Post by danielbeers on Automation Server + Pi Gateway + PLC w/ CAN ^{CODESYS Forge talk (Post)}
Hello, I have a project using some EPEC PLC's. Some of them are programmable using Ethernet and some use CAN. We currently have a Raspberry Pi that is acting as a gateway to the Codesys Automation Server and is successfully working for the PLC's communicating over ethernet. I am trying to achieve a similar result for the PLC's that have only CAN access. I have PEAKCan drivers on the Pi, and can successfully send/receive messages. But the Gateway does not recognise the PLC when scanned from the Automation server online. Is there a library or service that exists to translate the CAN messaging, to the Edge Gateway, and be able to achieve remote access with the Automation Server? Or is this not possible without creating something custom? Cheers, Daniel
Last updated: 2024-09-22

Post by pernockham on Linking to IO during runtime with hot swap? ^{CODESYS Forge talk (Post)}
I have a project where a single PLC shall control multiple nodes (up to 10 units?) with IO connected through profinet. Ideally each node should be identical however with time I see situations were different setups/configurations will be used. Codesys PLC (GVLs) |Profinet | |--PNIO-node-1--| | | AIO, | | DIO, | | CNT etc. | |--PNIO-node-2--| | | AIO, | | DIO, | | CNT etc. Ideally I think of a configuration through yaml/xml-files (the assignment/linking of the profinet nodes towards GVL-variables in the PLC as well as scaling, channel configration etc.). Would be grateful if someone could suggest library/-ies that can handle the following: - Verify what IO is connected to a device/node. - Hot-swap/assign link for IO towards GVLs, either automatically or through a HMI.
Last updated: 2024-10-11

Post by dsa28 on OPC UA subscriber not operational ^{CODESYS Forge talk (Post)}
Hello All, Hopefully I can get some help configuring an OPC UA subscriber in a CODESYS runtime in a Raspberry Pi 5 that tries to retrieve data from an OPC UA publisher (in this case running in a TwinCAT system). I tried to follow the steps described in the page to implement the OPC UA subscriber: https://content.helpme-codesys.com/en/CODESYS%20Examples/_ex_opcua_pubsub.html Seems that the example provided was created with version 3.5.16.0. Now with version 3.5.20.20 is not possible to open the complete project neither convert it. Anyway, after configuring all IPs and ports used in the OPC UA connection function block but the connection state always shows DISABLED. Can someone help me to do the proper configuration of the OPC UA subscriber? Many thanks in advance.
Last updated: 2024-10-22

Post by xabier on BUG CODESYS-NO WORK AUTOMATICALLY RESTARSLAVES ^{CODESYS Forge talk (Post)}
I detect a Bug of Codesys....NO WORK AUTOMATICALLY RESTARSLAVES. I explain the secuence: I have click in my project the option AUTOMATICALLY RESTARSLAVES In the moment start my Ipc, the network ethercat start correctly I disconnect the wire of my first slave and later connect again the wire..(see the screen Bug Codesys restart slave1) NO work the restart automatic slaves...and is not possible execute of FB MC_REset beacuause appear this error (see the screen Bug Codesys restart slave2) The only way for resolver this problem is execute the FB SMC3ReinitDrive I replay the same with PLC BECKHOFF in Twincat3 and I havent this problem...In the moment connect the wire again in the slave the comunication of ehterCat restart and the slave comunication again with out problem
Last updated: 2024-11-07

Post by bertcom on Converting each character to a string into ASCII ^{CODESYS Forge talk (Post)}
Good afternoon, I have a project where i need to split a string and send it in ascii code to an Domino Printer. Concept: i get an String from an Zebra scanner looking like this : " R002043;5410761402862;Oil Plus 2C Comp.A - Gris Belge;1286193824;" To start is the ";" the seperator. i found some functions to delete the ";" in a string. this is okay but now i want to convert each digit in the string into ascii like this: R=82 0=48 0=48 2=50 0=48 ... This because the printer wants to receive a string like this: <esc>OQ001TE 82 48 48 50 48 ...<eot></eot></esc> Anyone who can help me with setting me on the right track with some advice?
Last updated: 2024-11-08

