8 bytes. From this array, I need to foram LREAL number, however, because of different endiannes I need to reverse bytes in this array and then copy to a LREAL variable. For this I'm using a loop and it works OK. I wonder if there is a built in function to do this. I have found CAA Memory library but it has functions like reverse bytes in DWORD. But it seems it doesn't have what I need. https://content.helpme-codesys.com/en/libs/CAA%20Memory/Current/CAA_Memory/Reverse-Bit-Swap-ByteWord-order/ReverseBYTEsInDWORD.html What I need is a function to reverse bytes in an 8 byte array, or something similar.
Last updated: 2024-08-22

Post by micik on Reverse bytes in an array ^{CODESYS Forge talk (Post)}
Hello, I'm getting the data in Codesys that is an array of 8 bytes. From this array, I need to foram LREAL number, however, because of different endiannes I need to reverse bytes in this array and then copy to a LREAL variable. For this I'm using a loop and it works OK. I wonder if there is a built in function to do this. I have found CAA Memory library but it has functions like reverse bytes in DWORD. But it seems it doesn't have what I need. https://content.helpme-codesys.com/en/libs/CAA%20Memory/Current/CAA_Memory/Reverse-Bit-Swap-ByteWord-order/ReverseBYTEsInDWORD.html What I need is a function to reverse bytes in an 8 byte array, or something similar.
Last updated: 2024-08-22

Post by laruso on Runtime device Enable/Disable procedure ^{CODESYS Forge talk (Post)}
I implemented the parts from the CAA Device Diagnosis Example.project and could use it for switching on and off, the CAN devices that were located under the CANbus and CANopen_Manager. But i can't do the same with I2C_master_test_version or devices below this one. In the example project there is only the EtherCAT Master, CANbus and CANopen_Manager, and Ethernet with devices below.
Last updated: 2023-10-27

Sort by relevance or date