Post by bertcom on Converting each character to a string into ASCII ^{CODESYS Forge talk (Post)}
Good afternoon, I have a project where i need to split a string and send it in ascii code to an Domino Printer. Concept: i get an String from an Zebra scanner looking like this : " R002043;5410761402862;Oil Plus 2C Comp.A - Gris Belge;1286193824;" To start is the ";" the seperator. i found some functions to delete the ";" in a string. this is okay but now i want to convert each digit in the string into ascii like this: R=82 0=48 0=48 2=50 0=48 ... This because the printer wants to receive a string like this: <esc>OQ001TE 82 48 48 50 48 ...<eot></eot></esc> Anyone who can help me with setting me on the right track with some advice?
Last updated: 2024-11-08

Post by pistola on Visualization Size - Set Layout ^{CODESYS Forge talk (Post)}
I feel like this is a setting issue and I can't seem to find the right setting. I have a new project that I'm looking to add visualizations to however when I select my template size (1280 x 800) I make sure in my properties under the visualization tab, I have "Use specified visualization size" selected and my width set at 1280 and height set at 800. Now within my visualization editor I can't see to get the size outside of my template to grey out. I've attached a PDF showing what I'd like the visualization editor to look like and what mine currently looks like. Any help would be greatly appreciated.
Last updated: 2024-11-12

Post by simone on Collapse all ^{CODESYS Forge talk (Post)}
Hi, I'm wondering if it exist a button or a keyboard shortcut (much much better) for "collapse all" the open folder on a codesys project. It would really be nice to have. Also: Are there some options or configuration for set a default zoom for the different editor (or even one global), for example I would like to have 100% on ST, LD editor and have 80% on Visualization Editor; and also have a button to set all the zooms to default, now it seems that every file mantain the one previously set. I'm working with the 3.5.20.10 right now Thanks!
Last updated: 2024-11-21

Post by kevinrn on Github Actions CI/CD tasks - development topic ^{CODESYS Forge talk (Post)}
Hi @steven-schalm, Thank you for your inquiry, and I apologize for the delayed response! We use GitHub Actions cloud runners for this purpose, as it eliminates the need to maintain our own build runners. You can get started by creating a free GitHub account, which includes complimentary minutes for running actions on Windows runners. You can find an example implementation in our repository: https://github.com/powerIO-GmbH/action-codesys-setup I'm currently working on making additional features public, including: Git checkout functionality, Code signing, Custom script execution However, these additions require some preparation before release. Feel free to contribute to the project! BTW: You can also execute this locally, even the yml files with nektos/act on your windows dev machine.
Last updated: 2024-11-27

Post by imdatatas on MC_CamIn did not work properly with SMC_FreeEncoder on SoftMotion 4.17.0.0 ^{CODESYS Forge talk (Post)}
Hi @tk096, Thank you for your response. Here is example project file and some screenshot for your analysis regarding this matter. In order to reproduce the problem on your side and make it independent of the hardware, I simulated the encoder counter incrementally for the master in this example. I configured a virtual axis as the slave motion axis. The problem occurs in the same way in the real hardware configuration (servo drive connected to Ethercat and hardware incremental encoder) in MC_CamIn. I hope this example helps you see the problem on your side and understand and find the source of the problem with FreeEncoderAxis for Softmotion 4.17.0.0. Best Regards, Imdat
Last updated: 2024-12-19

Post by sigurdrb on Read codesys version in the codesys application ^{CODESYS Forge talk (Post)}
Hi! I want to read the codesys version into the project, so I can highlight it in the SCADA system. VAR dwVersion : DWORD; END_VAR SysTarget.SysTargetGetVersion(pulVersion := ADR(dwVersion)); This gives me the value 100859909. I tried to search ths up and found som older post (https://forge.codesys.com/forge/talk/Runtime/thread/a55981ff4d/) that said each 4 bytes reads a number in the version. Example is 50662666 = 16#03050D0A which reads to V3.5.13.10 When I run this code I get the value 100859909, which I cant translate to anything meaningful. I am running it on Codesys V3.5.19.70. Help appreciated!
Last updated: 2025-01-17

Post by tyleretn on Codesys 3.5 SP18 P4 Freezing on Library Update ^{CODESYS Forge talk (Post)}
I have created a library with both code and visualizations to be used in multiple other projects. After I update the library version into the library repository, I have much difficulty updating the version into the main project. I can always update the library version in the Library Manager just fine. My issue, is sometimes Codesys will freeze when opening the visualization that uses the library visualizations. Sometimes it opens, but freezes when I try to access the library visualizations from the Visualization Toolbox. I try letting Codesys run for upwards of 4+ hours and it is stuck in this state. On very rare cases I have no issues and can continue with my work. I haven't found a consistent reason or work around. Has anyone else had this happen?
Last updated: 2025-02-27

Post by alberto on ExportPLCopenXML is failing ^{CODESYS Forge talk (Post)}
I'm trying to export my whole project through the option ExportPLCopenXML. It seems working, but when I'm trying to import the xml I have the following error during the importation process: Object reference not set to an instance of an object. It seems a usual issue with this process that affects to the pointer to user classes inside a procedure. I receive this error for two general functions that have this pointer declarations in the VAR_INPUT section. It seems a bug into the export/import process of CodeSYS and I couldn't skip it so far. Anyone could help me? Thanks in advance.
Last updated: 2025-03-15

Post by r-c-r on SM3RaspiStepper 0.0.0.6 issue ^{CODESYS Forge talk (Post)}
Hello, I noticed that version 0.0.0.6 is now available, so I tested it using CODESYS V3.5 SP19 Patch 7 and SoftMotion 4.17.0.0. While the project compiles and downloads without issues, I encountered a problem with the 'Enable: GPIO pin number that is set when the axis is enabled (with MC_Power) (0: not used)' functionality — it no longer works (HIGH level not present at the output pin). I observed the same behavior with version 0.0.0.5, whereas version 0.0.0.4 functions correctly. Could you help me identify what might be causing this issue or suggest how to resolve it? Thanks.
Last updated: 2025-03-19

Post by agentcousto on [Bug report] Issue with Importing XML Files Containing "POINTER TO" Variables in Codesys Platform Plugins Versions 2.7 and 2.8 ^{CODESYS Forge talk (Post)}
Hello, I have developed a Python script that I run to import XML files into my project. For this, I use the Python function import_xml(). Everything was working fine when I was using Codesys platform plugins version 2.6.1.2320, but since I upgraded to versions 2.7 and even 2.8, some files are no longer imported correctly. After some research, I identified that all the files containing variables of the type "POINTER TO" are affected. I have attached a screenshot of the error I am encountering. Do you know about this bug? Do you plan to fix it?
Last updated: 2025-03-26

Post by hemuv on Dialog Open ^{CODESYS Forge talk (Post)}
I'm programming an HMI for a machine. I want to log all the parameter's changes (used text field for displaying and changing) for particular User levels. Created a Numpad and want to log oldvalue and Newvalue on 'ok' Button press. To retrieve the oldvalue, i check if the dialogue opened is my Numpad, Then I retrieve the dialogue interface via GetDialogInterface(ADR(myNumpad)) --> numpadData.stVariableValue which contain my oldvalue and save it locally. Problem is sometimes i retrieve the data and sometimes not. Also observed when Numpad Dialogue is Opened, VisuDlgUtil_IsDialogOpen returns False in some cycles.Attached you will find my Project. please let me know what went wrong or if there is a better approach to collect old and New Value of a textfield. Thank you.
Last updated: 2025-03-26

Post by anlebr on Alarm group template - Is it not possible with several instances? ^{CODESYS Forge talk (Post)}
Hi In the POU section of my project I have created a Fan function block and defined an alarm group template for this FB with one alarm (Motor fault). In the PLC program I define two instances of the fan function block. When going to the alarm configuration and pressing "Create or update alarm instances", I get two alarms listed. So far so good. However, when I start my program and check the alarm table in the visualization I only see one alarm, even if both are active. Am I doing something wrong, or is it not possible to define alarms on a function block level and get one set of alarms per instance of the function block?
Last updated: 2025-04-01

Post by kut69 on Retain / Persistent Variables in Codesys for Raspberry Pi ^{CODESYS Forge talk (Post)}
Hi, I am interested in details about the .ret file in the filesystem. I have already a project where the file is used (write on demand, read by start) and I want to share it as 'default input' for test devices using the identical application. Opening the .ret file content in a hex editor (I only use a single string retain var) I asked myself what the meaning of the first 24 bytes is. It neither contains a handle to the application nor a reference to the variable. Is this maybe a timestamp? Or a CRC/checksum? Regards, Thomas
Last updated: 2025-05-19

Post by qkkk on Device Scan ^{CODESYS Forge talk (Post)}
Hello all, I have developed a custom I/O driver in CODESYS that communicates via a Unix Domain Socket. In my DeviceDescription.xml, I have set up the following: <scan supported="true"> <scanfbinstance fbname="IOScanDevice"> The goal is to allow the user to scan for connected I/O modules from the CODESYS GUI ("Scan for Devices") and automatically populate the device tree with detected submodules.</scanfbinstance></scan> The function block IOScanDevice is implemented in the driver library and added to the main device's FB instances. However, when I initiate the scan from the GUI, nothing appears to happen the function is not executed. Is there an example project or driver (open source or from CODESYS Forge) that demonstrates a working custom scan implementation?
Last updated: 2025-05-26

Post by hclai on Maximum Array Index Issue ^{CODESYS Forge talk (Post)}
I was trying to use a table object in visualization. I want to dynamically show the valid rows in the table. However, it does not work when there is 1 row. i put the maximum array index to 1. it does not show the 1st row. when i change to 2, it show the second row only. my project with older visualization profile version is working perfectly fine. I did some test and realized that i must use a Row Selection variable to change from 0 to 1. With this change of Row selection, then the row 1 will show up.
Last updated: 2025-06-19

Post by alsiddhartha on TextList name error (fake) ^{CODESYS Forge talk (Post)}
Hello, I’m developing a program and for some reason I got this error: C0193: Name '2,Recipe #2GVL' is no valid identifier I was creating a combo box and creating a TextList for my recipe. I couldn't find where the error was, until in the combo box properties in the 'Text List' property in the options it gives me to select, I found '2,Recipe #2' to be able to select (I never created a list with this name) and I can't find a way to delete that option or I can't find where that list is. I tried to delete the TextLists, delete the combo box, to clean the project, but the error still there. How can I delete this option (2,Recipe #2)? Or how can I fix this error?** Thank you.
Last updated: 2025-06-19

Post by scoob on ModbusFB - Slow Response Time ^{CODESYS Forge talk (Post)}
Hello, I have been trying to use the ModbusFB functions so I can put some code into libraries, but it seems to be very slow for me. I have a Modbus device with 100ms registers. I previously setup 10 channels in the 'traditional' Modbus Slave with channels and mappings - and set a cyclic trigger at 100ms - this worked fine. I then tried the ModbusFB example, and setup reading the same 10 blocks of modbus addresses, copying the example and putting all of the requests into an array and triggering the requests sequentially. I timed how long the requests are taking to get round to each one, and it is around 1s 450ms. How do I speed this up to match the cyclic time? IF NOT(init) THEN init := TRUE; // Set the required IP address: ipAddress[0] := 192; ipAddress[1] := 168; ipAddress[2] := 1; ipAddress[3] := 10; // Pass the required IP address to the clinet FB: client_NetworkSwitch.aIPaddr := ipAddress; client_NetworkSwitch.udiLogOptions := (ModbusFB.LoggingOptions.ClientConnectDisconnect OR ModbusFB.LoggingOptions.ClientReceivedValidReplies); // Try to connect the client client_NetworkSwitch(xConnect:=TRUE); // Configure all the channels to read connecting them to the client: portStatus_Request(rClient := client_NetworkSwitch, uiStartItem := 4096, uiQuantity := 32, pData := ADR(portStatus), udiReplyTimeout := udiReplyTimeout); portSpeed_Request(rClient := client_NetworkSwitch, uiStartItem := 4352, uiQuantity := 32, pData := ADR(portSpeed)); flowControl_Request(rClient := client_NetworkSwitch, uiStartItem := 4608, uiQuantity := 32, pData := ADR(flowControl)); linkUpCounter_Request(rClient := client_NetworkSwitch, uiStartItem := 5888, uiQuantity := 32, pData := ADR(linkUpCounter)); txPacketCounter1_Request(rClient := client_NetworkSwitch, uiStartItem := 8192, uiQuantity := 100, pData := ADR(txPacketCounter1)); txPacketCounter2_Request(rClient := client_NetworkSwitch, uiStartItem := 8292, uiQuantity := 28, pData := ADR(txPacketCounter2)); rxPacketCounter1_Request(rClient := client_NetworkSwitch, uiStartItem := 8448, uiQuantity := 100, pData := ADR(rxPacketCounter1)); rxPacketCounter2_Request(rClient := client_NetworkSwitch, uiStartItem := 8548, uiQuantity := 28, pData := ADR(rxPacketCounter2)); txErrors_Request(rClient := client_NetworkSwitch, uiStartItem := 8704, uiQuantity := 64, pData := ADR(txErrors)); rxErrors_Request(rClient := client_NetworkSwitch, uiStartItem := 8960, uiQuantity := 64, pData := ADR(rxErrors)); // Trigger all client requests initially FOR clientRequestsCnt := 0 TO (SIZEOF(clientRequests)/SIZEOF(clientRequests[0]))-1 DO pClientRequest := clientRequests[clientRequestsCnt]; pClientRequest^.xExecute := TRUE; END_FOR // Prepare sequential trigger / control of client requests. clientRequestsCnt := 0; pClientRequest := clientRequests[clientRequestsCnt]; END_IF // Call the client to do request processing: client_NetworkSwitch(); // Now we trigger client request sequentially ... IF NOT pClientRequest^.xExecute AND NOT pClientRequest^.xDone AND run AND client_NetworkSwitch.xConnected THEN pClientRequest^.xExecute := TRUE; END_IF // .. and check result/error IF pClientRequest^.xExecute AND run AND client_NetworkSwitch.xConnected THEN IF pClientRequest^.xDone THEN // Prepare next trigger of client request (a rising edge of xExecute) pClientRequest^.xExecute := FALSE; IF clientRequestsCnt < SIZEOF(clientRequests)/SIZEOF(clientRequests[0])-1 THEN // next client request clientRequestsCnt := clientRequestsCnt + 1; ELSE clientRequestsIterationCounter := clientRequestsIterationCounter + 1; clientRequestsCnt := 0; END_IF pClientRequest := clientRequests[clientRequestsCnt]; END_IF END_IF I did try a semi-coded way using the IoDrvModbusTCP library, and setting the slave com settings, then 10 commands and 10 requests, then using a TP on xDone as a pause, before triggering another request - this is time the delay is around 120ms - so the device is fine with the speed, just something I am doing wrong in the ModbusFB method I am sure.
Last updated: 2024-04-26

Post by mp9876 on Device logon problem following fresh install ^{CODESYS Forge talk (Post)}
All screenshots are enclosed in MS Word document. NOTE; 4 questions features at the end. Any assistance would be greatly appreciated! Hi everyone, I am still having device logon problem following a fresh install Here are the STEPS I went through following a FRESH CODESYS Win 64 3.5.19.60 install on a different computer. ‘Gateway not configured properly’ when attempting to REFRESH from the Users and Groups. Then did Gateway manage and confirmed it was ok: This message popped out as it was a fresh install: YES then: Initially went with Administrator twice (user & password) but it did not like it. No device is responding to …: Continued by setting a new user Pressed OK and obtained the following message: Stopped and Restarted PLC at that point: Obtained the following: Attempted to login a 2nd time without success. Then I scanned the network to see if matching device can be detected: Only way to get it detected was to remove the tick in the ‘Hide non-matching devices…’ Attempted a WINK but got a return like this one: REFRESH either @ Users and Groups or @ Access Rights returns: Then created user ‘mp’ at Project level ang logged in: Understandably device user mp9876 was not valid for the Project. Device information A few questions comes to my mind following these connection attempts: 1- Gateway not configured properly message pops out because of a non-compatible device ? 2- Why would the device not be compatible ? 3- Any way to make the device compatible ? 4- Any ideas on how to get this connectivity problem to the device solved ?
Last updated: 2024-03-17

Post by mubeta on Some 'pathetic' errors in SoftMotion program ^{CODESYS Forge talk (Post)}
Thank you for your interest. Your answers are in line with what I knew, so at least it comforts me that I did not misinterpret the situation. However, I don't have an exact match as, for this project over the past few days I have: 1) I have gone back to leaving the various FBs of the motion always called, all of them, and in the state machine I use a boolean to activate the various useful Execute. (But in the future I want to go back and try the programming technique with which I wanted to develop this project); 2) For the occasional error: SMC_FB_WASNT_CALLED_DURING_MOTION perhaps it was due to the fact that I had set the Ethercat bus synchronism only at the CAN master level, but not at the level of individual drives. I have now also activated it for the individual drives and it does indeed seem to have been resolved, but having also adopted the programming technique mentioned in point 1), I cannot say whether this was the solution to the problem, or instead the previous point. Is there an error ‘regulator or start not set’ in the device log before the error ‘motion generating FB wasn't called for at least one cycle’? I can't answer that right now. By now the machine is running and I am no longer there, at this one. Also, I seem to remember that the 'fbeFBerror' drive structure (5-element array), does not cycle, BUT ONCE THE 5 EVENTS AFTER SWITCHING ON, IT DOES NOT UPDATE ANYMORE (but that's another issue), so diagnostics were not easy.
Last updated: 2024-07-24

Post by edson-bueno on SysProcess Execute Command unable to run commands with special characters ^{CODESYS Forge talk (Post)}
Hi, I found the same issue, and I fixed with this steps: 1st go to codesys .cfg file. sudo nano CODESYSControl.cfg Then insert this: [SysProcess] BasePriority=Realtime Command=AllowAll Now we need to grant codesys root rights on Linux. Step 1: Create or edit the systemd override configuration: sudo systemctl edit codesyscontrol In the editor that opens, insert: [Service] User=root Save and exit: Press Ctrl+O to save Press Ctrl+X to exit Step 2: Reload systemd and reboot To apply the override: sudo systemctl daemon-reexec sudo systemctl daemon-reload sudo reboot Step 3: Confirm CODESYS is running as root After reboot, open the terminal and run: ps aux | grep codesyscontrol You should see something like: root 1234 ... /opt/codesys/bin/codesyscontrol.bin ... If instead it shows admin or another user, the override was not applied correctly. Step 4: (Optional) Confirm from within CODESYS In your CODESYS project, insert this test code to run the Linux command whoami: Make sure the lib SysProcessImplementation, SysTypes, and CmpErrors is on the project. VAR sCommand : STRING := '/usr/bin/whoami'; sOutput : STRING(255); refCommand : REFERENCE TO STRING; refOutput : REFERENCE TO STRING; resultCmd : UDINT; END_VAR refCommand REF= sCommand; refOutput REF= sOutput; SysProcessExecuteCommand2( pszCommand := refCommand, pszStdOut := refOutput, udiStdOutLen := SIZEOF(sOutput), pResult := ADR(resultCmd) ); Notes & Warnings This method gives full system access to the CODESYS runtime — do not expose this system to the public network without protection. Do not use sudo in commands inside CODESYS when the runtime is already running as root. @tomas111, in case you want to read the temperatur, use this command: sCommand:STRING:='/usr/bin/vcgencmd measure_temp';
Last updated: 2025-05-20

Sort by relevance or date